A delay is needed each time the chip selected becomes inactive,
even after burst data readings are performed.
Currently, there is no delay added after a burst reading
and in case a new SPI transfer is performed before
the needed delay, the adis device becomes unresponsive until
reset.
This commit is adding the needed delay directly to the spi driver,
using the cs_inactive parameter, in case it is not set and is
removing the additional chip select change delay present in adis
APIs to remove the double delay.
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Link: https://lore.kernel.org/r/20231027140358.328699-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the standard max() helper macros instead of direct variable comparison
using if/else blocks or ternary operator. Change identified using
minmax.cocci Coccinelle semantic patch.
Signed-off-by: Bragatheswaran Manickavel <bragathemanick0908@gmail.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20231027094410.3706-1-bragathemanick0908@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are two spelling mistakes in dev_err messages. Fix them.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20231023081054.617292-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Improve device detection in certain chip families known to have
various chip IDs. When no ID matches, give a warning but follow
along what device said on the firmware side and try to configure
it.
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Link: https://lore.kernel.org/r/eade22d11e9de4405ea19fdaa5a8249143ae94df.1697994521.git.ang.iglesiasg@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The RGB + IR data can be used to calculate the illuminance value (luxes).
Implement the equation obtained from the ROHM HW colleagues and add a
raw light data channel outputting illuminance values in (nano) Luxes.
Both the read_raw and buffering values are supported, with the limitation
that buffering is only allowed when a suitable scan-mask is used. (RGB+IR,
no clear).
The equation has been developed by ROHM HW colleagues for open air sensor.
Adding any lens to the sensor is likely to impact to used c1, c2, c3
coefficients. Also, the output values have only been tested on BU27008.
According to the HW colleagues, the very same equation should work on
BU27010 as well.
Calculate and output illuminance values from BU27008 and BU27010.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ZTJcOxSb/WHzdN8h@dc78bmyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
They are appear to be spelling mistakes,
drivers/iio/pressure/bmp280.h:413 endianess->endianness
drivers/iio/pressure/bmp280-core.c:923 dregrees->degrees
drivers/iio/pressure/bmp280-core.c:1388 reescale->rescale
drivers/iio/pressure/bmp280-core.c:1415 reescale->rescale
Signed-off-by: Li peiyu <579lpy@gmail.com>
Link: https://lore.kernel.org/r/20231021070903.6051-1-579lpy@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for the optional reset gpio to the ad2s1210 resolver
driver. If the gpio is present in the device tree, it is toggled during
driver probe before the reset of the device initialization. As per the
devicetree bindings, it is expected for the gpio to configured as active
low.
Suggested-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20231016154311.38547-1-dlechner@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is possible to use the AD2S1210 with hardwired mode pins (A0 and A1).
According to the devicetree bindings, in this case the adi,fixed-mode
property will specify which of the 3 possible modes the mode pins are
hardwired for and the gpio-modes property is not allowed.
This adds support for the case where the mode pins are hardwired for
config mode. In this configuration, the position and value must be read
from the config register.
The case of hardwired position or velocity mode is not supported as
there would be no way to configure the device.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231016135423.16808-1-dlechner@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Bosch BMI323 is a 6-axis low-power IMU that provide measurements for
acceleration, angular rate, and temperature. This sensor includes
motion-triggered interrupt features, such as a step counter, tap detection,
and activity/inactivity interrupt capabilities.
The driver supports various functionalities, including data ready, FIFO
data handling, and events such as tap detection, step counting, and
activity interrupts.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20231013034808.8948-3-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MAX34408/MAX34409 are two- and four-channel current monitors that are
configured and monitored with a standard I2C/SMBus serial interface. Each
unidirectional current sensor offers precision high-side operation with a
low full-scale sense voltage. The devices automatically sequence through
two or four channels and collect the current-sense samples and average them
to reduce the effect of impulse noise. The raw ADC samples are compared to
user-programmable digital thresholds to indicate overcurrent conditions.
Overcurrent conditions trigger a hardware output to provide an immediate
indication to shut down any necessary external circuitry.
Add as ADC driver which only supports current monitoring for now.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/MAX34408-MAX34409.pdf
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Link: https://lore.kernel.org/r/20231014211254.16719-3-fr0st61te@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTSzg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylH3QCfbZuG8MiglEZUd4slRLUNqcRQ5tQAn1yKpDFo
l3KLkxo1UTLMXbJBWe+b
=gafK
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
-----BEGIN PGP SIGNATURE-----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=wth0
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
As noted by Jonathan Cameron: it is perfectly legal for a channel
to have an offset but no scale in addition to the raw interface.
The conversion will imply that scale is 1:1.
Make rescale_configure_channel() accept just scale, or just offset
to process a channel.
When a user asks for IIO_CHAN_INFO_OFFSET in rescale_read_raw()
we now have to deal with the fact that OFFSET could be present
but SCALE missing. Add code to simply scale 1:1 in this case.
Link: https://lore.kernel.org/linux-iio/CACRpkdZXBjHU4t-GVOCFxRO-AHGxKnxMeHD2s4Y4PuC29gBq6g@mail.gmail.com/
Fixes: 53ebee9499 ("iio: afe: iio-rescale: Support processed channels")
Fixes: 9decacd8b3 ("iio: afe: rescale: Fix boolean logic bug")
Reported-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230902-iio-rescale-only-offset-v2-1-988b807754c8@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Second interrupt is needed only when touchscreen mode is used, so don't
request it unconditionally. This removes the following annoying warning
during boot:
exynos-adc 14d10000.adc: error -ENXIO: IRQ index 1 not found
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20231009101412.916922-1-m.szyprowski@samsung.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006224440.442864-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some devices do not support delta angle and delta velocity
burst readings, which means there should be no buffer support
for these types of channels.
A new list of channels is created which contains the delta
channels structures with the scan index equal to -1 to allow
for raw register readings, without buffer support.
This list of channels is assigned to the devices which
do not support delta angle and delta velocity burst
readings.
