Currently not all of the Port-specific capabilities listed in the
PORT_CMD-enumeration. Let's extend that set with the Cold Presence
Detection and Mechanical Presence Switch attached to the Port flags [1] so
to closeup the set of the platform-specific port-capabilities flags. Note
these flags are supposed to be set by the platform firmware if there is
one. Alternatively as we are about to do they can be set by means of the
OF properties.
While at it replace PORT_IRQ_DEV_ILCK with PORT_IRQ_DMPS and fix the
comment there. In accordance with [2] that IRQ flag is supposed to
indicate the state of the signal coming from the Mechanical Presence
Switch.
[1] Serial ATA AHCI 1.3.1 Specification, p.27
[2] Serial ATA AHCI 1.3.1 Specification, p.24, p.88
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
In case if the platform doesn't have BIOS or a comprehensive firmware
installed then the HBA capability flags will be left uninitialized. As a
good alternative we suggest to define the DT-properties with the AHCI
platform capabilities describing all the HW-init flags of the
corresponding capability register. Luckily there aren't too many of them.
SSS - Staggered Spin-up support and MPS - Mechanical Presence Switch
support determine the corresponding feature availability for the whole HBA
by means of the "hba-cap" property. Each port can have the "hba-port-cap"
property initialized indicating that the port supports some of the next
functionalities: HPCP - HotPlug capable port, MPSP - Mechanical Presence
Switch attached to a port, CPD - Cold Plug detection, ESP - External SATA
Port (eSATA), FBSCP - FIS-based switching capable port.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Currently the ACHI-platform library supports only the assert and deassert
reset signals and ignores the platforms with self-deasserting reset lines.
That prone to having the platforms with self-deasserting reset method
misbehaviour when it comes to resuming from sleep state after the clocks
have been fully disabled. For such cases the controller needs to be fully
reset all over after the reference clocks are enabled and stable,
otherwise the controller state machine might be in an undetermined state.
The best solution would be to auto-detect which reset method is supported
by the particular platform and use it implicitly in the framework of the
ahci_platform_enable_resources()/ahci_platform_disable_resources()
methods. Alas it can't be implemented due to the AHCI-platform library
already supporting the shared reset control lines. As [1] says in such
case we have to use only one of the next methods:
+ reset_control_assert()/reset_control_deassert();
+ reset_control_reset()/reset_control_rearm().
If the driver had an exclusive control over the reset lines we could have
been able to manipulate the lines with no much limitation and just used
the combination of the methods above to cover all the possible
reset-control cases. Since the shared reset control has already been
advertised and couldn't be changed with no risk to breaking the platforms
relying on it, we have no choice but to make the platform drivers to
determine which reset methods the platform reset system supports.
In order to implement both types of reset control support we suggest to
introduce the new AHCI-platform flag: AHCI_PLATFORM_RST_TRIGGER, which
when passed to the ahci_platform_get_resources() method together with the
AHCI_PLATFORM_GET_RESETS flag will indicate that the reset lines are
self-deasserting thus the reset_control_reset()/reset_control_rearm() will
be used to control the reset state. Otherwise the
reset_control_deassert()/reset_control_assert() methods will be utilized.
[1] Documentation/driver-api/reset.rst
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The ports-implemented property is mainly used on the OF-based platforms
with no ports mapping initialized by a bootloader/BIOS firmware. Seeing
the same of_property_read_u32()-based pattern has already been implemented
in the generic AHCI LLDD (glue) driver and in the Mediatek, St AHCI
drivers let's move the property read procedure to the generic
ahci_platform_get_resources() method. Thus we'll have the forced ports
mapping feature supported for each OF-based platform which requires that,
and stop re-implementing the same pattern in there a bit simplifying the
code.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.
Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
In order to simplify the clock-related code there is a way to convert the
current fixed clocks array into using the common bulk clocks kernel API
with dynamic set of the clock handlers and device-managed clock-resource
tracking. It's a bit tricky due to the complication coming from the
requirement to support the platforms (da850, spear13xx) with the
non-OF-based clock source, but still doable.
