The pll6 has a /4 output that is used as an input to the ahb mux clock.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current sunxi clock driver has the base factor clock of divs clocks
as the last clock output of the clock node. This makes it rather difficult
to add new outputs, such as fixed dividers, which were previously unknown.
This patch makes the divs clocks data structure specify which output is
the factor clock, and updates all current divs clocks accordingly.
We can then add new outputs after the factor clocks, at least not breaking
backward compatibility with regards to the devicetree bindings.
Also replace kzalloc with kcalloc in sunxi_divs_clk_setup().
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We want to reparent AHB clock to PLL6 on sun5i/sun7i using the assigned
clocks properties. AHB is a factor clock, while PLL6 is a divs clock.
Register divs clocks before factor clocks so reparenting works. This
is only needed because we do the reparenting on the clock provider.
The proper way to fix this is to split out all the old sunxi clocks
into separate CLK_OF_DECLARE statements, like we are doing for sun9i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the ahb clock on sun5i/sun7i is muxable, ahb is no longer
guaranteed to be a child of the cpu clock. Add the cpu clock to
the list of protected clocks so it doesn't get disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AHB clock on sun5i and sun7i are muxable divider clocks.
Use a factors clock to support them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB controller/phy clocks and reset controls are in a separate
address block, unlike previous SoCs where they were in the clock
controller. Also, access to the address block is controlled by a
clock gate to AHB.
Add support for resets requiring a clock to be enabled when
asserting/deasserting the reset controls, and add the sun9i USB
clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB clocks originally shared code with the gates clocks, but had
additional reset controllers. Move these to a separate file. This will
allow us to add new support for slightly different USB clocks, such as
on the A80, without affecting gates clocks, and also facilitate the
migration of gates clocks to a generic solution.
This also cleans up the USB clocks code slightly, such as adding
newlines, getting rid of the unused clkdev call, using a simple
u32 instead of BITMAP for the clock masks, using BIT() macro to
declare the clock bitmasks, and using of_io_request_and_map() to
get the I/O address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The old implementation of sun9i_a80_get_pll4_factors() has several issues,
it checks against 256 / 512 in various places where it should use 255 / 511,
it does the wrong thing for low frequencies which are an even multiple of
6 MHz, e.g. if you ask it for 72 MHz it will result in 144 Mhz, and it does
not take into account that n must be at least 12. Moreover it is quite hard
to read / follow it.
This commit rewrites it to be correct in all cases, and makes it much easier
to follow the code / to read.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A80 SoC, the 4 mmc controllers each have a separate register
controlling their register access clocks and reset controls. These
registers in turn share a ahb clock gate and reset control.
This patch adds a platform device driver for these controls. It
requires both clocks and reset controls to be available, so using
CLK_OF_DECLARE might not be the best way.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The module 0 style clocks, or storage module clocks as named in the
official SDK, are almost the same as the module 0 clocks on earlier
Allwinner SoCs. The only difference is wider mux register bits.
As with earlier Allwinner SoCs, mmc module clocks are a special case
of mod0 clocks, with phase controls for 2 child clocks, output and
sample.
This patch adds support for both.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The only difference between module clocks on different platforms is the
width of the mux register bits and the valid values, which are passed in
through struct factors_data. The phase clocks parts are identical.
This patch generalizes the setup function, so most of the code can be
reused when adding sun9i support, which has a wider mux register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we don't have any user left for our custom phase function, we can
safely remove this hack from the code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Instead of having three different clocks for the main MMC clock and the two
phase sub-clocks, which involved having three different drivers sharing the
same register, rework it to have the same single driver registering three
different clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
The cpu clock on sunxi machines is just a mux clock, which is normally
fed by the main PLL, but can be muxed to the main or low power oscillator.
Make the mux clock propagate rate changes to its parent, so we can
change the clock rate of the PLL, and thus actually implement rate
changing on the cpu clock.
This patch also removes the no reparenting limit.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With the prcm in sun6i (and some later SoCs) some mod0 clocks are instantiated
through the mfd framework, and as such do not work with of_clk_declare, since
they do not have registers assigned to them yet at of_clk_declare init time.