Fixes: 8f6bc87d67 ("iio: imu: adis16475.c: Add delta angle and delta velocity channels")
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231012122456.765709-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To be consistent with the rest of iio, remove of_match_ptr(). It does
not do anything useful here.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231012-ad2s1210-mainline-v1-2-b2ee31c0e9dd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DRV_NAME macro is only used in one place in the ad2s1210 driver and
is not really needed so let's remove it.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231012-ad2s1210-mainline-v1-1-b2ee31c0e9dd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver was previously using offset and scale values for the
temperature sensor readings which were only valid for 7-series devices.
Add per-device-type values for offset and scale and set them appropriately
for each device type.
Note that the values used for the UltraScale family are for UltraScale+
(i.e. the SYSMONE4 primitive) using the internal reference, as that seems
to be the most common configuration and the device tree values Xilinx's
device tree generator produces don't seem to give us anything to tell us
which configuration is used. However, the differences within the UltraScale
family seem fairly minor and it's closer than using the 7-series values
instead in any case.
Fixes: c2b7720a79 ("iio: xilinx-xadc: Add basic support for Ultrascale System Monitor")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-3-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the probe function, the driver was reading out the thresholds already
set in the core, which can be configured by the user in the Vivado tools
when the FPGA image is built. However, it later clobbered those values
with zero or maximum values. In particular, the overtemperature shutdown
threshold register was overwritten with the max value, which effectively
prevents the FPGA from shutting down when the desired threshold was
eached, potentially risking hardware damage in that case.
Remove this code to leave the preconfigured default threshold values
intact.
The code was also disabling all alarms regardless of what enable state
they were left in by the FPGA image, including the overtemperature
shutdown feature. Leave these bits in their original state so they are
not unconditionally disabled.
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-2-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a new optional field to struct iio_info to allow drivers to
specify a label for the event. This is useful for cases where there are
many events or the event attribute name is not descriptive enough or
where an event doesn't have any other attributes.
The implementation is based on the existing label support for channels.
So either all events of a device have a label attribute or none do.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-12-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
simplified the driver with devm hooks, but wrongly states that the
platform_set_drvdata(), platform_get_drvdata() are unused after the
simplification: the driver data is infact used in .suspend() and
.resume() PM callbacks, currently producing a kernel panic.
Reintroduce the call to platform_set_drvdata() in the probe function
Fixes: a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231010121940.159696-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add fast settling mode support for AD7193.
Add two new device specific attributes: oversampling_ratio and
oversampling_ratio_available.
For AD7193 the user can set the average factor by writing to
oversampling_ratio. The possible values are exposed when reading
oversampling_ratio_available.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20231010124927.143343-4-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The avdd and the reference voltage are two different sources but the
reference voltage was assigned according to the avdd supply.
Add vref regulator structure and set the reference voltage according to
the vref supply from the devicetree.
In case vref supply is missing, reference voltage is set according to
the avdd supply for compatibility with old devicetrees.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230924152149.41884-1-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After enabling/disabling interrupts on the vcnl4040 chip the als and/or
ps sensor is powered on or off depending on the interrupt enable bits.
This is made as a last step in write_event_config.
But there is no reason to do this as the runtime PM handles the power
state of the sensors. Interfering with this may impact sensor readings.
Consider the following:
1. Userspace makes sensor data reading which triggers RPM resume
(sensor powered on) and a RPM suspend timeout. The timeout is 2000ms
before RPM suspend powers the sensor off if no new reading is made
within the timeout period.
2. Userspace disables interrupts => powers sensor off
3. Userspace reads sensor data = 0 because sensor is off and the
suspend timeout has not passed. For each new reading made within the
timeout period the timeout is renewed with 2000ms and RPM will not
make a new resume (device was not suspended). So the sensor will
not be powered on.
4. No further userspace reading for 2000ms ends RPM suspend timeout and
triggers suspend (powers off already powered off sensor).
Powering sensor off in (2) makes all consecutive readings made within
2000ms to the previous reading (3) return invalid data.
Skip setting power state when writing new event config.
Fixes: 546676121c ("iio: light: vcnl4000: Add interrupt support for vcnl4040")
Fixes: bc292aaf9c ("iio: light: vcnl4000: add illuminance irq vcnl4040/4200")
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230907-vcnl4000-pm-fix-v2-1-298e01f54db4@axis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Building ad74413r without selecting IIO_BUFFER and
IIO_TRIGGERED_BUFFER generates error with respect to the iio trigger
functions that are used within the driver.
Update the Kconfig accordingly.
Fixes: fea251b6a5 ("iio: addac: add AD74413R driver")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230912085421.51102-1-antoniu.miclaus@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abce ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses IIO triggered buffers so it needs to select them in
Kconfig.
on riscv-32bit:
/opt/crosstool/gcc-13.2.0-nolibc/riscv32-linux/bin/riscv32-linux-ld: drivers/iio/imu/bno055/bno055.o: in function `.L367':
bno055.c:(.text+0x2c96): undefined reference to `devm_iio_triggered_buffer_setup_ext'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/40566b4b-3950-81fe-ff14-871d8c447627@infradead.org/
Fixes: 4aefe1c2bd ("iio: imu: add Bosch Sensortec BNO055 core driver")
Cc: Andrea Merello <andrea.merello@iit.it>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230903113052.846298-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC Command Buffer Register high and low are currently pointing to
the wrong address and makes it impossible to perform correct
ADC measurements over all channels.
According to the datasheet of the imx8qxp the ADC_CMDL register starts
at address 0x100 and the ADC_CMDH register starts at address 0x104.
This bug seems to be in the kernel since the introduction of this
driver.
This can be observed by checking all raw voltages of the adc and they
are all nearly identical:
cat /sys/bus/iio/devices/iio\:device0/in_voltage*_raw
3498
3494
3491
3491
3489
3490
3490
3490
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230904220204.23841-1-embed3d@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
cros_ec_sensors_push_data() reads `indio_dev->active_scan_mask` and
calls iio_push_to_buffers_with_timestamp() without making sure the
`indio_dev` stays in buffer mode. There is a race if `indio_dev` exits
buffer mode right before cros_ec_sensors_push_data() accesses them.
