Use the newly introduce iio_push_to_buffers_with_ts_unaligned() function
to ensure a bounce buffer is used to provide the required alignment and
space padding needed by the IIO core which requires the timestamp
is naturally aligned. There will be a performance cost to this change
but it will ensure the driver works on platforms that do not support
unaligned 8 byte assignments, and with consumer drivers that may
assume natural alignment of the timestamp.
Issue found as part of an audit of all calls to
iio_push_to_buffers_with_timestamp()
Fixes: 7e87d11c9b ("iio: adc: Add support for TI ADC108S102 and ADC128S102")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20210613151039.569883-3-jic23@kernel.org
This is a simple conversion for to device-managed with using
devm_request_threaded_irq(), disabling the regulator via a
devm_add_action_or_reset() hook and finally using
devm_iio_device_register().
The i2c_set_clientdata() call is removed as it becomes redundant after this
change.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926194315.7742-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Otherwise most build checks will omit this driver from a compile-test due
to it's dependency only on the BERLIN_ARCH symbol.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926192642.4051329-2-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver requires only a devm_add_action_or_reset() hook for the
power-down of the device, and then devm_iio_device_register() can be used
directly.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926192642.4051329-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver already hooks a similar unwind callback via
devm_add_action_or_reset().
They pretty much do the same thing, so this change converts it to the
devm_iio_map_array_register().
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20210926162859.3567685-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For this conversion, the 2 regulators (being enabled) require each a
devm_add_action_or_reset() hook registration.
For the other functions, there are device-managed variants.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210926162110.3536436-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a trivial conversion to device-managed functions.
The mutex_destroy() calls are redundant, as the data will be free'd anyway.
And the IRQ and IIO register functions both have device-managed
equivalents.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210926154932.3287590-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903072917.45769-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903072917.45769-5-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the probe of this driver to use device-managed
functions only, which means that the remove hook can be removed.
The remove hook has only 2 calls to iio_device_unregister() and
iio_map_array_unregister(). Both these can now be done via devm register
functions, now that there's also a devm_iio_map_array_register() function.
The platform_set_drvdata() can also be removed now.
This change also removes the error print for when the iio_device_register()
call fails. This isn't required now.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903072917.45769-4-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The only call in the remove hook is the iio_map_array_unregister() call.
Since we have a devm_iio_map_array_register() function now, we can use that
and remove the remove hook entirely.
The IIO device was registered with the devm_iio_device_register() prior to
this change.
Also, the platform_set_drvdata() can be removed now, since it was used only
in the remove hook.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210903072917.45769-3-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver tries to initialize all possible regulators from the DT, then
match the external regulators with each channel and then release all unused
regulators.
We can change the logic a bit to initialize regulators only when at least
one channel needs them.
This change creates a mx25_gcq_ext_regulator_setup() function that is
called only for the external regulators. If there's already a reference to
an external regulator, the function will just exit early with no error.
This way, the driver doesn't need to keep any track of these regulators
during init.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210625074325.9237-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
External triggers do not necessarily need the EOC interrupt to be
populated to work properly. The end of conversion status may either come
from an interrupt or from a sufficient enough extra delay. IRQs are not
mandatory so move the triggered buffer setup out of the IRQ condition
and add the logic to wait enough time for all the requested conversions
to be in the device's FIFO.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-17-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no reason to limit this driver to its internal trigger. The
only difference being, when using an external trigger, the sample
conversion must be manually started.
Drop the ->validate_trigger() hook in order to allow other triggers to
be bound.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-16-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
So far the End-Of-Conversion interrupt was only used in conjunction with
the internal trigger to process the data. Let's extend the use of this
interrupt handler to support regular single-shot conversions as well.
Doing so requires writing our own hard IRQ handler. This handler has to
check if buffers are enabled or not:
*** Buffers disabled condition ***
This means the user requested a single conversion and the sample is
ready to be retrieved.
-> This implies adding the relevant completion boilerplate.
*** Buffers enabled condition ***
Triggers are used. So far there is only support for the internal
trigger but this trigger might soon be attached to another device as
well so it is the core duty to decide which handler to call in order
to process the data. The core will decide to either:
* Call the internal trigger handler which will extract the data that
is already present in the ADC FIFOs
or
* Call the trigger handler of another driver when using this trigger
with another device, even though this call will be slightly delayed
by the fact that the max1027 IRQ is a data-ready interrupt rather
than a real trigger:
-> The new handler will manually inform the core about the trigger
having transitioned by directly calling iio_trigger_poll() (which
iio_trigger_generic_data_rdy_poll() initially did).
In order for the handler to be "source" agnostic, we also need to change
the private pointer and provide the IIO device instead of the trigger
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-15-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The threaded handler is not populated, this means there is nothing
running in process context so let's switch to the regular
devm_request_irq() call instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-14-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For now this helper only waits for the maximum duration of a single
conversion.
In practice, a "temperature measurement" will take twice this
time because it will also carry another analog conversion but as here we
will only care about the temperature conversion which happens first, we
can still only wait for a single sample and get the right data.
This helper will soon be improved to properly handle the end of
conversion interrupt as well as a higher number of samples.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Create a max1027_read_scan() helper which will make clearer the future IRQ
handler updates (no functional change).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-12-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When hardware buffers are enabled (the cnvst pin being the trigger), one
should not mess with the device state by requesting a single channel
read.
There is already a iio_buffer_enabled() check in *_read_single_value()
to merely prevent this situation but the check is inconsistent since
buffers can be enabled after the if clause anyway. Instead, use the core
mutex by calling iio_device_claim/release_direct_mode().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-11-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We don't expect the (hardware) cnvst trigger to be enabled at boot time,
this is a user choice made in sysfs and there is a dedicated callback to
enable/disable this trigger. Hence, we can just ensure it is disabled in
the probe at initialization time and then assume that whenever a
->read_raw() call happens, the trigger has been disabled and conversions
will start on register write.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-9-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The call to max1027_enable_trigger() is the same in both cases thanks to
the 'state' variable, so factorize a little bit to simplify the code and
explain why we call this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-8-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are two ways to physically trigger a conversion:
- A falling edge on the cnvst pin
- A write operation on the conversion register
Let's create a helper for this.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-7-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it clear that the *_set_trigger_state() hook is responsible for
cnvst based conversions by renaming the helper. This may avoid
confusions with software trigger support that is going to be
introduced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-6-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.
The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.
For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.
Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Memory allocation errors automatically trigger the right logs, no need
to have our own.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210921115408.66711-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow checkpatch.pl's main advices before hacking into the driver, mainly:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
WARNING: Prefer 'unsigned int *' to bare use of 'unsigned *'
CHECK: Comparison to NULL could be written "!foo"
CHECK: Alignment should match open parenthesis
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add
driver support for this ADC.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a compensation phase to improve the accuracy of ADC
measurement. This is the built-in function through input half of the
reference voltage to get the ADC offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the function to set the sampling rate and keep the sampling period
for a driver used to wait the fresh value.
In addition, since the ADC clock is required when initializing the ADC
device, move clk_prepare_enable ahead of the initialization phase.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make driver to support ast2600 adc device.
- Use shared reset controller
- Complete the vref configure function
- Add the model data for ast2600 adc
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch uses need_prescaler and scaler_bit_width to set the ADC clock
scaler.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sync if statement with the actual warning.
Fixes: 9504db5765 ("iio: adc: tsc2046: fix a warning message in tsc2046_adc_update_scan_mode()")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007093007.1466-2-o.rempel@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105631.1474-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105646.1576-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The previous driver does't apply the necessary scaling to take the
voltage range into account.
We change readback value from raw data to input voltage to fix case
IIO_CHAN_INFO_PROCESSED.
Fixes: ace4cdfe67 ("iio: adc: mt2701: Add Mediatek auxadc driver for mt2701.")
Signed-off-by: Hui Liu <hui.liu@mediatek.com>
Link: https://lore.kernel.org/r/20210926073028.11045-2-hui.liu@mediatek.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add clk_disable_unprepare() on error path in rzg2l_adc_pm_runtime_resume().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210819132416.175644-1-yangyingliang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The macro MAX1X29_CHANNELS() already calls MAX1X27_CHANNELS().
Calling MAX1X27_CHANNELS() before MAX1X29_CHANNELS() in the definition
of MAX1X31_CHANNELS() declares the first 8 channels twice. So drop this
extra call from the MAX1X31 channels list definition.