Before this modification there are two methods have been used to get the
clocks connected to an AHCI device: clk_get() - to get the very first
clock in the list and of_clk_get() - to get the rest of them. Basically
the platforms with non-OF-based clocks definition could specify only a
single reference clock source. The platforms with OF-hw clocks have been
luckier and could setup up to AHCI_MAX_CLKS clocks. Such semantic can be
retained with using devm_clk_bulk_get_all() to retrieve the clocks defined
via the DT firmware and devm_clk_get_optional() otherwise. In both cases
using the device-managed version of the methods will cause the automatic
resources deallocation on the AHCI device removal event. The only
complicated part in the suggested approach is the explicit allocation and
initialization of the clk_bulk_data structure instance for the non-OF
reference clocks. It's required in order to use the Bulk Clocks API for
the both denoted cases of the clocks definition.
Note aside with the clock-related code reduction and natural
simplification, there are several bonuses the suggested modification
provides. First of all the limitation of having no greater than
AHCI_MAX_CLKS clocks is now removed, since the devm_clk_bulk_get_all()
method will allocate as many reference clocks data descriptors as there
are clocks specified for the device. Secondly the clock names are
auto-detected. So the LLDD (glue) drivers can make sure that the required
clocks are specified just by checking the clock IDs in the clk_bulk_data
array. Thirdly using the handy Bulk Clocks kernel API improves the
clocks-handling code readability. And the last but not least this
modification implements a true optional clocks support to the
ahci_platform_get_resources() method. Indeed the previous clocks getting
procedure just stopped getting the clocks on any errors (aside from
non-critical -EPROBE_DEFER) in a way so the callee wasn't even informed
about abnormal loop termination. The new implementation lacks of such
problem. The ahci_platform_get_resources() will return an error code if
the corresponding clocks getting method ends execution abnormally.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Currently the IOMEM AHCI registers space is mapped by means of the
two functions invocation: platform_get_resource() is used to get the very
first memory resource and devm_ioremap_resource() is called to remap that
resource. Device-managed kernel API provides a handy wrapper to perform
the same in single function call: devm_platform_ioremap_resource().
While at it seeing many AHCI platform drivers rely on having the AHCI CSR
space marked with "ahci" name let's first try to find and remap the CSR
IO-mem with that name and only if it fails fallback to getting the very
first registers space platform resource.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The Broadcom SATA controller is obviously based on the AHCI standard. The
device driver uses the kernel AHCI library to work with it. Therefore we
can be have a more thorough DT-bindings evaluation by referring to the
AHCI-common schema instead of using the more relaxed SATA-common one.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The denoted in the description upper limit only concerns the Port
Multipliers, but not the actual SATA ports. It's an external device
attached to a SATA port in order to access more than one SATA-drive. So
when it's attached to a SATA port it just extends the port capability
while the number of actual SATA ports stays the same. For instance on AHCI
controllers the number of actual ports is determined by the CAP.NP field
and the PI (Ports Implemented) register. AFAICS in general the maximum
number of SATA ports depends on the particular controller implementation.
Generic AHCI controller can't have more than 32 ports (since CAP.NP is of
5 bits wide and PI register is 32-bits size), while DWC AHCI SATA
controller can't be configured with more than 8 ports activated. So let's
discard the SATA ports reg-property restrictions and just make sure that
it consists of a single reg-item.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Indeed in accordance with what is implemented in the AHCI platform driver
and the way the AHCI DT nodes are defined in the DT files we can add the
next AHCI DT properties constraints: AHCI CSR ID is fixed to 'ahci', PHY
name is fixed to 'sata-phy', AHCI controller can't have more than 32 ports
by design, AHCI controller can have up to 32 IRQ lines.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
In order to create a more sophisticated AHCI controller DT bindings let's
divide the already available generic AHCI platform YAML schema into the
platform part and a set of the common AHCI properties. The former part
will be used to evaluate the AHCI DT nodes mainly compatible with the
generic AHCI controller while the later schema will be used for more
thorough AHCI DT nodes description. For instance such YAML schemas design
will be useful for our DW AHCI SATA controller derivative with four clock
sources, two reset lines, one system controller reference and specific
max Rx/Tx DMA xfers size constraints.