An use-after-free on `indio_dev->active_scan_mask` was observed. The
call trace:
[...]
_find_next_bit
cros_ec_sensors_push_data
cros_ec_sensorhub_event
blocking_notifier_call_chain
cros_ec_irq_thread
It was caused by a race condition: one thread just freed
`active_scan_mask` at [1]; while another thread tried to access the
memory at [2].
Fix it by calling iio_device_claim_buffer_mode() to ensure the
`indio_dev` can't exit buffer mode during cros_ec_sensors_push_data().
[1]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/industrialio-buffer.c#L1189
[2]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c#L198
Cc: stable@vger.kernel.org
Fixes: aa984f1ba4 ("iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230829030622.1571852-1-tzungbi@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When compiling with gcc 13 with -Warray-bounds enabled:
In file included from drivers/iio/proximity/irsd200.c:15:
In function ‘iio_push_to_buffers_with_timestamp’,
inlined from ‘irsd200_trigger_handler’ at drivers/iio/proximity/irsd200.c:770:2:
./include/linux/iio/buffer.h:42:46: error: array subscript ‘int64_t {aka long long int}[0]’
is partly outside array bounds of ‘s16[1]’ {aka ‘short int[1]’} [-Werror=array-bounds=]
42 | ((int64_t *)data)[ts_offset] = timestamp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~
drivers/iio/proximity/irsd200.c: In function ‘irsd200_trigger_handler’:
drivers/iio/proximity/irsd200.c:763:13: note: object ‘buf’ of size 2
763 | s16 buf = 0;
| ^~~
The problem seems to be that irsd200_trigger_handler() is taking a s16
variable as an int64_t buffer. As Jonathan suggested [1], fix it by
extending the buffer to a two-element array of s64.
Link: https://github.com/KSPP/linux/issues/331
Link: https://lore.kernel.org/lkml/20230809181329.46c00a5d@jic23-huawei/ [1]
Fixes: 3db3562bc6 ("iio: Add driver for Murata IRS-D200")
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Tested-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230810035910.1334706-1-gongruiqi@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Explicity specify array indices to fix mapping between
asahi_compass_chipset and ak_def_array.
While at it, remove unneeded AKXXXX.
Fixes: 4f9ea93afd ("iio: magnetometer: ak8975: Convert enum->pointer for data in the match tables")
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231001-ak_magnetometer-v1-1-09bf3b8798a3@apitzsch.eu
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
strncpy() is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect adc->chan_name[val] to be NUL-terminated based on ch_name's
use within functions that expect NUL-terminated strings like strncmp and
printf-likes:
| if (!strncmp(stm32_adc_ic[i].name, ch_name, STM32_ADC_CH_SZ)) {
| /* Check internal channel availability */
| switch (i) {
| case STM32_ADC_INT_CH_VDDCORE:
| if (!adc->cfg->regs->or_vddcore.reg)
| dev_warn(&indio_dev->dev,
| "%s channel not available\n", ch_name);
...
There is no evidence that NUL-padding is needed either.
Considering the above, a suitable replacement is strscpy() [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding. If, for any reason, NUL-padding _is_
required we should go for `strscpy_pad`.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230921-strncpy-drivers-iio-adc-stm32-adc-c-v1-1-c50eca098597@google.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dt-bindings: iio: Add KX132ACR-LBZ accelerometer
ROHM KX132ACR-LBZ is an accelerometer for industrial applications. It
has a subset of KX022A functionalities, dropping support for tap, free
fall and tilt detection engines. Also, the register interface is an exact
subset of what is found on KX022A (except the WHO_AM_I register value).
Add support for KX132ACR-LBZ.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/272065b9f35b817aff86b7760ff1aaaaaaa969f5.1695879676.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of using the f_order member of ad7192_state, a function that
computes the f_order coefficient makes more sense. This coefficient is a
function of the sinc filter and chop filter states.
Remove f_order member of ad7192_state structure. Instead use
ad7192_compute_f_order function to compute the f_order coefficient
according to the sinc filter and chop filter states passed as
parameters.
Add ad7192_get_f_order function that returns the current f_order
coefficient of the device.
Add ad7192_compute_f_adc function that computes the f_adc value
according to the sinc filter and chop filter states passed as
parameters.
Add ad7192_get_f_adc function that returns the current f_adc value of
the device.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20230924215148.102491-3-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Include bitfield.h and update driver to use bitfield access macros GENMASK,
FIELD_PREP and FIELD_GET.
Remove old macros in favor of using FIELD_PREP and masks.
Change %d to %ld to match the type of FIELD_GET().
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20230924215148.102491-2-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z can measure
pressures ranging from 300 hPa to 1300 hPa with configurable measurement
averaging and internal FIFO. The sensor does also provide temperature
measurements.
Sensor does also contain IIR filter implemented in HW. The data-sheet
says the IIR filter can be configured to be "weak", "middle" or
"strong". Some RMS noise figures are provided in data sheet but no
accurate maths for the filter configurations is provided. Hence, the IIR
filter configuration is not supported by this driver and the filter is
configured to the "middle" setting (at least not for now).
The FIFO measurement mode is only measuring the pressure and not the
temperature. The driver measures temperature when FIFO is flushed and
simply uses the same measured temperature value to all reported
temperatures. This should not be a problem when temperature is not
changing very rapidly (several degrees C / second) but allows users to
get the temperature measurements from sensor without any additional logic.
This driver allows the sensor to be used in two muitually exclusive ways,
1. With trigger (data-ready IRQ).
In this case the FIFO is not used as we get data ready for each collected
sample. Instead, for each data-ready IRQ we read the sample from sensor
and push it to the IIO buffer.
2. With hardware FIFO and watermark IRQ.
In this case the data-ready is not used but we enable watermark IRQ. At
each watermark IRQ we go and read all samples in FIFO and push them to the
IIO buffer.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/4f23211e3cf248f9f48ddb2a752387bb00e9c2c4.1695727471.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some boards fail in magnetometer probe if level shifter flag is not set,
definition was found in the vendor Linux kernel v3.0.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230927173245.2151083-3-andreas@kemnade.info
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The temperature channel has 16-bit storage size. We need to perform
the padding to have the buffer elements naturally aligned in case
the temperature channel is enabled and there are any 32-bit storage
size channels enabled which have a scan index higher than the
temperature channel scan index.