Fixes: 7af5257d84 ("iio: adc: max1027: Prepare the introduction of different resolutions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-3-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
10-bit devices must shift the value twice.
This is not needed anymore on 12-bit devices.
Fixes: ae47d009b5 ("iio: adc: max1027: Introduce 12-bit devices support")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210818111139.330636-2-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A successful 'regulator_enable()' call should be balanced by a
corresponding 'regulator_disable()' call in the error handling path of the
probe, as already done in the remove function.
Update the error handling path accordingly.
Fixes: 913b864686 ("iio: adc: Add TI ADC128S052")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/85189f1cfcf6f5f7b42d8730966f2a074b07b5f5.1629542160.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently when a timeout occurs in rzg2l_adc_hw_init the error -EBUSY is
assigned to ret but the error code is used as the function is hard-coded
to return 0. The variable ret is 0 before entering the while-loop hence
the fix is just to return ret at the end of the function to return the
success 0 or -EBUSY return code.
Addresses-Coverity: ("Unused value")
Fixes: d484c21bac ("iio: adc: Add driver for Renesas RZ/G2L A/D converter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210817172111.495897-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch completes the declare of ADC register bitfields and uses the
same prefix ASPEED_ADC_* for these bitfields. In addition, tidy up space
alignment of the codes.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210831071458.2334-4-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change converts the driver to register via devm_iio_device_register().
The regulator disable is moved on a devm_add_action_or_reset() hook.
And the spi_set_drvdata() isn't required anymore.
And finally, the ads8344_remove() can be removed as well.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210903073707.46892-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update copyright and authors information (corrected e-mail address), and
add myself as one of the authors.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-9-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to sama7g5 ADC which is similar with sama5d2/sam9x60 device.
Differences are highlighted by compatible.
Main differences include 16 channels instead of 12 and missing
resistive touchscreen.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-8-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add helper for the COR register. This helper allows to modify the COR
register, removes duplicate code and improves readability.
The COR offset is now part of the register layout. This will allow
different platform with a different offset to use the same helper.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-7-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some platforms have separated the end-of-conversion information from the
usual ISR/IMR/IER/IDR registers, into EOC_ISR/EOC_IMR/EOC_IER/EOC_IDR.
To cope with both variants, helpers are being added, that will make
code more clear and more easy to read.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-6-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the driver to platform specific structures. This means:
- create a register layout struct that will hold offsets for registers
- create a platform struct that will hold platform information (number of
channels, indexes for different channels and pointer to layout struct)
- convert specific macros that are platform dependent into platform variables
This step is in fact a no-op, but allows the driver to be more flexible
and for future enhancement including adding new platforms that are partly
compatible with the current driver and differ slightly in register layout
or capabilities for example.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-5-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hw_init hardware init call must happen after the clock is prepared and
enabled. Otherwise, writing to the registers might lead to a block or
external abort.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-3-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch to devm_iio_device_register to finalize devm migration.
This removes the use for iio_device_unregister() and since
mutex_destroy() is not necessary here, remove it altogether.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-6-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for selecting the voltage reference from the devicetree.
This change is required to get valid readings with all three
vref hardware configurations supported by the ADC.
For instance if the ADC isn't provided with an external reference,
the sample request must specify an internal voltage reference to get a
valid reading.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports devices with 14-bit and 16-bit sample sizes.
This implies different SPI transfer lengths which are not always handled
properly by some SPI controllers.
To work around this limitation, define a big endian buffer used to split
the buffer into two 8-bit messages in the event that the controller
doesn't support 14-bit or 16-bit transfers.
A separate buffer is introduced here to avoid performing operations on
types of different endianness.
Since all transfers use the same bits_per_word value, move that logic to
the probe function, and let transfers default to the value defined in
the struct spi_device.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-3-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had been
maintained out-of-tree by Larry with the end goal of actually being able
to get this driver out of staging eventually. Despite that driver being
"newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to see,
that is why there are additions to the mfc and misc driver subsystems.
All of these were acked by the various subsystem maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS+BKg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yku5gCgyMykJ2mwtEiQxfAWu13e2iZX29AAnjk38ANp
Un2sQXYnL9RVlcnjLg+X
=jMWL
-----END PGP SIGNATURE-----
Merge tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO and staging driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had
been maintained out-of-tree by Larry with the end goal of actually
being able to get this driver out of staging eventually. Despite that
driver being "newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to
see, that is why there are additions to the mfc and misc driver
subsystems. All of these were acked by the various subsystem
maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems"
[ Note: the r8188eu merge clashed with commit 89939e8906 ("staging:
rtlwifi: use siocdevprivate") from the networking tree. When resolving
the issue, I noted that the whole r8188eu rtw_android code is dead
since commit ae7471cae0 ("staging: r8188eu: remove rtw_ioctl
function").
End result: the merge resolution was to throw all of that away,
rather than do the mindless fixup to code that isn't actually
reachable - Linus ]
* tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (551 commits)
staging: vt6655: Remove filenames in files
staging: r8188eu: add extra TODO entries
staging: vt6656: Remove filenames in files
staging: wlan-ng: fix invalid assignment warning
staging: r8188eu: rename fields of struct rtl_ps
staging: r8188eu: remove ODM_DynamicPrimaryCCA_DupRTS()
staging: r8188eu: rename fields of struct dyn_primary_cca
staging: r8188eu: rename struct field Wifi_Error_Status
staging: r8188eu: Provide a TODO file for this driver
staging: r8188eu: remove unneeded variable
staging: r8188eu: remove unneeded conversions to bool
staging: r8188eu: remove {read,write}_macreg
staging: r8188eu: core: remove condition with no effect
staging: r8188eu: remove ethernet.h header file
staging: r8188eu: remove ip.h header file
staging: r8188eu: remove if_ether.h header file
staging: r8188eu: make rtw_deinit_intf_priv return void
staging: r8188eu: use is_multicast_ether_addr in os_dep/recv_linux.c
staging: r8188eu: use is_multicast_ether_addr in hal/rtl8188eu_xmit.c
staging: r8188eu: use is_multicast_ether_addr in core/rtw_xmit.c
...
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
-----BEGIN PGP SIGNATURE-----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=d/Fm
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd set of new IIO device support and cleanups for the 5.15 cycle.
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
* tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: Add driver for Renesas RZ/G2L A/D converter
dt-bindings: iio: adc: Add binding documentation for Renesas RZ/G2L A/D converter
iio: pressure: hp03: update device probe to register with devm functions
iio: adc: rockchip_saradc: add voltage notifier so get referenced voltage once at probe
iio: ltc2983: fix device probe
iio: potentiometer: Add driver support for AD5110
dt-bindings: iio: potentiometer: Add AD5110 in trivial-devices
Add ADC driver support for Renesas RZ/G2L A/D converter in SW
trigger mode.
A/D Converter block is a successive approximation analog-to-digital
converter with a 12-bit accuracy and supports a maximum of 8 input
channels.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210804202118.25745-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add voltage notifier, no need to query regulator voltage for
every saradc read, just get regulator voltage once at probe.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210810011007.54066-1-xxm@rock-chips.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add iio map to allow power driver to read out values as a consumer.