Note the phys and target-supply property requirement is preserved in the
generic AHCI platform bindings because some platforms can lack of the
explicitly specified PHYs or target device power regulators.
Also note the SATA/AHCI ports properties have been moved to the
$defs-paragraph of the schemas. It's done in order to create the
extendable properties hierarchy such that particular AHCI-controller
could add vendor-specific port properties.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Seeing doubtfully any SATA device working without embedded DMA engine
let's permit the device nodes being equipped with the dma-coherent
property in case if the platform is capable of cache-coherent DMAs.
As a side-effect we can drop the explicit dma-coherent property definition
from the particular device schemas. Currently it concerns the Broadcom
SATA AHCI controller only.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
It is currently possible to select "Generic platform device PATA support"
in two situations:
- architecture allows the generic platform device PATA support and
indicates that with "select HAVE_PATA_PLATFORM".
- if the user claims to be an EXPERT by setting CONFIG_EXPERT to yes
However, there is no use case to have Generic platform device PATA support
in a kernel build if the architecture definition, i.e., the selection of
configs by an architecture, does not support it.
If the architecture definition is wrong, i.e., it just misses a 'select
HAVE_PATA_PLATFORM', then even an expert that configures the kernel build
should not just fix that by overruling the claimed support by an
architecture. If the architecture definition is wrong, the expert should
just provide a patch to correct the architecture definition instead---in
the end, if the user is an expert, sending a quick one-line patch should
not be an issue.
In other words, I do not see the deeper why an expert can overrule the
architecture definition in this case, as the expert may not overrule the
config selections defined by the architecture in the large majority
---or probably all other (modulo some mistakes)---of similar cases.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
There are two options for platform device PATA support:
PATA_PLATFORM: Generic platform device PATA support
PATA_OF_PLATFORM: OpenFirmware platform device PATA support
If an architecture allows the generic platform device PATA support, it
shall select HAVE_PATA_PLATFORM. Then, Generic platform device PATA support
is available and can be selected.
If an architecture has OpenFirmware support, which it indicates by
selecting OF, OpenFirmware platform device PATA support is available
and can be selected.
If OpenFirmware platform device PATA support is selected, then the
functionality (code files) from Generic platform device PATA support needs
to be integrated in the kernel build for the OpenFirmware platform device
PATA support to work. Select PATA_PLATFORM in PATA_OF_PLATFORM to make sure
the needed files are added in the build.
So, architectures with OpenFirmware support, do not need to additionally
select HAVE_PATA_PLATFORM. It is only needed by architecture that want the
non-OF pata-platform module.
Reflect this way of intended use of config symbols in the ata Kconfig and
adjust all architecture definitions.
This follows the suggestion from Arnd Bergmann (see Link).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/all/4b33bffc-2b6d-46b4-9f1d-d18e55975a5a@www.fastmail.com/
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
sata_scr_read() could return negative error code on failure. Check the
return value when reading the control register.
Signed-off-by: Li Zhong <floridsleeves@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Remove the repeated word "Transfer" in comments.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
There is unneeded word "to" in line 669, so remove it.
Signed-off-by: Shaomin Deng <dengshaomin@cdjrlc.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Since ata_build_rw_tf() is only called from ata_scsi_rw_xlat() with the
tf, dev and tag arguments obtained from the queued command structure,
we can simplify the interface of ata_build_rw_tf() by passing directly
the qc structure as argument.
Furthermore, since ata_scsi_rw_xlat() is never used for internal
commands, we can also remove the internal tag check for the NCQ case.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Rename ATA_DFLAG_NCQ_PRIO_ENABLE to ATA_DFLAG_NCQ_PRIO_ENABLED to match
the fact that this flags indicates if NCQ priority use is enabled by the
user.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Return value from ata_exec_internal() directly instead of
taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
The ACPI_FADT_LOW_POWER_S0 flag merely means that it is better to
use low-power S0 idle on the given platform than S3 (provided that
the latter is supported) and it doesn't preclude using either of
them (which of them will be used depends on the choices made by user
space).