Silence the error on not finding registers in the of_clk_declare mod0 clk
setup method, and also register mod0-clk support as a platform driver to work
properly with mfd instantiated mod0 clocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
So far the A31s is 100% compatible with the A31, still lets do the same
as what we've done for the A13 / A10s and give it its own compatible string,
in case we need to differentiate later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Removed unusude CPU_OF_DECLARE_METHOD]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi factor clocks usage was changed in
clk: sunxi: Give sunxi_factors_register a registers parameter
However the sun9i core clocks were not fixed up in that patch,
resulting in breakage. This patch fixes that.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Before this commit sunxi_factors_register uses of_iomap(node, 0) to get
the clk registers. The sun6i prcm has factor clocks, for which we want to
use sunxi_factors_register, but of_iomap(node, 0) does not work for the prcm
factor clocks, because the prcm uses the mfd framework, so the registers
are not part of the dt-node, instead they are added to the platform_device,
as platform_device resources.
This commit makes getting the registers the callers duty, so that
sunxi_factors_register can be used with mfd instantiated platform device too.
While at it also add error checking to the of_iomap calls.
This commit also drops the __init function from sunxi_factors_register since
platform driver probe functions are not __init.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch unifies the sun6i AHB1 clock, originally supported
with separate mux and divider clks. It also adds support for
the pre-divider on the PLL6 input, thus allowing the clock to
be muxed to PLL6 with proper clock rate calculation.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ahb1_sdram clock gate is only used for accessing the sdram
controller's registers over the bus. It is not used for actually clock
the controller or the dram, hence it does not need to be protected.
This also gets rid of the problem when the protected ahb1_sdram gate
is prepared/enabled while it is still an orphan, and the operation
is not propagated to the correct parent.
This was confirmed on my A23 tablet and my A31 Hummingbird.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is in preparation for clock providers to not have to deal with struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
A CLK_MUX_INDEX_BIT mux has one bit per parent, but the sun7i-a20-gmac-clk
has 2 bits selecting between 3 possible parents using values of 0, 1, 2,
which makes it a regular mux which should not have CLK_MUX_INDEX_BIT set in
its flag.
However we do not support parent 1 (an external clock), so use a table to
select parent 0 or 2, which are the 2 parents we support.
Note this has not been causing any issues sofar, because we start with a
parent setting of parent 0, and only ever re-parent to parent 2 (for which
we use an index of 1 as we skip parent 1) and with CLK_MUX_INDEX_BIT set
we write a value of 2 for index 1.
Tested on both a cubietruck (which uses rgmii mode) as well as a cs908
(an a31s board which uses mii mode).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock modules on the A31 use PLL6x2 as one of their inputs.
This patch changes the PLL6 implementation for A31 to a divs clock,
i.e. clock with multiple outputs that have different dividers.
The first output will be the normal PLL6 output, and the second
will be PLL6x2.
This patch fixes the PLL6 N factor in the clock driver, and removes
any /2 dividers in the PLL6 factors clock part. The N factor counts
from 1 to 32, mapping to values 0 to 31, as shown in the A31 manual.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently sunxi_divs_clk_setup assumes the number of child clocks
to be the same as the number of clock-output-names, and a maximum
of SUNXI_DIVS_MAX_QTY child clocks.
On sun6i, PLL6 only has 1 child clock, but the parent would be used
as well, thereby also having it's own clock-output-names entry. This
results in an extra bogus clock being registered.
This patch adds an entry for the number of child clocks alongside
the data structures for them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This driver does not match the hardware, which is actually compatible
to sun4i-a10-apb1-clk. Since we've switch to the correct one, drop
this driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit unifies the APB1 mux with the APB1 clock, using the new
factors infrastructure.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
[wens@csie.org: Add mux mask bits]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the gate clocks for AHB/APB busses on the A80 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has 12 PLL clocks, 3 AHB clocks, 2 APB clocks, and a
new "GT" bus, which I assume is some kind of data bus connecting
the processor cores, memory and various busses. Also there is a
bus clock for a ARM CCI400 module.
As far as I can tell, the GT bus and CCI400 bus clock must be
protected.
This patch adds driver support for peripheral related PLLs and
bus clocks on the A80. The GT and CCI400 clocks are added as well
as these 2 along with the PLLs they are clocked from must not be
disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some of the factors-style clocks on the A80 have different widths
for the mux values in the registers.
Add a .muxmask field to clk_factors_config to make it configurable.
Passing a bitmask instead of a width parameter will allow reuse
in case we support table-based muxes in the future.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The most important part of this serie is the addition of the phase API to
handle the MMC clocks in the Allwinner SoCs.