This approach does not block later addition of devicetree support
which would be helpful if there is an in-kernel consumer for AIN0/1.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use clk_prepare_enable()/clk_disable_unprepare() in preparation for switch
to Common Clock Framework, otherwise the following is visible:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:1011 clk_core_enable+0x9c/0xbc
Enabling unprepared ep93xx-adc
CPU: 0 PID: 1 Comm: swapper Not tainted 5.13.0-rc5-... #1
Hardware name: Cirrus Logic EDB9302 Evaluation Board
[<c000d5b0>] (unwind_backtrace) from [<c000c590>] (show_stack+0x10/0x18)
[<c000c590>] (show_stack) from [<c03a5f38>] (dump_stack+0x20/0x2c)
[<c03a5f38>] (dump_stack) from [<c03a2098>] (__warn+0x98/0xc0)
[<c03a2098>] (__warn) from [<c03a2150>] (warn_slowpath_fmt+0x90/0xc0)
[<c03a2150>] (warn_slowpath_fmt) from [<c01d8358>] (clk_core_enable+0x9c/0xbc)
[<c01d8358>] (clk_core_enable) from [<c01d8698>] (clk_core_enable_lock+0x18/0x30)
[<c01d8698>] (clk_core_enable_lock) from [<c0266560>] (ep93xx_adc_probe+0xe4/0x1a0)
[<c0266560>] (ep93xx_adc_probe) from [<c02126e0>] (platform_probe+0x34/0x80)
[<c02126e0>] (platform_probe) from [<c0210bf8>] (really_probe+0xe8/0x394)
[<c0210bf8>] (really_probe) from [<c0211464>] (device_driver_attach+0x5c/0x64)
[<c0211464>] (device_driver_attach) from [<c02114e8>] (__driver_attach+0x7c/0xec)
[<c02114e8>] (__driver_attach) from [<c020f1b4>] (bus_for_each_dev+0x78/0xc4)
[<c020f1b4>] (bus_for_each_dev) from [<c0211570>] (driver_attach+0x18/0x24)
[<c0211570>] (driver_attach) from [<c020fab4>] (bus_add_driver+0x140/0x1cc)
[<c020fab4>] (bus_add_driver) from [<c0211c44>] (driver_register+0x74/0x114)
[<c0211c44>] (driver_register) from [<c02134f8>] (__platform_driver_register+0x18/0x24)
[<c02134f8>] (__platform_driver_register) from [<c0470148>] (ep93xx_adc_driver_init+0x10/0x1c)
[<c0470148>] (ep93xx_adc_driver_init) from [<c045ce88>] (do_one_initcall+0x7c/0x1a4)
[<c045ce88>] (do_one_initcall) from [<c045d184>] (kernel_init_freeable+0x17c/0x1fc)
[<c045d184>] (kernel_init_freeable) from [<c03a64d0>] (kernel_init+0x8/0xf8)
[<c03a64d0>] (kernel_init) from [<c00082d8>] (ret_from_fork+0x14/0x3c)
...
ep93xx-adc ep93xx-adc: Cannot enable clock
ep93xx-adc: probe of ep93xx-adc failed with error -108
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20210613233041.128961-2-alexander.sverdlin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For the function of platform_get_irq(), the example in platform.c is
* int irq = platform_get_irq(pdev, 0);
* if (irq < 0)
* return irq;
the return value of zero is unnecessary to check, so make the right
check and simplify code.
Note that platform_get_irq() is documented as never returning 0
so this is a minor optmization rather than a fix.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210802120929.33760-1-tangbin@cmss.chinamobile.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The JZ4760B variant differs slightly from the JZ4760: it has a bit called VBAT_SEL in the CFG register.
In order to correctly sample the battery voltage on existing handhelds using this SOC, the bit must be cleared.
We leave the possibility to set the bit, by using the "ingenic,use-internal-divider" in the devicetree.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Link: https://lore.kernel.org/r/20210726082033.351533-5-cbranchereau@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The jz4760 sadc is very similar to the jz4770 one, but has a VREF of 2.5V
and 3 aux channels.
modify ingenic_adc_read_chan_info_raw() needs a change to account for it.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210726082033.351533-4-cbranchereau@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The jz4760(b) socs have 3 aux channels.
The purpose of has_aux2 is to set the MD bits used to select
the AUX channel to be sampled, not to describe the hardware.
Rename it to a more appropriate name.
Signed-off-by: Christophe Branchereau <cbranchereau@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210726082033.351533-2-cbranchereau@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently the for-loop that scans for the optimial adc_period iterates
through all the possible adc_period levels because the exit logic in
the loop is inverted. I believe the comparison should be swapped and
the continue replaced with a break to exit the loop at the correct
point.
Addresses-Coverity: ("Continue has no effect")
Fixes: e08e19c331 ("iio:adc: add iio driver for Palmas (twl6035/7) gpadc")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730071651.17394-1-colin.king@canonical.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align the function arguments after a line-break with the opening
parenthesis on the previous line. No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210717233718.332267-4-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a missing space between if and the opening parenthesis to make the
coding style consistent across the whole driver. No functional changes
intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210717233718.332267-3-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
G12A and newer don't use the SAR ADC to read the SoC temperature from
within the firmware. Instead there's now a dedicated thermal sensor.
Disable the BL30 integration for G12A and newer SoCs to save a few CPU
cycles when reading samples.
Adding a separate struct meson_sar_adc_data is a good idea anyways
because starting with G12A there's some extra registers to read the
samples in a simplified way.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20210717233718.332267-2-martin.blumenstingl@googlemail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the defined variable "dev" to make the code cleaner.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210720125945.11548-1-tangbin@cmss.chinamobile.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS7950 requires that CS is deasserted after each SPI word. Before
commit e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") the driver used a message with one spi transfer per channel
where each but the last one had .cs_change set to enforce a CS toggle.
This was wrongly translated into a message with a single transfer and
.cs_change set which results in a CS toggle after each word but the
last which corrupts the first adc conversion of all readouts after the
first readout.
Fixes: e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce CPU usage")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: David Lechner <david@lechnology.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210709101110.1814294-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is similar to other devices, but with 8 channels.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210712014507.97477-1-xxm@rock-chips.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The call to pm_runtime_put_noidle() in remove() is not balancing a
counter increment. Note this doesn't matter as the runtime pm core
will not allow the counter to go negative. However, it is confusing
to the reader so let's remove it.
The pm_runtime_resume_and_get() replacement was found using coccicheck
script under review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-3-jic23@kernel.org
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Fixes: f214ff521f ("iio: ti-ads8688: Update buffer allocation for timestamps")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-5-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Add a comment on why the buffer is the size it is as not immediately
obvious.
Found during an audit of all calls of this function.
Fixes: 6dd112b9f8 ("iio: adc: mxs-lradc: Add support for ADC driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-4-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of this function.
Fixes: d3bf60450d ("iio: hx711: add triggered buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-3-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of this function.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210613152301.571002-2-jic23@kernel.org
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO ADC group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513111035.77950-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since all AD Sigma-Delta drivers now use the
devm_ad_sd_setup_buffer_and_trigger() function, we can remove the old
ad_sd_{setup,cleanup}_buffer_and_trigger() functions.
This way we can discourage new drivers that use the ad_sigma_delta
lib-driver to use these (older functions).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-13-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As not many steps were not already devm_ managed, use
devm_add_action_or_reset() to handle the rest.
This also uses the new devm_ad_sd_setup_buffer_and_trigger() function.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-12-aardelean@deviqon.com
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7192 driver to use device-managed
functions.
The regulators and the mclk requires devm_add_action_or_reset() callbacks
though.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-11-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The devm_clk_get_optional() helper returns NULL when devm_clk_get() returns
-ENOENT.
This makes things slightly cleaner. The added benefit is mostly cosmetic.
Also, a minor detail with this call, is that the reference for the parent
device is taken as `spi->dev` instead of `&st->sd.spi->dev` (which looks a
little quirky).
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-10-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7780 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-9-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7791 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-8-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With the devm_ad_sd_setup_buffer_and_trigger() helper, it's a bit easier
now to convert the probe of the AD7793 driver to use device-managed
functions.
Only the regulator disable requires a devm_add_action_or_reset() callback.
This change does that, cleaning up the driver a bit.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-7-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a version of ad_sd_setup_buffer_and_trigger() with all underlying
functions (that are used) being replaced with their device-managed
variants.
One thing to take care here is with {devm_}iio_trigger_alloc(), where both
functions take a parent-device object as the first parameter.
To make sure nothing quirky is happening, the devm_ad_sd_probe_trigger()
function is checking that the provided 'dev' reference is the same as the
one stored on the 'struct ad_sigma_delta' driver data.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513120752.90074-6-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There are a couple of large cleanup sets in here alongside a number of new
drivers.
Note an immutable branch merged to add a stub for i2c_verify_client()
as needed to avoid a build issue in the fxls8962af driver as a result of a
workaround for a device errata that only applies when i2c interface is used.
Counters
========
New device support
* intel,quadrature encoder peripheral found on Elkhart Lake platforms.
- New driver.
IIO
===
New device support
* amstaos,tsl2591 ambient light sensor.
- New driver + bindings
- Follow up fix to ensure some local variables are suitable for error
handling.
* fsl,fxls8962af + fsl,fxls8964af accelerometers
- New driver + bindings
- Includes an errata work around that cause a build bot failure fixed
by adding a stub to i2c.
* kionix,kxcjk-1013
- Add support for KX023-1025 device. Mostly a different register map
that needed to be supported.
* murata,sca3300 accelerometer
- New driver + bindings
* st,lsm9ds0 IMU
- Rework of st,sensors driver to cleanly support this new glue driver
that enables the two parts of the LSM9DS0.