For this reason, there is no benefit from checking that flag in
ahci_update_initial_lpm_policy().
First off, it cannot be a bug to do S3 with policy set to either
ATA_LPM_MIN_POWER_WITH_PARTIAL or ATA_LPM_MIN_POWER, because S3 can be
used on systems with ACPI_FADT_LOW_POWER_S0 set and it must work if
really supported, so the ACPI_FADT_LOW_POWER_S0 check is not needed to
protect the S3-capable systems from failing.
Second, suspend-to-idle can be carried out on a system with
ACPI_FADT_LOW_POWER_S0 unset and it is expected to work, so if setting
policy to either ATA_LPM_MIN_POWER_WITH_PARTIAL or ATA_LPM_MIN_POWER is
needed to handle that case correctly, it should be done regardless of
the ACPI_FADT_LOW_POWER_S0 value.
Accordingly, replace the ACPI_FADT_LOW_POWER_S0 check in
ahci_update_initial_lpm_policy() with pm_suspend_default_s2idle()
which is more general and also takes the user's preference into
account and drop the CONFIG_ACPI #ifdef around it that is not necessary
any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
ata_dev_set_feature() is currently used for enabling/disabling any ATA
feature, e.g. SETFEATURES_SPINUP and SETFEATURE_SENSE_DATA, i.e. it is
not only used to enable/disable SATA specific features.
For most features, the enable/disable bit is specified in the subcommand
specific field "count".
It is only for the specific subcommands "Enable SATA feature" (0x10) and
"Disable SATA feature" (0x90) where the field "count" is used to specify
a feature instead of enable/disable. The parameter names for this
function are thus quite misleading.
Rename the parameter names to be more generic and in line with ACS-5,
and remove the references to "SATA FEATURES" in the kernel-doc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Printing the timeout value may help in troubleshooting failures.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.
Fixes powerpc allmodconfig build:
In file included from include/linux/nodemask.h:97,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:7,
from include/linux/radix-tree.h:12,
from include/linux/idr.h:15,
from include/linux/kernfs.h:12,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/pci.h:35,
from arch/powerpc/kernel/prom_init.c:24:
include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
| ^~~~~~~~~~~~~~
| add_latent_entropy
include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
somebody left NULL ->proc_lseek, became a practical issue now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYvlK4QAKCRBZ7Krx/gZQ
68EUAQDFUFhyvVLnhh1tAkPt3mxHT2OHASN8z6gRBjxGmqj53QD8D4EZAMy3XHnB
/6ajdD7hl5pxZQnECPqbBjzPYHa22QE=
=BNbv
-----END PGP SIGNATURE-----
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs lseek fix from Al Viro:
"Fix proc_reg_llseek() breakage. Always had been possible if somebody
left NULL ->proc_lseek, became a practical issue now"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
take care to handle NULL ->proc_lseek()
Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.
Fixes: 868941b144 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYvi0yQAKCRCAXGG7T9hj
vmikAQDWSrcWuxDkGnzut0A1tBQRUCWDMyKPqigWAA5tH2sPgAEAtWfBvT1xyl7T
gZ22I7o21WxxDGyvNUcA65pK7c2cpg8=
=UMbq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- fix the handling of the "persistent grants" feature negotiation
between Xen blkfront and Xen blkback drivers
- a cleanup of xen.config and adding xen.config to Xen section in
MAINTAINERS
- support HVMOP_set_evtchn_upcall_vector, which is more compliant to
"normal" interrupt handling than the global callback used up to now
- further small cleanups
* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
xen: remove XEN_SCRUB_PAGES in xen.config
xen/pciback: Fix comment typo
xen/xenbus: fix return type in xenbus_file_read()
xen-blkfront: Apply 'feature_persistent' parameter when connect
xen-blkback: Apply 'feature_persistent' parameter when connect
xen-blkback: fix persistent grants negotiation
x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
- 'perf c2c' now supports ARM64, adjust its output to cope with differences with
what is in x86_64. Now go find false sharing on ARM64 (at least Neoverse) as well!
- Refactor the JSON processing, making the output more compact and thus reducing the
size of the resulting perf binary.