Fixes: 8f6bc87d67 ("iio: imu: adis16475.c: Add delta angle and delta velocity channels")
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230926085721.645687-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The deta angle and deta velocity channels were added in parallel with
color temperature and chromacity so this merge had to assign a
consistent order. I put the color related ones second.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-8-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add channel type for chromaticity.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-7-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-4-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color
temperature, which is measured in kelvin. Thus, add channel type light
color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-3-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor hub attributes can be extended to support more channels. Repeat
the reading for the two existing channels and store them separately. It
still operates in the same manner as before where there was just one
entry. So in order to support more sensor hub attributes for ALS use
channel index to get specific sensor hub attributes.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-2-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-50-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-49-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-47-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20230919174931.1417681-46-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-45-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-44-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-43-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-40-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-36-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-35-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230919174931.1417681-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230919174931.1417681-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230919174931.1417681-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230919174931.1417681-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since Kionix accelerometers use various numbers of bits to report data, a
device-specific function is required.
Implement the function as a callback in the device-specific chip_info structure
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Link: https://lore.kernel.org/r/9c550fb28e34915d473e379f812c7753f7643bae.1694867379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the chip_info structure to the driver's private data to hold all
the device specific infos.
Refactor the kx022a driver implementation to make it more generic and
extensible.
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Link: https://lore.kernel.org/r/7a31d0cdefba15d7c791252ec8bc5db553b3996b.1694867379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Avoid error returns on a failure to match and instead just warn with
assumption that we have a correct dt-binding telling us that
some new device with a different ID is backwards compatible.
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Mehdi Djait <mehdi.djait.k@gmail.com>
Link: https://lore.kernel.org/r/b587cfec2f3350623277005f62121864bee857c7.1694867379.git.mehdi.djait.k@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The STX104 features an 8254 Counter/Timer chip providing three
counter/timers which can be used for frequency measurement, frequency
output, pulse width modulation, pulse width measurement, event count,
etc. The STX104 provides a register bank selection to bank select
between the 8254 Bank and the Indexed Register Array Bank; the Indexed
Register Array is not utilized by this driver, so the 8254 Bank is
selected unconditionally.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230916112031.3634-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_register() is deprecated and devm_clk_hw_register() should be
used as a replacement.
Switching to the clk_hw interface also allows to use the built-in device
managed version of registering the clock provider. The non-clk_hw interface
does not have a device managed version.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230910140903.551081-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet switching to a new channel function implies
multiple steps.
All functions must be selected for a minimum of 130 μs before changing
to another function.
The DAC_CODEx registers are not reset by changing channel functions.
Prior to changing channel functions, it is recommended to set the DAC
code to 0x0000 via the DAC_CODEx registers. Set the channel function
to high impedance via the CH_FUNC_SETUPx registers before transitioning
to the new channel function. After the new channel function is configured,
it is recommended to wait 150 μs before updating the DAC code.
Even though the channel switch is done at only at probe, where a device
reset is performed, that does not guarantee that the steps prior
changing to new channel function should be neglected.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230911142950.216687-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify probe() by replacing id lookup for retrieving match data and
device_get_match_data() by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230903145926.66855-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MCP4725 has a register offset '3' for reading DAC value compared to
'4' for MCP4726. Add dac_reg_offset variable to struct mcp4725_chip_info
to handle this difference.
Drop chip_id from struct mcp4725_chip_info as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-5-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MCP4725 has external voltage reference compared MCP4725 which
has reference embeedded in eeprom. Add use_ext_ref_voltage variable
to struct mcp4725_chip_info to handle this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-4-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add struct mcp4725_chip_info with chan_spec and chip_id variable.
After this simplify probe() by replacing device_get_match_data() and id
lookup for retrieving match data by i2c_get_match_data() by converting
enum->pointer for data in the match table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace the variable 'id' from struct mcp4725_data with local variable
chip_id in probe() as the id variable is not used elsewhere in the
driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903115548.59306-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify adxl345_read_raw() by adding uscale variable to
struct adxl345_chip_info. Also convert variables adxl3{4,7}5_uscale to
macros and use it in OF/ACPI/ID match table.
Drop enum adxl345_device_type as there is no user.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903090051.39274-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in match data table, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Add struct adxl345_chip_info and replace enum->adxl345_chip_info in the
match table and simplify adxl345_probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230903090051.39274-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simpilfy probe() by replacing device_get_match_data() and id lookup for
retrieving match data by using i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230902170529.62297-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simpilfy probe() by replacing device_get_match_data() and id lookup for
retrieving match data by using i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230902163233.56449-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simpilfy probe() by replacing of_device_get_match_data() and id lookup for
retrieving match data by using i2c_get_match_data() by making similar
OF/I2C/ACPI match tables.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230902162633.50546-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The comparator generates an edge on the IRQ like and stays in the
configured state until cleared. Support edge triggered IRQs as well
as not all controllers do support level triggered IRQ.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230831182502.154899-1-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is the iio driver for Microchip family of 153.6 ksps,
Low-Noise 16/24-Bit Delta-Sigma ADCs with an SPI interface
(Microchip's MCP3461, MCP3462, MCP3464, MCP3461R, MCP3462R,
MCP3464R, MCP3561, MCP3562, MCP3564, MCP3561R,
MCP3562R and MCP3564R analog to digital converters).
Signed-off-by: Marius Cristea <marius.cristea@microchip.com>
Link: https://lore.kernel.org/r/20230829154133.40716-3-marius.cristea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2309 is an 8-Channel, 12-Bit SAR ADC with an I2C Interface.
This implements support for all single-ended and differential channels,
in unipolar mode only.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Link: https://lore.kernel.org/r/20230828-ltc2309-v3-2-338b3a8fab8b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use complete device name prefix in the input current offset getter
function.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230830094314.26353-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
of_match_device() may fail and returns a NULL pointer.