* ti,tsc2046 touchscreen controller ADC.
- New driver. Intent here is to use this with existing IIO consumer
drivers such as resistive-adc-touch.
- Follow up fix to avoid an issue with unsigned subtraction in error
check.
* ti,tmp117 digital temperature sensor
- New driver + bindings
Features
* adi,ad5755
- Add missing dt-binding doc
* adi,ad7298
- Add ACPI ID used on Intel Galileo Gen 1 boards.
- Add missing dt-binding doc
* adi,ad7476
- Add missing dt-binding doc
* adi,ad7746
- Add missing dt-binding doc for this driver that will hopefully move out
of staging shortly. Update staging driver to use the binding instead of
platform data.
* adi,adis16201 + adis16209
- Add missing dt-binding doc
* adi,adis16480
- Support burst mode for adis16495 and adis16497 parts.
* bosch,bma220
- Add missing dt-binding doc
* fsl,mma7455
- Add missing dt-binding doc
* iio-rescale
- Support handling of processed channels from provider. Some ADCs
require (typically non linear) calibration functions to be applied,
and so provide only IIO_CHAN_INFO_PROCESSED read back. They can be
used as providers to the iio-rescale driver which needs to handle them
somewhat differently from IIO_CHAN_INFO_RAW
* sensiron,sps30
- Support the serial interface. Note this required significant
refactoring of existing driver.
* st,st-sensors
- Add mount matrix support for normal dt-binding whilst continuing to
support the odd ACPI approach for accelerometers.
* ti,dac082s085 + similar
- Add missing dt-binding doc
* trivial-devices - add entries for
- memsic,mx4005, memsic,mx6255 and memsic,mxc6655
- sensortek,stk8312 and sensortek,stk8ba50
Cleanup / minor fixes
* core
- Use devm_add_action_or_reset() to replace boilerplate in several
driver and core IIO devm_* functions.
- Fix an error path issue introduced by above, that could return an
error pointer rather than the expected null from dev_iio_device_alloc()
- Move more IIO internals related fields from struct iio_dev to
struct iio_dev_opaque.
- Drop unused final update of in_loc in demux setup.
* Docs
- Move some docs from driver specific to core dos to avoid replication
of names which the documentation builder does not allow.
Note this means adding a few device specific notes to the general docs
to cover the more unusual uses of the ABI.
- ABI: Move old buffer/* and scan_elements/* docs to obsolete as now we
have the bufferX/* variant. Not we are not getting rid of these
interfaces, just encouraging new code to use the new interface.
* IIO wide:
- Tidy up new cases of dev.parent etc being set in drivers as the core
now does it.
- Fix more cases of possible miss-aligned buffers when passed to
iio_push_to_buffers_with_timestamp(). Note we only have one known
instance of anyone seeing this bug actually happening, so this has been
a low priority cleanup effort for several cycles.
- sysfs_emit() used in more drivers.
- Runtime pm tidy up and use of pm_runtime_resume_and_get()
- Buffer alignment fixes as iio_push_to_buffers_with_timestamp requires
that the timestamp when inserted by naturally aligned + consumers can
assume that all fields are naturally aligned. Part of a long running
effort, with at least 2 more series to come tackling additional
variants.
- Stop specifying "mount-matrix" property name in every lookup of the
mount matrix from firmware by hard coding it in the core.
* adi,ad7476
- Handle the variety of different regulators used by the parts supported
by this driver (came up in dt-binding review)
* adi,ad7746
- Trivial drop of if (ret) return ret; return 0; pattern
- Tidy up comments
- Pull capdac setup out to own function.
* adi,ad7766
- Trivial drop of if (ret) return ret; return 0; pattern
* adi,adis
- Avoid returning error codes in interrupt handlers.
- Handle a failure in spi_write in the trigger handler.
- Rework to add updating of device page after changing it.
- Don't push data to IIO buffers when read failed.
- Add configuration of burst max speed to core avoid handling this in
each driver.
- Use the adis_dev_lock() helper in adis16260 and adis16136 drivers.
- Excessive includes cleanup via include-what-you-use static checker
after zero day highlighted that these needed updating.
* afe
- Amend binding to add #io-channel-cells, thus allowing this IIO
consumer to also be an IIO provider.
* aosong,am2315
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* bosch,bma180
- Adding missing bandwidth settings (500, 1000 Hz)
* bosch,bme680
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* ep93xx_adc,
- Drop a redundant error print.
* maxim,max118
- Convert remainder of probe() to devm_ managed functions.
- Avoid some repeated jumping back and forth between iio_dev and
spi structures.
* maxim,max11100
- Use get_unaligned_be16() instead of open coding.
- Convert remainder of probe() to devm_ managed functions.
* samsung,exynos_adc
- Unused error value dropped.
* sensiron,sgp30
- Drop use of %hx in favor of %x and letting the normal type conversion
work.
* sensortek,stk8312
- Add lowercase device id and note uppercase version deprecated.
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* sprx,sc72xx_adc
- add MODULE_DEVICE_TABLE
* st,lsm6dsx
- Fix docs of valid ODRs
* st,sensors
- dt-binding rework. Two efforts on this crossed in a previous cycle
so this update cherry picks the best of the two yaml conversions.
- Don't copy the channel spec array as now ext_info is no longer modified.
* st,stm32-adc
- tidy up some docs that were marked as kernel-doc but aren't.
* ti,adc081c, ti,adc0832, ti,adc108s102 and ti,adc161s626
- Convert remainder of probe() functions to devm_ managed functions
to simplify error handing and remove paths.
-----BEGIN PGP SIGNATURE-----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=Zved
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of new IIO/counter device support, features and cleanup for 5.14
There are a couple of large cleanup sets in here alongside a number of new
drivers.
Note an immutable branch merged to add a stub for i2c_verify_client()
as needed to avoid a build issue in the fxls8962af driver as a result of a
workaround for a device errata that only applies when i2c interface is used.
Counters
========
New device support
* intel,quadrature encoder peripheral found on Elkhart Lake platforms.
- New driver.
IIO
===
New device support
* amstaos,tsl2591 ambient light sensor.
- New driver + bindings
- Follow up fix to ensure some local variables are suitable for error
handling.
* fsl,fxls8962af + fsl,fxls8964af accelerometers
- New driver + bindings
- Includes an errata work around that cause a build bot failure fixed
by adding a stub to i2c.
* kionix,kxcjk-1013
- Add support for KX023-1025 device. Mostly a different register map
that needed to be supported.
* murata,sca3300 accelerometer
- New driver + bindings
* st,lsm9ds0 IMU
- Rework of st,sensors driver to cleanly support this new glue driver
that enables the two parts of the LSM9DS0.
* ti,tsc2046 touchscreen controller ADC.
- New driver. Intent here is to use this with existing IIO consumer
drivers such as resistive-adc-touch.
- Follow up fix to avoid an issue with unsigned subtraction in error
check.
* ti,tmp117 digital temperature sensor
- New driver + bindings
Features
* adi,ad5755
- Add missing dt-binding doc
* adi,ad7298
- Add ACPI ID used on Intel Galileo Gen 1 boards.
- Add missing dt-binding doc
* adi,ad7476
- Add missing dt-binding doc
* adi,ad7746
- Add missing dt-binding doc for this driver that will hopefully move out
of staging shortly. Update staging driver to use the binding instead of
platform data.
* adi,adis16201 + adis16209
- Add missing dt-binding doc
* adi,adis16480
- Support burst mode for adis16495 and adis16497 parts.
* bosch,bma220
- Add missing dt-binding doc
* fsl,mma7455
- Add missing dt-binding doc
* iio-rescale
- Support handling of processed channels from provider. Some ADCs
require (typically non linear) calibration functions to be applied,
and so provide only IIO_CHAN_INFO_PROCESSED read back. They can be
used as providers to the iio-rescale driver which needs to handle them
somewhat differently from IIO_CHAN_INFO_RAW
* sensiron,sps30
- Support the serial interface. Note this required significant
refactoring of existing driver.
* st,st-sensors
- Add mount matrix support for normal dt-binding whilst continuing to
support the odd ACPI approach for accelerometers.
* ti,dac082s085 + similar
- Add missing dt-binding doc
* trivial-devices - add entries for
- memsic,mx4005, memsic,mx6255 and memsic,mxc6655
- sensortek,stk8312 and sensortek,stk8ba50
Cleanup / minor fixes
* core
- Use devm_add_action_or_reset() to replace boilerplate in several
driver and core IIO devm_* functions.