- Improvements for 'perf offcpu' profiling, including tracking child processes.
- Update Intel JSON metrics and events files for broadwellde, broadwellx,
cascadelakex, haswellx, icelakex, ivytown, jaketown, knightslanding,
sapphirerapids, skylakex and snowridgex.
- Add 'perf stat' JSON output and a 'perf test' entry for it.
- Ignore memfd and anonymous mmap events if jitdump present.
- Refactor 'perf test' shell tests allowing subdirs.
- Fix an error handling path in 'parse_perf_probe_command()'
- Fixes for the guest Intel PT tracing patchkit in the 1st batch of this merge window.
- Print debuginfod queries if -v option is used, to explain delays in processing when
debuginfo servers are enabled to fetch DSOs with richer symbol tables.
- Improve error message for 'perf record -p not_existing_pid'
- Fix openssl and libbpf feature detection.
- Add PMU pai_crypto event description for IBM z16 on 'perf list'.
- Fix typos and duplicated words on comments in various places.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYvg1aQAKCRCyPKLppCJ+
J12hAQCCBXh+t7ab2PyXqDDwr/1aFc94nXA2A5wQ9N4MzD66YgEA1O34rxBiyetU
c1pStjrOqR6HGlXh+jAI4zTnK6w1wAs=
=m+oE
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tool updates from Arnaldo Carvalho de Melo:
- 'perf c2c' now supports ARM64, adjust its output to cope with
differences with what is in x86_64. Now go find false sharing on
ARM64 (at least Neoverse) as well!
- Refactor the JSON processing, making the output more compact and thus
reducing the size of the resulting perf binary
- Improvements for 'perf offcpu' profiling, including tracking child
processes
- Update Intel JSON metrics and events files for broadwellde,
broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
knightslanding, sapphirerapids, skylakex and snowridgex
- Add 'perf stat' JSON output and a 'perf test' entry for it
- Ignore memfd and anonymous mmap events if jitdump present
- Refactor 'perf test' shell tests allowing subdirs
- Fix an error handling path in 'parse_perf_probe_command()'
- Fixes for the guest Intel PT tracing patchkit in the 1st batch of
this merge window
- Print debuginfod queries if -v option is used, to explain delays in
processing when debuginfo servers are enabled to fetch DSOs with
richer symbol tables
- Improve error message for 'perf record -p not_existing_pid'
- Fix openssl and libbpf feature detection
- Add PMU pai_crypto event description for IBM z16 on 'perf list'
- Fix typos and duplicated words on comments in various places
* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
perf test: Refactor shell tests allowing subdirs
perf vendor events: Update events for snowridgex
perf vendor events: Update events and metrics for skylakex
perf vendor events: Update metrics for sapphirerapids
perf vendor events: Update events for knightslanding
perf vendor events: Update metrics for jaketown
perf vendor events: Update metrics for ivytown
perf vendor events: Update events and metrics for icelakex
perf vendor events: Update events and metrics for haswellx
perf vendor events: Update events and metrics for cascadelakex
perf vendor events: Update events and metrics for broadwellx
perf vendor events: Update metrics for broadwellde
perf jevents: Fold strings optimization
perf jevents: Compress the pmu_events_table
perf metrics: Copy entire pmu_event in find metric
perf pmu-events: Hide the pmu_events
perf pmu-events: Don't assume pmu_event is an array
perf pmu-events: Move test events/metrics to JSON
perf test: Use full metric resolution
perf pmu-events: Hide pmu_events_map
...
- Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit CPUs trap on it
rather than ignoring it as they should.
- Fix ftrace when building with clang, which was broken by some refactoring.
- A couple of other minor fixes.
Thanks to: Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej Mosnacek, Pali Rohár,
Russell Currey Segher Boessenkool.
-----BEGIN PGP SIGNATURE-----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=SpYx
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
CPUs trap on it rather than ignoring it as they should.
- Fix ftrace when building with clang, which was broken by some
refactoring.
- A couple of other minor fixes.
Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.
* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix build failure from uninitialised variable
powerpc/ppc-opcode: Fix PPC_RAW_TW()
powerpc64/ftrace: Fix ftrace for clang builds
powerpc: Make eh value more explicit when using lwarx
powerpc: Don't hide eh field of lwarx behind a macro
powerpc: Fix eh field when calling lwarx on PPC32
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYvg//wAKCRBZ7Krx/gZQ
631TAP92pf2EYSUbWRjSshaxYrIJeiDpIBBikSoEOQj4GG4hUwD/U6f/LnFW0a8P
58kXaxXI9cNBEVRhwI/dZKW9q/WxBAY=
=3rHw
-----END PGP SIGNATURE-----
Merge tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull /proc/mounts fix from Al Viro:
"Fix for /proc/mounts escaping - escape the '#' character too"
* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: escape hash as well
-----BEGIN PGP SIGNATURE-----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=gZTH
-----END PGP SIGNATURE-----
Merge tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
- two fixes for stable, one for a lock length miscalculation, and
another fixes a lease break timeout bug
- improvement to handle leases, allows the close timeout to be
configured more safely
- five restructuring/cleanup patches
* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
cifs: Add constructor/destructors for tcon->cfid
SMB3: fix lease break timeout when multiple deferred close handles for the same file.
smb3: allow deferred close timeout to be configurable
cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
cifs: Move cached-dir functions into a separate file
cifs: Remove {cifs,nfs}_fscache_release_page()
cifs: fix lock length calculation
Enable multipage folio support for the afs filesystem.
Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.
Note that it does require a change to afs_write_begin() to return the
correct subpage. This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix a potential use-after-free bug in posix timers
- correct a prototype
- address a build warning
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQJFBAABCgAvFiEEBpT5eoXrXCwVQwEKEnMQ0APhK1gFAmL3epQRHG1pbmdvQGtl
cm5lbC5vcmcACgkQEnMQ0APhK1iPZw/+I/9GXcf3SzbG5M6Nf21SJpSjC4hAHHgb
eyv5MUNxKvCHU5iT2SrCvgKjESl5I/E70kubeRHJnvarBPUzGnHHzGlYIYOaJPQ7
irJpUj/6R8ps4UsMBJ8vj5f3b7163zhBJVP8egDW6roT1HUrYTFeIjIli/SOCxpY
H1/DqHlbEALE5o5xykg3zuqAbywym+hNRleIVls4wqjZNnfqiTElSuW9xqw9xt3n
9xYmOKZaztdv5Lp2JCm7QOu2byGzeHje72ppsDcBZ3EBvHUBLSndhfe5NQUGhtxy
UlBqAELA653uPgPnNKLRMqt/kop8emHqvAx8T0RawPwoUS6XGDVxRX+my8+HKklg
P8KsM/8W7+3KTHz0bf72DEHTFiXCzlswRzdOSvP5bR4xw1G4ychzvuxAiPDFR3zT
v7uPgykxxCrEexVCBCdPmrl4WikwLJtcrSXtJ4bsisxQFlq7WWd2/osZkTffI3pN
IIxDXuHFHC78lrUMk2OQ+ITBz01z4nCFSlgMGZ6ZY6ppS1Rndy1HG/B2NgjW1zGP
Y/1xq/nWaql0QO7RmyoJXt1ZSMJYCyKFocRDh9nBmtBSlYm3A8aIA8b4i1VRRG1G
8HOkdS8ef2eOWj8wqk0NvoTbiGjV7YM5pf0g1dmRLA+aGCBD1P9/iFcBv5b6Uxaq
qZ7ZtuQzsyc=
=Plg8
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc timer fixes:
- fix a potential use-after-free bug in posix timers
- correct a prototype
- address a build warning"
* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Cleanup CPU timers before freeing them during exec
time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
posix-timers: Make do_clock_gettime() static
(not turned on by default), which also need STIBP enabled (if
available) to be '100% safe' on even the shortest speculation
windows.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ac6x
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
turned on by default), which also need STIBP enabled (if available) to
be '100% safe' on even the shortest speculation windows"
* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Enable STIBP for IBPB mitigated RETBleed
and NTB EndPoint Function (EPF) support and the various fixes from that
being in -next for Linux v5.20
-----BEGIN PGP SIGNATURE-----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=DAah
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.20' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
- Return error codes from block device flushes to userspace.