In practice there is no known reasonable way to trigger this, but
in case one is added in future, harden the code by adding the check
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_994DA85912C937E3B5405BA960B31ED90A08@qq.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for delta angle and delta velocity raw and buffer
readings to adis16475 driver.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230808075059.645525-4-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The delta velocity is defined as a piece-wise integration of
acceleration data. The delta velocity represents the linear velocity
change between two consecutive measurements and it
is measured in m / s (meters per second).
In order to track the total linear velocity change during a desired
period of time, simply sum-up the delta velocity samples acquired
during that time.
IIO currently does not offer a suitable channel type for this
type of measurements hence this patch adds it.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230808075059.645525-3-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The delta angle is defined as a piece-wise integration of angular
velocity data. The delta angle represents the amount of
angular displacement between two consecutive measurements and it
is measured in radians.
In order to track the total angular displacement during a desired
period of time, simply sum-up the delta angle samples acquired
during that time.
IIO currently does not offer a suitable channel type for this
type of measurements hence this patch adds it.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230808075059.645525-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is nothing from string_helpers.h used in the driver, correct
the header inclusion block accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20230808164152.66748-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is nothing from string_helpers.h used in the driver, correct
the header inclusion block accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/20230808164204.66818-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 0f3a8c3f34 ("iio: Add support for creating IIO devices via configfs")
declared but never implemented iio_sw_device_type_configfs_{un}register().
Commit b662f809d4 ("iio: core: Introduce IIO software triggers") declared but
never implemented iio_sw_trigger_type_configfs_{un}register().
Commit a3e0b51884 ("iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers")
declared but never implemented fxls8962af_core_remove().
Commit 8dedcc3eee ("iio: core: centralize ioctl() calls to the main chardev")
declared but never implemented iio_device_ioctl().
Commit d430f3c36c ("iio: imu: inv_mpu6050: Use regmap instead of i2c specific functions")
removed inv_mpu6050_write_reg() but not its declaration.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230811095701.35372-1-yuehaibing@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Add struct tmp11x_info and replace enum->struct *tmp11x_info for data in
the match table. Drop tmp117_identify() and simplify tmp117_probe() by
replacing device_get_match_data() and id lookup for retrieving data by
i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230812161154.196555-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data()->i2c_get_match_data() to extend matching
support for ID table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Tested-by: Stefan Windfeldt-Prytz <stefan.windfeldt-prytz@axis.com>
Link: https://lore.kernel.org/r/20230812151908.188696-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data()->i2c_get_match_data by making similar I2C
and DT-based matching table to extend matching support for ID table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230812150838.185055-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the ID table, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *ds1803_cfg for data in the ID table and simplify
ds1803_probe() by replacing device_get_match_data() with
i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230812144106.163355-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Add product_id variable to struct sgp_device and remove the local variable
product_id in probe() and replace enum->struct *sgp_device for data in the
match table. Simplify theprobe() by replacing device_get_match_data() and
ID lookup for retrieving data by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230812165730.216180-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds support for the Analog Devices HMC540s 1 dB LSB
Silicon MMIC 4-Bit Digital Positive Control Attenuator, 0.1 - 8 GHz
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Ana-Maria Cusco <ana-maria.cusco@analog.com>
Link: https://lore.kernel.org/r/20230816110906.144540-1-ana-maria.cusco@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Include the corner cases in the computation of the MIXER_VGATE register
value.
According to the datasheet: The MIXER_VGATE values follows the VCM such
as, that for a 0V to 1.8V VCM, MIXER_VGATE = 23.89 VCM + 81, and for a >
1.8V to 2.6V VCM, MIXER_VGATE = 23.75 VCM + 1.25.
Fixes: da35a7b526 ("iio: frequency: admv1013: add support for ADMV1013")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230807143806.6954-1-antoniu.miclaus@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bmp085 EOC IRQ support is optional, but the driver's common probe
function queries the IRQ properties whether or not it exists, which
can trigger a NULL pointer exception. Avoid any exception by making
the query conditional on the possession of a valid IRQ.
Fixes: aae9539496 ("iio: pressure: bmp280: add support for BMP085 EOC interrupt")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230811155829.51208-1-phil@raspberrypi.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Device IDs for AD3542R and AD3552R were swapped leading to unintended
collection of DAC output ranges being used for each design.
Change device ID values so they are correct for each DAC chip.
Fixes: 8f2b54824b ("drivers:iio:dac: Add AD3552R driver support")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reported-by: Chandrakant Minajigi <Chandrakant.Minajigi@analog.com>
Link: https://lore.kernel.org/r/011f480220799fbfabdd53896f8a2f251ad995ad.1691091324.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort ID table alphabetically by name and ACPI table by HID.
While at it, drop blank line before ID table.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818075600.24277-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables to simplify the probe()
by replacing device_get_match_data() and i2c_client_get_device_id by
i2c_get_match_data() as we have similar I2C, ACPI and DT matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818075600.24277-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data()->i2c_get_match_data() to extend matching
support for ID table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: "Crt Mori <cmo@melexis.com>"
Link: https://lore.kernel.org/r/20230812162222.200004-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match table, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *bma180_part_info for data in the match table and
simplify bma180_probe().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230812141044.151520-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data() and i2c_match_id() by
i2c_get_match_data() by making similar I2C and DT-based matching
table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230812072419.42645-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the probe() by replacing device_get_match_data() with
i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230812065741.20990-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort ID table alphabetically by name and OF table by compatible
for single_*bit enums.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20230818173907.323640-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data() and id lookup for retrieving match data
by i2c_get_match_data() by converting enum->pointer for data in the
match table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230818173907.323640-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in match data table, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Add struct sx931x_info and replace enum->sx931x_info in the match table
and simplify sx9310_check_whoami().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230818175819.325663-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the probe() by replacing device_get_match_data() and ID lookup
match by i2c_get_match_data() as we have similar I2C and DT-based matching
table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818183128.334233-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *atlas_device for data in the match table. Simplify
the probe() by replacing device_get_match_data() and ID lookup for
retrieving data by i2c_get_match_data().