- Fix an error path issue introduced by above, that could return an
error pointer rather than the expected null from dev_iio_device_alloc()
- Move more IIO internals related fields from struct iio_dev to
struct iio_dev_opaque.
- Drop unused final update of in_loc in demux setup.
* Docs
- Move some docs from driver specific to core dos to avoid replication
of names which the documentation builder does not allow.
Note this means adding a few device specific notes to the general docs
to cover the more unusual uses of the ABI.
- ABI: Move old buffer/* and scan_elements/* docs to obsolete as now we
have the bufferX/* variant. Not we are not getting rid of these
interfaces, just encouraging new code to use the new interface.
* IIO wide:
- Tidy up new cases of dev.parent etc being set in drivers as the core
now does it.
- Fix more cases of possible miss-aligned buffers when passed to
iio_push_to_buffers_with_timestamp(). Note we only have one known
instance of anyone seeing this bug actually happening, so this has been
a low priority cleanup effort for several cycles.
- sysfs_emit() used in more drivers.
- Runtime pm tidy up and use of pm_runtime_resume_and_get()
- Buffer alignment fixes as iio_push_to_buffers_with_timestamp requires
that the timestamp when inserted by naturally aligned + consumers can
assume that all fields are naturally aligned. Part of a long running
effort, with at least 2 more series to come tackling additional
variants.
- Stop specifying "mount-matrix" property name in every lookup of the
mount matrix from firmware by hard coding it in the core.
* adi,ad7476
- Handle the variety of different regulators used by the parts supported
by this driver (came up in dt-binding review)
* adi,ad7746
- Trivial drop of if (ret) return ret; return 0; pattern
- Tidy up comments
- Pull capdac setup out to own function.
* adi,ad7766
- Trivial drop of if (ret) return ret; return 0; pattern
* adi,adis
- Avoid returning error codes in interrupt handlers.
- Handle a failure in spi_write in the trigger handler.
- Rework to add updating of device page after changing it.
- Don't push data to IIO buffers when read failed.
- Add configuration of burst max speed to core avoid handling this in
each driver.
- Use the adis_dev_lock() helper in adis16260 and adis16136 drivers.
- Excessive includes cleanup via include-what-you-use static checker
after zero day highlighted that these needed updating.
* afe
- Amend binding to add #io-channel-cells, thus allowing this IIO
consumer to also be an IIO provider.
* aosong,am2315
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* bosch,bma180
- Adding missing bandwidth settings (500, 1000 Hz)
* bosch,bme680
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* ep93xx_adc,
- Drop a redundant error print.
* maxim,max118
- Convert remainder of probe() to devm_ managed functions.
- Avoid some repeated jumping back and forth between iio_dev and
spi structures.
* maxim,max11100
- Use get_unaligned_be16() instead of open coding.
- Convert remainder of probe() to devm_ managed functions.
* samsung,exynos_adc
- Unused error value dropped.
* sensiron,sgp30
- Drop use of %hx in favor of %x and letting the normal type conversion
work.
* sensortek,stk8312
- Add lowercase device id and note uppercase version deprecated.
- Drop ACPI id. Unlikely this one is in the wild and it isn't valid
ACPI naming.
* sprx,sc72xx_adc
- add MODULE_DEVICE_TABLE
* st,lsm6dsx
- Fix docs of valid ODRs
* st,sensors
- dt-binding rework. Two efforts on this crossed in a previous cycle
so this update cherry picks the best of the two yaml conversions.
- Don't copy the channel spec array as now ext_info is no longer modified.
* st,stm32-adc
- tidy up some docs that were marked as kernel-doc but aren't.
* ti,adc081c, ti,adc0832, ti,adc108s102 and ti,adc161s626
- Convert remainder of probe() functions to devm_ managed functions
to simplify error handing and remove paths.
* tag 'iio-for-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (171 commits)
i2c: core: Add stub for i2c_verify_client() if !CONFIG_I2C
iio: adis: Cleanout unused headers
iio: accel: bma180: Add missing 500 Hz / 1000 Hz bandwidth
counter: Add support for Intel Quadrature Encoder Peripheral
staging: iio: cdc: ad7746: extract capac setup to own function
staging: iio: cdc: ad7746: clean up probe return
staging: iio: cdc: ad7746: remove ordinary comments
iio: adc: ti-adc161s626: Use devm managed functions for all of probe.
iio: adc: ti-adc108s102: Use devm managed functions for all of probe()
iio: adc: ti-adc0832: Use devm managed functions for all of probe()
iio: adc: ti-adc081c: Use devm managed functions for all of probe()
iio: adc: max1118: Avoid jumping back and forth between spi and iio structures
iio: adc: max1118: Use devm_ managed functions for all of probe
iio: adc: max11100: Use devm_ functions for rest of probe()
iio: adc: max11100: Use get_unaligned_be16() rather than opencoding.
iio: chemical: sgp30: Drop use of %hx in format string.
iio: gyro: st_gyro: Support mount matrix
iio: magnetometer: st_magn: Support mount matrix
iio: accel: st_sensors: Stop copying channels
iio: accel: st_sensors: Support generic mounting matrix
...
Simplifies error handling and allows us to drop remove entirely.
The regulator handling in this driver was unusual as it would try to
acquire the regulator, but if that failed with an error would continue.
We should get a stub regulator if one isn't provided in DT and an error
could indicate an actual problem preventing the device being powered
(perhaps a need to defer). So this handling is cleaned up (arguably
that might be a fix but given no one has run into it, I haven't broken
it out separately.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-9-jic23@kernel.org
Simplifies error handling and lets us drop remove() entirely.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Bogdan Pricop <bogdan.pricop@emutex.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-8-jic23@kernel.org
Simplifies error handling, plus allows us to drop the remove()
function entirely.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-7-jic23@kernel.org
Changing from passing the spi structure into various functions to
passing struct iio_dev avoids use of spi_get_drvdata and lets us
stop setting that at all. Previous code was unnecessarily complex.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-5-jic23@kernel.org
This simplifies error handling and allows us to drop the remove
function entirely.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-4-jic23@kernel.org
By using devm_add_action_or_reset() to manage the regulator disable,
it becomes simple to use managed functions for all of remove.
This simplifies error handling and allows us to drop the remove()
function entirely.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-3-jic23@kernel.org
The function is more explicit in showing the intent + quicker on some
platforms.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210516172520.1398835-2-jic23@kernel.org
These variables are unsigned so the condition can't be less than zero
and the warning message will never be printed.
Fixes: 9374e8f5a3 ("iio: adc: add ADC driver for the TI TSC2046 controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YJ+ZuO43TnguY5vq@mwanda
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set error code while device ID query failed.
Fixes: 88bc30548a ("IIO: ADC: New driver for AD7792/AD7793 3 Channel SPI ADC")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes tag is where the max channels became 8, but timestamp space was missing
before that.
Fixes: 851644a60d ("iio: adc: ad7923: Add support for the ad7908/ad7918/ad7928")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Junho <djunho@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210501165314.511954-3-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Add space for the timestamp to be inserted. Also ensure correct
alignment for passing to iio_push_to_buffers_with_timestamp()
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210501165314.511954-2-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
In the function ad7766_probe(), the return value of
devm_iio_device_register() can be zero or ret, Thus it
is unnecessary to repeated check here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210511134739.948-1-tangbin@cmss.chinamobile.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of uses of
iio_push_to_buffers_with_timestamp()
Fixes: 0010d6b444 ("iio: adc: vf610: Add IIO buffer support for Vybrid ADC")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210501170121.512209-10-jic23@kernel.org
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of this function.
Fixes: ecc24e72f4 ("iio: adc: Add TI ADS1015 ADC driver support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210501170121.512209-9-jic23@kernel.org
1 instance found using coccicheck script under review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
The other instance changed did not check for failure of the
pm_runtime_get_sync() so that is added.
Note the remaining pm_runtime_get_sync() call is left alone because it
is not obvious what to do on failure to power up in remove()
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-29-jic23@kernel.org
MODULE_DEVICE_TABLE is used to extract the device information out of the
driver and builds a table when being compiled. If using this macro,
kernel can find the driver if available when the device is plugged in,
and then loads that driver and initializes the device.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Continuing from Alexandru Ardelean's introduction of the split between
driver modifiable fields and those that should only be set by the core.