- Fix a deadlock between reclaim and mount time quotacheck.
- Fix an unnecessary ENOSPC return when doing COW on a filesystem with
severe free space fragmentation.
- Fix a miscalculation in the transaction reservation computations for
file removal operations.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----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=wFgu
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull more xfs updates from Darrick Wong:
"There's not a lot this time around, just the usual bug fixes and
corrections for missing error returns.
- Return error codes from block device flushes to userspace
- Fix a deadlock between reclaim and mount time quotacheck
- Fix an unnecessary ENOSPC return when doing COW on a filesystem
with severe free space fragmentation
- Fix a miscalculation in the transaction reservation computations
for file removal operations"
* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix inode reservation space for removing transaction
xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
xfs: fix intermittent hang during quotacheck
xfs: check return codes when flushing block devices
Mostly small bug fixes and trivial updates. The major new core update
is a change to the way device, target and host reference counting is
done to try to make it more robust (this change has soaked for a while
to try to winkle out any bugs).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYveemSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisheaiAP9DPQ70
7hEdak6evXUwlWwlVBvEFAfZlzpHN+uNzUCvpgD+N61RSPhHV1hXu12sVMmjMNEb
pow+ee47Mc0t/OO68jA=
=1yQh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes and trivial updates.
The major new core update is a change to the way device, target and
host reference counting is done to try to make it more robust (this
change has soaked for a while to try to winkle out any bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm8001: Fix typo 'the the' in comment
scsi: megaraid_sas: Remove redundant variable cmd_type
scsi: FlashPoint: Remove redundant variable bm_int_st
scsi: zfcp: Fix missing auto port scan and thus missing target ports
scsi: core: Call blk_mq_free_tag_set() earlier
scsi: core: Simplify LLD module reference counting
scsi: core: Make sure that hosts outlive targets
scsi: core: Make sure that targets outlive devices
scsi: ufs: ufs-pci: Correct check for RESET DSM
scsi: target: core: De-RCU of se_lun and se_lun acl
scsi: target: core: Fix race during ACL removal
scsi: ufs: core: Correct ufshcd_shutdown() flow
scsi: ufs: core: Increase the maximum data buffer size
scsi: lpfc: Check the return value of alloc_workqueue()
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmL2SxQQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpl24D/4nxPDuhvDxLHpMUR/C2lCtAnqVhHtGLhIX
QSw+GVA5LuJvuB0L5Zr7ODDILPY5ZyWI/F1FPVJUOJE1NJ3tFiH4WzFIkqtFtVCE
2jFTXH63A/o/fyo9nscsZ1g6eEswSAbvenHEa9HNpjgFxz0lnXjrniP5VFPo5HNl
F8/MO1CBkKmhsGazZn7o1J3Ws6RvApq59YzxHmVz1hFHPgJFN2KwIAQjY2+GGoOD
ifpRBbZBCTzj2dEEFZHeK1aCYhTNP4VqbNnBDQPZHwEB3qkml5R9GhTlUe7Ej17t
7o4A05efcm/24TXcODMHP5YaGA14otPUr8wQiJjuOIFLw8sMC61OyS9qDdu1IvyW
JCnTtDkzwZZEkhXlraU1HmiLSaBjMEvd/2puxbcS9kISdO7baCLd4Oj7+8ThVhIf
JHIt2x3vzKaCzWI93IMrw5iJFK0+NS+SLAD6eyuEgC71Rj5ooemxrBYxKBQ7jb3o
GCC3SaU8lFmB1Z/zKo63gGS1b7eaCNGauNm9/gSe1jM8Sor4hlT0yeNRpHf7egAu
1dUQdSwgon6EH6JOGX3CFSC9lnIEAew733QZLaYBqar2WHcq5Wpq6LcWUHhhujgB
dSTeLY1Tnhs3GWvMFe4JH/YZilFpbMKzxuFPCV7sQScxzlaGusliX8kVkha/VPLK
9rtT8uyJXg==
=1/w+
-----END PGP SIGNATURE-----
Merge tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request
- print nvme connect Linux error codes properly (Amit Engel)
- fix the fc_appid_store return value (Christoph Hellwig)
- fix a typo in an error message (Christophe JAILLET)
- add another non-unique identifier quirk (Dennis P. Kliem)
- check if the queue is allocated before stopping it in nvme-tcp
(Maurizio Lombardi)
- restart admin queue if the caller needs to restart queue in
nvme-fc (Ming Lei)
- use kmemdup instead of kmalloc + memcpy in nvme-auth (Zhang
Xiaoxu)
- __alloc_disk_node() error handling fix (Rafael)
* tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block:
block: Do not call blk_put_queue() if gendisk allocation fails
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S70
nvme-tcp: check if the queue is allocated before stopping it
nvme-fabrics: Fix a typo in an error message
nvme-fabrics: parse nvme connect Linux error codes
nvmet-auth: use kmemdup instead of kmalloc + memcpy
nvme-fc: fix the fc_appid_store return value