While at it, add const qualifier to struct atlas_device and drop inner
trailing commas from OF table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818185531.336672-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *vz89x_chip_data for data in the match table. Simplify
the probe() by replacing device_get_match_data() and ID lookup for
retrieving data by i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818190429.338065-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sort ID table alphabetically by name and OF table by compatible.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230818184033.335502-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the ID table, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Replace enum->struct *mma_chip_info for data in the ID table and simplify
mma8452_probe() by replacing device_get_match_data() with
i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230818184033.335502-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error
is printed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230828064546.2383857-4-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230828064546.2383857-3-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_request_irq() to request the interrupt, so we can avoid
having to manually clean this up.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230828064546.2383857-2-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
Also replace devm_regulator_get() and regulator_enable() with
devm_regulator_get_enable() helper and remove regulator_disable().
Replace iio_device_register() with devm_iio_device_register() and remove
iio_device_unregister().
And st->reg is not used anymore, so remove it.
As Jonathan pointed out, couple of things that are wrong:
1) The device is powered down 'before' we unregister it with the
subsystem and as such userspace interfaces are still exposed which
probably won't do the right thing if the chip is powered down.
2) This isn't done in the error paths in probe.
To solve this problem, register a new callback adf4350_power_down()
with devm_add_action_or_reset(), to enable software power down in both
error and device detach path. So the remove function can be removed.
Remove spi_set_drvdata() from the probe function, since spi_get_drvdata()
is not used anymore.
Fixes: e31166f0fd ("iio: frequency: New driver for Analog Devices ADF4350/ADF4351 Wideband Synthesizers")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230828062717.2310219-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Microchip does have many similar chips, add support for those.
The new supported chips are:
- microchip,mcp3910
- microchip,mcp3912
- microchip,mcp3913
- microchip,mcp3914
- microchip,mcp3918
- microchip,mcp3919
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230822192259.1125792-7-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Name macro parameters after what they represent instead of 'x'
and make sure the evaluation of that will have no side effects.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20230822192259.1125792-6-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The whole file does not make use of indentation properly.
Do something about it.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20230822192259.1125792-5-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace the usage of `adc->spi->dev` with `dev` to make the code prettier.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20230822192259.1125792-4-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify code by switch to dev_err_probe().
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://lore.kernel.org/r/20230822192259.1125792-3-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a device managed hook, via devm_add_action_or_reset() and
mt6577_power_off(), to power off on device detach.
Replace iio_device_register() by devm_iio_device_register() and remove
the mt6577_auxadc_remove() function used to unregister the device and
power off the device.
Remove platform_set_drvdata() from the probe function, since
platform_get_drvdata() is not used anymore.
Remove mt6577_auxadc_mod_reg() call from the probe function error path.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230826035402.3512033-3-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error
is printed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Link: https://lore.kernel.org/r/20230826035402.3512033-2-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error
is printed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230826062733.3714169-3-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
Switch to devm_iio_device_register() and drop the remove function.
This simplifies the code.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230826062733.3714169-2-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230825105746.2999548-3-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH64g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynr2QCfd3RKeR+WnGzyEOFhksl30UJJhiIAoNZtYT5+
t9KG0iMDXRuTsOqeEQbd
=tVnk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.6-rc1.
Stuff all over the place here, lots of driver updates and changes and
new additions. Short summary is:
- new IIO drivers and updates
- Interconnect driver updates
- fpga driver updates and additions
- fsi driver updates
- mei driver updates
- coresight driver updates
- nvmem driver updates
- counter driver updates
- lots of smaller misc and char driver updates and additions
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (267 commits)
nvmem: core: Notify when a new layout is registered
nvmem: core: Do not open-code existing functions
nvmem: core: Return NULL when no nvmem layout is found
nvmem: core: Create all cells before adding the nvmem device
nvmem: u-boot-env:: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
nvmem: sec-qfprom: Add Qualcomm secure QFPROM support
dt-bindings: nvmem: sec-qfprom: Add bindings for secure qfprom
dt-bindings: nvmem: Add compatible for QCM2290
nvmem: Kconfig: Fix typo "drive" -> "driver"
nvmem: Explicitly include correct DT includes
nvmem: add new NXP QorIQ eFuse driver
dt-bindings: nvmem: Add t1023-sfp efuse support
dt-bindings: nvmem: qfprom: Add compatible for MSM8226
nvmem: uniphier: Use devm_platform_get_and_ioremap_resource()
nvmem: qfprom: do some cleanup
nvmem: stm32-romem: Use devm_platform_get_and_ioremap_resource()
nvmem: rockchip-efuse: Use devm_platform_get_and_ioremap_resource()
nvmem: meson-mx-efuse: Convert to devm_platform_ioremap_resource()
nvmem: lpc18xx_otp: Convert to devm_platform_ioremap_resource()
nvmem: brcm_nvram: Use devm_platform_get_and_ioremap_resource()
...
Add filter bypass mode, which bypasses the low pass filter, high pass
filter and disables/unregister the clock rate notifier.
Currently a feature like bypassing the filter is not achievable
straightforward and not very deductive. The user has to look through the
code and call the set_lpf_3db_frequency and set_hpf_3db_frequency iio
attributes from the user interface using the corner cases (freq >
largest lpf supported by the part, respectively freq < smallest hpf
supported by the part). Moreover, in such case of bypassing the filter,
the input clock rate change might mess up things so we want to make sure
that it is disabled. Also, the feature will help emphasizing the filter
behavior, therefore adding it in the userspace will ease the
charcaterization of the filter's effects when active/disabled.
It was requested by users of the driver to ease the interaction with
different configuration modes of the device.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230731084928.8302-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BU27010 is an RGBC sensor with a flickering detection FIFO. The
RGBC+IR sensor functionality is largely similar to what the BU27008 has.