Apart from that, the A23 gained a new mbus driver, and there's a fix for a
incorrect divider table on the APB0 clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZkI9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner Clocks Additions for 3.18
The most important part of this serie is the addition of the phase API to
handle the MMC clocks in the Allwinner SoCs.
Apart from that, the A23 gained a new mbus driver, and there's a fix for a
incorrect divider table on the APB0 clock.
The MBUS clock on sun8i is slightly different from the old mod0 clocks.
The divider is 3 bits wider, while also needing a divider table for the
higher 4 values, which all set the same divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MMC clock we thought we had until now are actually not one but three
different clocks.
The main one is unchanged, and will have three outputs:
- The clock fed into the MMC
- a sample and output clocks, to deal with when should we output/sample data
to/from the MMC bus
The phase control we had are actually controlling the two latter clocks, but
the main MMC one is unchanged.
We can adjust the phase with a 3 bits value, from 0 to 7, 0 meaning a 180 phase
shift, and the other values being the number of periods from the MMC parent
clock to outphase the clock of.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Move the MBUS clock to the module clocks file. It's pretty trivial, but still
requires to enable the clocks to make sure it won't get disabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Since we know have the ability to declare factors clock outside of clk-sunxi,
create a new mod0 driver to deal with the mod0 clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Even though the mbus clock is a regular module clock, given its nature, it
needs to be enabled all the time.
Introduce a new compatible, to differentiate it from the other module clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Until now, the factors clock probing was done directly by sunxi_init_clocks,
with the factors registration being called directly with the clocks data passed
as an argument.
This approch has shown its limits when we added more clocks, since we couldn't
really split code with such a logic in smaller files, and led to a huge file
having all the clocks.
Introduce an intermediate probing function, so that factor clocks will be able
to directly be called by CLK_OF_DECLARE, which will in turn ease the split into
several files.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The sun4i-apb0 clock, as found on all platforms using it, is a
power-of-two-based divider clock, with a special divider of 2
for value 0.
This was causing the clock framework to incorrectly calculate
the clock rate for apb1 and related modules on sun6i and sun8i.
On sun[4/5/7]i, u-boot SPL configures the divider with value 1
for /2 divider, so no suprises there.
This patch adds a proper divider table for it, so the correct
clock rate can be calculated.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There are some structs and arrays on the driver that are not used
anywhere else. Let's mark them as static.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This commit adds __iomem thoughout the sunxi clock driver, in places
where it was ommited. This cleans most of the sparse warnings we
are getting here.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This pull request adds support for the clocks found in the newly supported
Allwinner A23 clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=85He
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next-sunxi
Allwinner clocks additions for 3.17
This pull request adds support for the clocks found in the newly supported
Allwinner A23 clocks.
This patch adds "allwinner,sun8i-a23-apb0-gates-clk", a A23 specific
compatible to the sun6i-a31-apb0-gates clock driver, along with the
gate bitmap.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun6i-apb0-gates uses the "clock-indices" DT property to indicate
valid gate bits or holes in between. However, the rest of sunxi
clock drivers use bitmaps for this purpose.
This patch modifies sun6i-apb0-gates to use bitmaps as well, to be
consistent with the sunxi platform. Also add the missing call to
clk_register_clkdev, so system clock lookups will work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun6i-a31-apb0-gates supports using clock-indices for holes between
individual gates. However, the driver passes the number of gates
registered in clk_data->clk_num, which of_clk_src_onecell_get uses
to recognize the range of valid indices a consumer can use.
This patch makes the driver pass the maximum gate index + 1, so
of_clk_src_onecell_get does not complain about indices greater
than gates registered.
This was tested on the A23 SoC, which has a similar APB0 clock,
but has holes for gates to removed IP blocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 has an almost identical PRCM clock tree. The difference in
the APB0 clock is the smallest divisor is 1, instead of 2.
This patch adds a separate sun8i-a23-apb0-clk driver to support it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock control unit on the A23 is similar to the one found on the A31.
The AHB1, APB1, APB2 gates on the A23 are almost identical to the ones
on the A31, but some outputs are missing.
The main CPU PLL (PLL1) however is like that on older Allwinner SoCs,
such as the A10 or A20, but the N factor starts from 1 instead of 0.
This patch adds support for PLL1 and all the basic clock muxes and gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A few of the clock modules have odd dividers, such as
the 2 lowest dividers being the same (2), or have the
same divider when the highest bit is set.
This patch adds support for optional divider tables,
so the clock framework will know about the odd values.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