nvme-fc: restart admin queue if the caller needs to restart queue
-----BEGIN PGP SIGNATURE-----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=FfLf
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Regression fix for this merge window, fixing a wrong order of
arguments for io_req_set_res() for passthru (Dylan)
- Fix for the audit code leaking context memory (Peilin)
- Ensure that provided buffers are memcg accounted (Pavel)
- Correctly handle short zero-copy sends (Pavel)
- Sparse warning fixes for the recvmsg multishot command (Dylan)
- Error handling fix for passthru (Anuj)
- Remove randomization of struct kiocb fields, to avoid it growing in
size if re-arranged in such a fashion that it grows more holes or
padding (Keith, Linus)
- Small series improving type safety of the sqe fields (Stefan)
* tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block:
io_uring: add missing BUILD_BUG_ON() checks for new io_uring_sqe fields
io_uring: make io_kiocb_to_cmd() typesafe
fs: don't randomize struct kiocb fields
io_uring: consistently make use of io_notif_to_data()
io_uring: fix error handling for io_uring_cmd
io_uring: fix io_recvmsg_prep_multishot sparse warnings
io_uring/net: send retry for zerocopy
io_uring: mem-account pbuf buckets
audit, io_uring, io-wq: Fix memory leak in io_sq_thread() and io_wqe_worker()
io_uring: pass correct parameters to io_req_set_res
This is a prelude to adding more tests to shell tests and in order to
support putting those tests into subdirectories, I need to change the
test code that scans/finds and runs them.
To support subdirs I have to recurse so it's time to refactor the code
to allow this and centralize the shell script finding into one location
and only one single scan that builds a list of all the found tests in
memory instead of it being duplicated in 3 places.
This code also optimizes things like knowing the max width of desciption
strings (as we can do that while we scan instead of a whole new pass of
opening files).
It also more cleanly filters scripts to see only *.sh files thus
skipping random other files in directories like *~ backup files, other
random junk/data files that may appear and the scripts must be
executable to make the cut (this ensures the script lib dir is not seen
as scripts to run).
This avoids perf test running previous older versions of test scripts
that are editor backup files as well as skipping perf.data files that
may appear and so on.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight@lists.linaro.org
Link: https://lore.kernel.org/r/20220812121641.336465-2-carsten.haitzler@foss.arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update the events to v1.20, update events for snowridgex by the latest
event converter tools.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the snowridgex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-12-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update the events to v1.28, the metrics are based on TMA 4.4 full, update
events and metrics for skylakex by the latest event converter tools.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the skylakex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-11-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
sapphirerapids.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the sapphirerapids files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-10-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update the events to v9, update events for knightslanding by the latest
event converter tools.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the knightslanding files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-9-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
jaketown.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the jaketown files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-8-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
ivytown.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the ivytown files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-7-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Update the events to v1.15, the metrics are based on TMA 4.4 full, update
events and metrics for icelakex by the latest event converter tools.
Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py
to download and generate the latest events and metrics. Manually copy
the icelakex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-6-zhengjun.xing@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