This could have been done in two steps to make the actual move after
introducing iio_device_id() but there seemed limited point to that
given how mechanical the majority of the patch is.
Includes fixup from Alex for missing mxs-lradc-adc conversion.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426174911.397061-2-jic23@kernel.org
Already set to same value in devm_iio_device_alloc()
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Tomislav Denis <tomislav.denis@avl.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426170251.351957-6-jic23@kernel.org
Already set to the same value in devm_iio_device_alloc()
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426170251.351957-5-jic23@kernel.org
This is already set to the same value in devm_iio_device_alloc()
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426170251.351957-4-jic23@kernel.org
Basically the TI TSC2046 touchscreen controller is 8 channel ADC optimized for
the touchscreen use case. By implementing it as an IIO ADC device, we can
make use of resistive-adc-touch and iio-hwmon drivers.
Polled readings are currently not implemented to keep this patch small, so
iio-hwmon will not work out of the box for now.
So far, this driver was tested with a custom version of resistive-adc-touch driver,
since it needs to be extended to make use of Z1 and Z2 channels. The X/Y
are working without additional changes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210428073208.19570-4-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
W=1 highlights these two cases that are obviously not in kernel-doc
format.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Not all of the parts supported by this driver use single supply.
Hence we add chip_info fields to say what additional supplies exist
and in the case of vref, ensure that is used for the reference voltage
rather than vcc.
One corner case is the ad7091r which has an internal reference that
can be over-driven by an external reference connected on the vref pin.
To handle that force_ext_vref is introduced and set if an optional
vref regulator is present.
Tested using really simple QEMU model and some fixed regulators.
The devm_add_action_or_reset() callback is changed to take the
regulator as it's parameter so we can use one callback for all the
different regulators without having to store pointers to them in
the iio_priv() structure.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210425163154.73209-2-jic23@kernel.org
Use devm_add_action_or_reset() instead of devres_alloc() and
devres_add(), which works the same. This will simplify the
code. There is no functional changes.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1617881896-3164-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The initialization of 'ret' variable in probe function is shortly after
overwritten. This initialization is simply not used.
Addresses-Coverity: Unused value
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20210410164728.8096-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change fixes a corner-case, where for a zero regulator value, the
driver would exit early, initializing the driver only partially.
The driver would be in an unknown state.
This change reworks the code to check regulator_voltage() return value
for negative (error) first, and return early. This is the more common
idiom.
Also, this change is removing the 'voltage_uv' variable and using the 'ret'
value directly. The only place where 'voltage_uv' is being used is to
compute the internal reference voltage, and the type of this variable is
'int' (same are for 'ret'). Using only 'ret' avoids having to assign it on
the error path.
Fixes: ab0afa65bb ("staging: iio: adc: ad7192: fail probe on get_voltage")
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: <Stable@vger.kernel.org>
Found by inspection.
If the internal clock source is being used, the driver doesn't
call clk_prepare_enable() and as such we should not call
clk_disable_unprepare()
Use the same condition to protect the disable path as is used
on the enable one. Note this will all get simplified when
the driver moves over to a full devm_ flow, but that would make
backporting the fix harder.
Fix obviously predates move out of staging, but backporting will
become more complex (and is unlikely to happen), hence that patch
is given in the fixes tag.
Alexandru's sign off is here because he added this patch into
a larger series that Jonathan then applied.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Cc: <Stable@vger.kernel.org>
Channel numbering must start at 0 and then not have any holes, or
it is possible to overflow the available storage. Note this bug was
introduced as part of a fix to ensure we didn't rely on the ordering
of child nodes. So we need to support arbitrary ordering but they all
need to be there somewhere.
Note I hit this when using qemu to test the rest of this series.
Arguably this isn't the best fix, but it is probably the most minimal
option for backporting etc.
Alexandru's sign-off is here because he carried this patch in a larger
set that Jonathan then applied.
Fixes: d7857e4ee1 ("iio: adc: ad7124: Fix DT channel configuration")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Cc: <Stable@vger.kernel.org>
If the devm_regulator_get() call succeeded but not the regulator_enable()
then regulator_disable() would be called on a regulator that was not
enabled.
Fix this by moving regulator enabling / disabling over to
devm_ management via devm_add_action_or_reset.
Alexandru's sign-off here because he pulled Jonathan's patch into
a larger set which Jonathan then applied.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Cc: <Stable@vger.kernel.org>
The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
The conversion to new style transfer delay will cause an issue with a
newly added staging driver which has a straightforward resolution in
-next.
- Completion of the conversion to new style transfer delay
configuration.
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree.
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon Kunpeng,
MediaTek MT8195,
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmCG0FYACgkQJNaLcl1U
h9BXlAf/ZQaU8Nq4NY2jgjzjUoplF4qSFvCZ05CXqfYftaAOp06AmoOwNuNTz2gU
Fkxouuw3D0hNmaeVusF1PaRjIvJCu+RO68EDrzTJlcFytyC8CxWSDE4Yw6ytOBUM
OWZdVXsuw0CUk3VRJl2ycCooeTyKaCksfkVucocZAoyexcfQrFpxkOCUbA8hVM43
Hghzb8HWAZUerrfwreSwfvyVMralR3rqqbZFKgSgT/sRM3zpaR4sctIkNgKKEbFE
eRPRfBIWWZdJtjQ+uifFAc3jJHeZlmNXuQq3C+ETd2vQDFlymTxj+U3u74ieZxrm
c6V4u4R3+Qx9qONV/q0LV6E4sBSvdw==
=cBUy
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
Summary:
- Completion of the conversion to new style transfer delay
configuration
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon
Kunpeng, MediaTek MT8195"
* tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (113 commits)
spi: Rename enable1 to activate in spi_set_cs()
spi: Convert Freescale QSPI binding to json schema
spi: stm32-qspi: fix debug format string
spi: tools: make a symbolic link to the header file spi.h
spi: fsi: add a missing of_node_put
spi: Make error handling of gpiod_count() call cleaner
spidev: Add Micron SPI NOR Authenta device compatible
spi: brcm,spi-bcm-qspi: convert to the json-schema
spi: altera: Add DFL bus driver for Altera API Controller
spi: altera: separate core code from platform code
spi: stm32-qspi: Fix compilation warning in ARM64
spi: Handle SPI device setup callback failure.
spi: sync up initial chipselect state
spi: stm32-qspi: Add dirmap support
spi: stm32-qspi: Trigger DMA only if more than 4 bytes to transfer
spi: stm32-qspi: fix pm_runtime usage_count counter
spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails
spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op
spi: spi-zynqmp-gqspi: Resolved slab-out-of-bounds bug
spi: spi-zynqmp-gqspi: fix hang issue when suspend/resume
...
Because a dependency on HAS_IOMEM and OF was added for the ADI AXI ADC
driver, this makes the AD9467 driver have some build/dependency issues
when OF is disabled (typically on ACPI archs like x86).
This is because the selection of the AD9467 enforces the ADI_AXI_ADC symbol
which is blocked by the OF (and potentially HAS_IOMEM) being disabled.
To fix this, we make the AD9467 driver depend on the ADI_AXI_ADC symbol.
The AD9467 driver cannot operate on it's own. It requires the ADI AXI ADC
driver to stream data (or some similar IIO interface).
So, the fix here is to make the AD9467 symbol depend on the ADI_AXI_ADC
symbol. At some point this could become it's own subgroup of high-speed
ADCs.
Fixes: be24c65e9f ("iio: adc: adi-axi-adc: add proper Kconfig dependencies")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210324182746.9337-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver was in an odd half way state between devm based cleanup
and manual cleanup (most of which was missing).
I would guess something went wrong with a rebase or similar.
Anyhow, this basically finishes the job as a precursor to improving
the regulator handling.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 4bb2b8f94a ("iio: adc: ad7476: implement devm_add_action_or_reset")
Cc: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210401171759.318140-2-jic23@kernel.org
These devices are not able to mask the signal used as a data ready
interrupt. As such they previously requested the irq then immediately
disabled it. Now we can avoid the potential of a spurious interrupt
by avoiding the irq being auto enabled in the first place.