There are some notable things though:
- gain setting is once again new and exotic. Now, there is 6bit gain
setting where 4 of the bits are common to all channels and 2 bits
can be configured separately for each channel. The BU27010 has
similar "1X on other channels vs 2X on IR when selector is 0x0"
gain design as BU27008 had. So, we use same gain setting policy for
BU27010 as we did for BU27008 - driver sets same gain selector for all
channels but shows the gains separately for all channels so users
can (at least in theory) detect this 1X vs 2X madness...
- BU27010 has suffled all the control register bitfields to new
addresses and bit positions while still keeping the register naming
same.
- Some more power/reset control is added.
- FIFO for "flickering detection" is added.
The control register suffling made this slightly nasty. Still, it is
easier for maintenance perspective to add the BU27010 support in BU27008
driver because - even though the bit positions/addresses were changed -
most of the driver structure can be re-used. Writing own driver for
BU27010 would mean plenty of duplicate code albeit a tad more clarity.
The flickering FIFO is not supported by the driver.
Add BU27010 RGBC+IR support to rohm-bu27008 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/111cd217ccece1c1f16ab4287532dc4e1ddb8a3f.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BU27010 RGB + flickering sensor is in many regards similar to
the BU27008. Prepare for adding support for BU27010 by allowing
chip-specific properties to be brought from the of_device_id data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/d5994648033d5513993b8d72eb186ddda211b5ac.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MCP4728 is a 12-bit quad channel DAC with I2C interface.
support for:
* per-channel gain
* per-channel power state
* per-channel power down mode control
* per-channel vref selection internal/vdd
* store current state to on-chip EEPROM
Signed-off-by: Andrea Collamati <andrea.collamati@gmail.com>
Link: https://lore.kernel.org/r/a0933003ed3c855f9d80d6ce0a40add2b6f0ba36.1691066050.git.andrea.collamati@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add regulators for the VCC supplies of the admv1013.
The patch aims to align the implementation with the current admv1014
driver where all the VCC supplies are handled as regulators.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230731094455.26742-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230802120915.25631-1-aboutphysycs@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver, so it is redundant initialization to set
driver.owner in men_z188_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100938.100435-1-lizetao1@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fwnode_irq_get[_byname]() were changed to not return 0 anymore. The
special error case where device-tree based IRQ mapping fails can't no
longer be reliably detected from this return value. This yields a
functional change in the driver where the mapping failure is treated as
an error.
The mapping failure can occur for example when the device-tree IRQ
information translation call-back(s) (xlate) fail, IRQ domain is not
found, IRQ type conflicts, etc. In most cases this indicates an error in
the device-tree and special handling is not really required.
One more thing to note is that ACPI APIs do not return zero for any
failures so this special handling did only apply on device-tree based
systems.
Drop the special handling for DT mapping failures as these can no longer
be separated from other errors at driver side. Change all failures in
IRQ getting to be handled by continuing without the events instead of
aborting the probe upon certain errors.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/3ad1c6f195ead3dfa8711235e1dead139d27f700.1690890774.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no possible for platform_get_irq() to return 0
and the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230727131607.2897937-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data() and i2c_match_id() by i2c_get_match
_data() by making similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230723102743.102284-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace of_device_get_match_data() and i2c_match_id() by i2c_get_match
_data() by making similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230723105209.175545-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The `scripts/kernel-doc -v -none -Wall` reports several issues
with the kernel doc in IIO core C file. Update the comments
accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230724110204.46285-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Let the krealloc_array() copy the original data and
check for a multiplication overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230724110204.46285-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace device_get_match_data() and i2c_match_id() by i2c_get_match
_data() as we have similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230725171624.331283-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The struct cros_ec_command contains several integer fields and a
trailing array. An allocation size neglecting the integer fields can
lead to buffer overrun.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Yiyuan Guo <yguoaz@gmail.com>
Fixes: 974e6f02e2 ("iio: cros_ec_sensors_core: Add common functions for the ChromeOS EC Sensor Hub.")
Link: https://lore.kernel.org/r/20230630143719.1513906-1-yguoaz@gmail.com
Cc: <Stable@vger.kerenl.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no need to call the dev_err() function directly to print a custom
message when handling an error from either the platform_get_irq() or
platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230727073912.4178659-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The function lsm6dsx_get_acpi_mount_matrix should return an error when ACPI
support is not enabled to allow executing iio_read_mount_matrix in the
probe function.
Fixes: dc3d25f22b ("iio: imu: lsm6dsx: Add ACPI mount matrix retrieval")
Signed-off-by: Alejandro Tafalla <atafalla@dnyon.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20230714153132.27265-1-atafalla@dnyon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230714174628.4057920-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adis16477 devices support burst32 function, thus has_burst32
flag should be set to true.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230719123152.309624-3-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Murata IRS-D200 is a PIR sensor for human detection. It has support for
raw data measurements and detection event notification.
Add a driver with support for triggered buffer and events. Map the
various settings to the `iio` framework, e.g. threshold values, sampling
frequency, filter frequencies etc.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/d218a1bc75402b5ebd6e12a563f7315f83fe966c.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are devices (such as Murata IRS-D200 PIR proximity sensor) that
check the data signal with a running period. I.e. for a specified time,
they count the number of conditions that have occurred, and then signal
if that is more than a specified amount.
`IIO_EV_INFO_PERIOD` resets when the condition no longer is true and is
therefore not suitable for these devices. Add a new `iio_event_info`
`IIO_EV_INFO_RUNNING_PERIOD` that can be used as a running period. Also
add a new `IIO_EV_INFO_RUNNING_COUNT` that can be used to specify the
number of conditions that must occur during this running period.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/ee4a801ae9b9c4716c7bd23d8f79f232351df8bd.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
min() has strict type checking and preferred over min_t() for
unsigned types to avoid overflow. Here it's unclear why min_t()
was chosen since both variables are of the same type. In any
case update to use min().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable core clock at probe stage and disable it at remove stage.
Core clock is responsible for turning on/off the entire SoC module so
it should be on before the first module register is touched and be off
at very last moment.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230721102413.255726-2-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define and init voltage configuration bits. Those bits are inited in
vendor boot code (bl2, bl33) already so do it in the driver to not depend
on other code.