I'm not sure how this code could have been called with the irq already
disabled, so I believe the conditional would always have been true and
have removed it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-8-jic23@kernel.org
This new flag ensures a requested irq is not autoenabled, thus removing
the need for the disable_irq() that follows and closing off any chance
of spurious interrupts.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-5-jic23@kernel.org
Whilst a race during interrupt enabling is probably not a problem,
it is better to not enable the interrupt at all. The new
IRQF_NO_AUTOEN flag allows us to do that.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-4-jic23@kernel.org
Disabling an irq before the driver has actually atempted to request it
may work, but is definitely not as clean as just requesting it as
normal but with the auto enable disabled.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-3-jic23@kernel.org
As iio_poll_trigger() is safe against spurious interrupts when the
trigger is not enabled, this is not a fix despite looking like
a race. It is nice to simplify the code however so the interrupt
is never enabled in the first place.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20210402184544.488862-2-jic23@kernel.org
Dropped __func__ while using dev_dbg() and pr_debug()
If the function name is desired, it can be configured using
dynamic debug.
Signed-off-by: Mugilraj Dhavachelvan <dmugil2000@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210401154343.41527-1-dmugil2000@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The timestamp control has been a function implemented in the core of
IIO for a long time, so this comment is incorrect and has clearly been
cut and paste into all these drivers.
The remainder of the comment added nothing and was confusing so dropped
that as well.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210401145410.226917-1-jic23@kernel.org
Registers the device using the devm variant.
This is the final step of converting the ad7923 to only use devm routines,
meaning that the ad7923_remove() function is no longer needed to release
resources on device detach.
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/b0146465d52f4e259f5f95c83c71e72f065093da.1616966903.git.lucas.p.stankus@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Converts the iio_triggered_buffer_setup() call to its device-managed
counterpart.
With this, the error handling routine in the ad7923_probe() function
becomes unnecessary as well as the iio_triggered_buffer_cleanup() call.
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/fe46a45caaa788f333d78367968272de728f4a6e.1616966903.git.lucas.p.stankus@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adds a device-managed action to handle disabling the driver's regulator on
device detach.
This slightly simplifies deinitialization and enables further conversion of
the driver to device-managed routines without breaking the init order.
Signed-off-by: Lucas Stankus <lucas.p.stankus@gmail.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/49a7c0436ca1186313dbccf3d810d0cf38cb5b37.1616966903.git.lucas.p.stankus@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
-----BEGIN PGP SIGNATURE-----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=jeRJ
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
1st set of IIO/counter device support, features and cleanup in the 5.13 cycle
Big set in here from Alexandru Ardelean enabling multiple buffer support.
This includes providing a new directory per buffer that combines
what was previously in buffer/ and scan_elements/. Old interfaces still
in place for compatiblity.
Note immuatable branch for scmi patches to allow for some significant
rework going on in that subsystem. Merge required updating to reflect
some changes in IIO.
Late rebase to fix some wrong fixes tags due to some earlier rebases
made necessary by messing up the immutable branch.
IIO New Device Support
* adi,ad5686
- Add info to support AD5673R and AD5677R
* bosch,bmi088
- New driver supporting this accelerometer + gyroscope
* cros_ec_mkbp
- New driver for this proximity sensor that exposes a 'front'
sensor. Very simple switch like device, but driver allows it
to share interface with more sophisticated proximity sensors.
* iio_scmi
- New driver to support ARM SCMI protocol to expose underlying
accelerometers and gyroscopes via this firmware interface.
* st,st_magn
- Add ID for IISMDC magnetometer.
* ti,ads131e0
- New driver supporting ads131e04, ads131e06 and ads131e08 24 bit ADCs
Counter New Device Support
* IRQ or GPIO based counter
- New driver for a conceptually simple counter that uses interrupts
to perform the count.
Features
* core
- Dual buffer supprt including:
Various helpers to centralize handling of bufferer related elements.
Document existing and new IOCTLs
Register the IIO chrdev only if it can actually be used for anything.
Rework attribute group creation in the core (lots of patches)
Merge buffer/ and scan_elements/ entries into one list + maintain
backwards compatible set.
Introduce the internal logic and IOCTL to allow multiple buffers
+ access to an anon FD per buffer to actually read from it.
Tidy up tools/iio/iio_generic_buffer and switch to new interfaces.
Update ABI docs.
A few follow up fixes, unsuprising as this was a huge bit of rework.
- Move common case setting of trig->parent to the core.
- Provide an iio_read_channel_processed_scale() to avoid loss of
precision from iio_read_channel_processed() then applying integer
scale. Use it in ntc_thermistor driver in hwmon.
- Allow drivers to specify labels from elsewhere than DT. Use it for
bmc150 and kxcjk-1013 labels related to position on 2 in one tablets.
- Document label usage for proximity and accelerometer sensors.
- Some local variable renames for consistency
tools
- Add -a parameter to iio_event_monitor to allow autoenabling of events.
* acpi_als
- Add trigger support for devices that don't support notification method.
* adi,ad7124
- Allow more than 8 channels. This is a complex little device, but is
capable of supporting up to 16 channels if the share certain
configuration settings.
* hrtimer-trigger
- Support sampling frequency below 1Hz.
* mediatek,mt8195-auxadc
- Add compatible to binding docs (always also includes mt8173)
* st,stm32-adc
- Enable timetamps when not using DMA.
* vishay,vcnl3020
- Sampling frequency control.
Cleanup and minor fixes:
* treewide
- Use some getter and setter functions instead of opencoding.
- Set of fixes for pointless casts in various drivers.
- Avoid wrong kernel-doc marking on comment blocks.
- Fix various other minor kernel-doc issues shown by W=1
* core
- Use a signed temporary for IIO_VAL_FRACTIONAL_LOG2 to avoid odd casts.
- Fix IIO_VAL_FRACTIONAL_LOG2 for values between -1.0 and 0.0
- Add unit tests for iio_format_value()
* docs
- Fix formatting/typos in iio_configfs.rst and buffers.rst
- Add documentation of index in buffers.rst
- Fix scan element description
- Avoid some issues with HTML generation from ABI docs by moving
duplicated defintions to more generic files.
- Drop reference to long dead mailing list.
* 104-quad
- Remove left over deprecated IIO counter ABI.
* adi,adi-axi-adc
- Fix wrong bit of docs.
* adi,ad5791
- Typos
* adi,ad9834
- Switch to device managed functions in probe.
* adi,adis*
- Add and use helpers for locking to reduced duplication.
* adi,adis16480
- Fix calculation of sampling frequency when using pulse per second input.
* adi,adis16475
- Calculate the IMU scaled internal sampling rate and runtime depending
on sysfs based configuration rather than getting from DT. Drop now
unnecessary property from DT bindings doc.
* cros_ec
- Fix result of a series of recent changes that means extended buffer
attributes turn up in the wrong place. Too complex to revert the
various patches unfortunately so this is a bit messy.
* fsl,mma3452
- Indentation cleanup.
* hid-sensors
- Size of storage needs to increase for some parts when using quaternions.
- Move the get sensistivity attribute to hid-sensors-common to reduce
duplication. Enable it for more device types.
- Correctly handle relative sensitivity if reported that way including
documenting the new ABI.
* maxim,max517
- Use device managed functions in probe.
* mediatek,mt6360-adc
- Use asm/unaligned.h instead of directly including
unaligned/be_byteshift.h
* novuton,npcm-adc
- Local lock instead of missusing mlock.
* semtech,sx9500
- Typos
* st,sensor
- typo fix
* st,spear-adc
- Local lock instead of missusing mlock.
* st,stm32-adc
- Long standing HAS_IOMEM dependency fix.
* st,stm32-counter
- Remove left over deprecated IIO counter ABI.
* ti,palmas-adc
- Local lock instead of missusing mlock.
* ti,tmp007
- Switch to device managed functions in probe.
Other
* MAINTAINERS
- Move Peter Meerwald-Stadler to Credits at his request
* tag 'iio-for-5.13a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (119 commits)
iio: acpi_als: Add trigger support
iio: acpi_als: Add local variable dev in probe
iio: acpi_als: Add timestamp channel
iio: adc: ad7292: Modify the bool initialization assignment
iio: cros: unify hw fifo attributes without API changes
iio: kfifo: add devm_iio_triggered_buffer_setup_ext variant
iio: event_monitor: Enable events before monitoring
dt-bindings: iio: adc: Add compatible for Mediatek MT8195
iio:magnetometer: Add Support for ST IIS2MDC
dt-bindings: iio: st,st-sensors add IIS2MDC.
staging: iio: ad9832: kernel-doc fixes
iio:dac:max517.c: Use devm_iio_device_register()
iio:cros_ec_sensors: Fix a wrong function name in kernel doc.
iio: buffer: kfifo_buf: kernel-doc, typo in function name.
iio: accel: sca3000: kernel-doc fixes. Missing - and wrong function names.
iio: adc: adi-axi-adc: Drop false marking for kernel-doc
iio: adc: cpcap-adc: kernel-doc fix - that should be _ in structure name
iio: dac: ad5504: fix wrong part number in kernel-doc structure name.
iio: dac: ad5770r: kernel-doc fix case of letter R wrong in structure name
iio: adc: ti-adc084s021: kernel-doc fixes, missing function names
...