Introduced bits:
REG11[0] - selects Vref. 0 - calibration voltage, 1 - VDDA. txlx and later
SoCs support VDDA or calibration voltage as Vref, but others
support only calibration voltage. For newer platforms vendor
uses VDDA as default.
REG11[1] - reserved bit. g12a and later SoCs must write 1, others SoCs
write 0.
REG11[5] - Vref voltage. 0 - 0.9v, 1 - 1.8v. g12a and later SoCs must
write 0, others SoCs write 1.
REG11[6] - selects common-mode voltage, 0: from AVDD, 1: from Vref.
g12a and later SoCs must write 0, others SoCs write 1.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Disable internal continuous ring counter at init stage. Disable value
depends on SoC family: gxl and later SoCs write 1, others write 0.
This bit are inited in vendor boot code (bl2, bl33) already so do it
in the driver to not depend on other code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set up input channels 0,1 muxes in the same way as for the channels 2-7
later in the code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 813665564b ("iio: core: Convert to use firmware node handle
instead of OF node") switched the kind of nodes to use for label
retrieval in device registration. Probably an unwanted change in that
commit was that if the device has no parent then NULL pointer is
accessed. This is what happens in the stock IIO dummy driver when a
new entry is created in configfs:
# mkdir /sys/kernel/config/iio/devices/dummy/foo
BUG: kernel NULL pointer dereference, address: ...
...
Call Trace:
__iio_device_register
iio_dummy_probe
Since there seems to be no reason to make a parent device of an IIO
dummy device mandatory, let’s prevent the invalid memory access in
__iio_device_register when the parent device is NULL. With this
change, the IIO dummy driver works fine with configfs.
Fixes: 813665564b ("iio: core: Convert to use firmware node handle instead of OF node")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Milan Zamazal <mzamazal@redhat.com>
Link: https://lore.kernel.org/r/20230719083208.88149-1-mzamazal@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The regulator_get_voltage() function returns negative error codes.
This function saves it to an unsigned int and then does some range
checking and, since the error code falls outside the correct range,
it returns -EINVAL.
Beyond the messiness, this is bad because the regulator_get_voltage()
function can return -EPROBE_DEFER and it's important to propagate that
back properly so it can be handled.
Fixes: da35a7b526 ("iio: frequency: admv1013: add support for ADMV1013")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ce75aac3-2aba-4435-8419-02e59fdd862b@moroto.mountain
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230716175218.130557-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add IIO channel for all muxed inputs of channel 7.
Meson saradc channel 7 is connected to a mux that can switch input
to well-known sources like Vdd, GND and several Vdd dividers.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-7-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add channel labels to provide human-readable names for the inputs.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-6-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Channels could be referenced in the driver code and using enum allows
to make it more robust.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-5-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
meson_sar_adc_set_chan7_mux is a basic func() for writing single register,
defined as static. Moved it up so it could be used in more places.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Allow to use enum items for variables initialization.
For this, move enums upper in the code.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove IIO_CHAN_SOFT_TIMESTAMP channel because it's used only for
buffering mode which is not implemented.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds pressure compensation to the scd4x driver. The pressure can
be written to the sensor in hPa. The pressure will be compensated
internally by the sensor.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Link: https://lore.kernel.org/r/20230711101419.2065107-1-roan@protonic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In `iio_trigger_detach_poll_func()` the return value from
`trig->ops->set_trigger_state(trig, false)` is checked with `if (ret)`.
However, in `iio_trigger_attach_poll_func()` it is checked with
`if (ret < 0)`. Resolve this mismatch by only checking for `if (ret)` in
both places.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/pndv8eojdey.fsf@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable buffered reading of samples from the LMP92064 ADC.
The main benefit of this change is being able to read out current and
voltage measurements in a single transfer, allowing instantaneous power
measurements.
Reads into the buffer can be triggered by any software triggers, e.g.
the iio-trig-hrtimer:
$ mkdir /sys/kernel/config/iio/triggers/hrtimer/my-trigger
$ cat /sys/bus/iio/devices/iio\:device3/name
lmp92064
$ iio_readdev -t my-trigger -b 16 iio:device3 | hexdump
WARNING: High-speed mode not enabled
0000000 0000 0176 0101 0001 5507 abd5 7645 1768
0000010 0000 016d 0101 0001 ee1e ac6b 7645 1768
...
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230707063635.1496437-1-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704095808.33780-1-frank.li@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Even though it existed in bindings for the longest time,
ADC5_GPIO2_100K_PU was never assigned in the driver. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230627-topic-adc-v1-1-c61581abffa3@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace scnprintf with sysfs_emit_at which is the preferred alternative.
Also make sure each fractional digit is in its place by padding with
zeros up to 3 digits: "...%03d...".
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230620163135.93780-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check IIO_PROXIMITY with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DA217 accelerometer is another DA280 compatible accelerometer,
add its device-ids to the da280 driver.
Reported-by: Juno Computers USA <usa@junocomputers.com>
Tested-by: Juno Computers USA <usa@junocomputers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230613094346.162551-1-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace timestamping by the new common inv_sensors timestamp
module. The principle behind is the same but the implementation in
the new module is far better providing less jitter and a better
estimation.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create new inv_sensors common modules and move inv_icm42600
timestamp module inside. This module will be used by IMUs and
also in the future by other chips.
Modify inv_icm42600 driver to use timestamp module and do some
headers cleanup.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move icm42600 dependent function inside the core module.
Do some headers cleanup at the same time.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
power-sensor@40 {
compatible = "ti,ina232", "ti,ina231";
...
};
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Fixes: c43a102e67 ("iio: ina2xx: add support for TI INA2xx Power Monitors")
Link: https://lore.kernel.org/r/20230619141239.2257392-1-alvin@pqrs.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The intensity data from bu27008 is unsigned. The type of the scan data
was incorrectly marked as signed resulting large intensity values to be
interpreted as negative ones.
Fix the scan data type.
Fixes: 41ff93d14f ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/240a7ca5fc1b76da20d81f930d00f31a54b1fdf8.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ramona Gradinariu