A bool initializer is best assigned to false rather than 0.
Signed-off-by: Guoqing Chi <chiguoqing@yulong.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20210319062706.5135-1-chi962464zy@163.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This comment block isn't in kernel-doc format so drop the /** marking.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210314164655.408461-7-jic23@kernel.org
The documentation in this driver was nearly kernel-doc and was marked
as such. Unfortunately the format was wrong and function names were
missing. This patch puts them in with minor edits to keep the resulting
line short.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Mårten Lindahl <martenli@axis.com>
Link: https://lore.kernel.org/r/20210314164655.408461-3-jic23@kernel.org
iio_trigger_set_drvdata() sets the trigger device parent to first
argument of viio_trigger_alloc(), no need to do it again in the driver
code.
In xadc_alloc_trigger, given dev is indio_dev->dev.parent, and we call
devm_iio_trigger_alloc wit dev as argument, we do not have to set
data->trig->dev.parent to indio_dev->dev.parent anymore.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-9-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use cocci semantic patch:
@@
expression trigger, P;
@@
trigger = devm_iio_trigger_alloc(P, ...);
...
- trigger->dev.parent = P;
To remove trigger->dev.parent, since it is set by default.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-3-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When allocated with [devm_]iio_trigger_alloc(), set trig device parent to
the device the trigger is allocated for by default.
It can always be reassigned in the probe routine.
Change iio_trigger_alloc() API to add the device pointer to be coherent
with devm_iio_trigger_alloc, using similar interface to
iio_device_alloc().
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210309193620.2176163-2-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently AD7124-8 driver cannot use more than 8 IIO channels
because it was assigning the channel configurations bijectively
to channels specified in the device-tree. This is not possible
to do when using more than 8 channels as AD7124-8 has only 8
configuration registers.
To allow the user to use all channels at once the driver
will keep in memory configurations for all channels but
will program only 8 of them at a time on the device.
If multiple channels have the same configuration, only
one configuration register will be used. If there
are more configurations than available registers only
the last 8 used configurations will be allowed to exist
on the device in a LRU fashion.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210311091154.47785-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
adi,ad7949
* Fix a wrong bitmask that could lead to an undefined bit being included.
adi,adi-axi-adc
* Add missing Kconfig dependencies
adi,adis16400
* Wrong error code handling in adis16400 that could lead to failed probe.
hid-sensor-humidity, temperature
* Fix alignment and space for timestamp channel.
hid-sensor-prox
* Fix an issue with handling of exponent on the channel scaling.
invensense,mpu3050
* Fix a hole in error handling.
qcom,spi-vadc
* Correct scaling
st,ab8500-adc
* Fix wrong scaling (by factor of 1000)
st,stm32-adc
* Add missing HAS_IOMEM dependency
st,stm32-timer-cnt
* Report count when running off internal clock
* Fix issue with not checking ceiling before trying to write to hardware
* Ensure driver doesn't have stashed state which doesn't match hardware by
rereading from hardware in a slow path.
-----BEGIN PGP SIGNATURE-----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=L5Yl
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.12a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO and counter fixes for the 5.12 cycle
adi,ad7949
* Fix a wrong bitmask that could lead to an undefined bit being included.
adi,adi-axi-adc
* Add missing Kconfig dependencies
adi,adis16400
* Wrong error code handling in adis16400 that could lead to failed probe.
hid-sensor-humidity, temperature
* Fix alignment and space for timestamp channel.
hid-sensor-prox
* Fix an issue with handling of exponent on the channel scaling.
invensense,mpu3050
* Fix a hole in error handling.
qcom,spi-vadc
* Correct scaling
st,ab8500-adc
* Fix wrong scaling (by factor of 1000)
st,stm32-adc
* Add missing HAS_IOMEM dependency
st,stm32-timer-cnt
* Report count when running off internal clock
* Fix issue with not checking ceiling before trying to write to hardware
* Ensure driver doesn't have stashed state which doesn't match hardware by
rereading from hardware in a slow path.
* tag 'iio-fixes-for-5.12a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: gyro: mpu3050: Fix error handling in mpu3050_trigger_handler
iio: hid-sensor-temperature: Fix issues of timestamp channel
iio: hid-sensor-humidity: Fix alignment issue of timestamp channel
counter: stm32-timer-cnt: fix ceiling miss-alignment with reload register
counter: stm32-timer-cnt: fix ceiling write max value
counter: stm32-timer-cnt: Report count function when SLAVE_MODE_DISABLED
iio: adc: ab8500-gpadc: Fix off by 10 to 3
iio:adc:stm32-adc: Add HAS_IOMEM dependency
iio: adis16400: Fix an error code in adis16400_initial_setup()
iio: adc: adi-axi-adc: add proper Kconfig dependencies
iio: adc: ad7949: fix wrong ADC result due to incorrect bit mask
iio: hid-sensor-prox: Fix scale not correct issue
iio:adc:qcom-spmi-vadc: add default scale to LR_MUX2_BAT_ID channel
To get access to the big endian byte order parsing helpers
drivers need to include <asm/unaligned.h> and nothing else.
Cc: Gene Chen <gene_chen@richtek.com>
Suggested-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210215153447.48457-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change does a conversion of the devm_iio_dmaengine_buffer_alloc() to
devm_iio_dmaengine_buffer_setup(). This will allocate an IIO DMA buffer and
attach it to the IIO device, similar to devm_iio_triggered_buffer_setup()
(though the underlying code is different, the final logic is the same).
Since the only user of the devm_iio_dmaengine_buffer_alloc() was the
adi-axi-adc driver, this change does the replacement in a single go in the
driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210215104043.91251-7-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All drivers that already call devm_iio_kfifo_allocate() &
iio_device_attach_buffer() are simple to convert to
iio_device_attach_kfifo_buffer() in a single go.
This change does that; the unwind order is preserved.
What is important, is that the devm_iio_kfifo_buffer_setup() be called
after the indio_dev->modes is assigned, to make sure that
INDIO_BUFFER_SOFTWARE flag is set and not overridden by the assignment to
indio_dev->modes.
Also, the INDIO_BUFFER_SOFTWARE has been removed from the assignments of
'indio_dev->modes' because it is set by devm_iio_kfifo_buffer_setup().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>x
Link: https://lore.kernel.org/r/20210215104043.91251-4-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS131E0x are a family of multichannel, simultaneous sampling,
24-bit, delta-sigma, analog-to-digital converters (ADCs) with a
built-in programmable gain amplifier (PGA), internal reference
and an onboard oscillator.
Datasheet: https://www.ti.com/lit/ds/symlink/ads131e08.pdf
Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Link: https://lore.kernel.org/r/20210202084107.3260-2-tomislav.denis@avl.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For non-DMA usage, we have an easy way to associate a timestamp with a
sample: iio_pollfunc_store_time stores a timestamp in the primary
trigger IRQ handler and stm32_adc_trigger_handler runs in the IRQ thread
to push out the buffer along with the timestamp.
For this to work, the driver needs to register an IIO_TIMESTAMP channel.
Do this.
For DMA, it's not as easy, because we don't push the buffers out of
stm32_adc_trigger, but out of stm32_adc_dma_buffer_done, which runs in
a tasklet scheduled after a DMA completion.
Preferably, the DMA controller would copy us the timestamp into that buffer
as well. Until this is implemented, restrict timestamping support to
only PIO. For low-frequency sampling, PIO is probably good enough.
Cc: Holger Assmann <has@pengutronix.de>
Acked-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20210125194824.30549-1-a.fatoum@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Seems that there are config combinations in which this driver gets enabled
and hence selects the MFD, but with out HAS_IOMEM getting pulled in
via some other route. MFD is entirely contained in an
if HAS_IOMEM block, leading to the build issue in this bugzilla.
https://bugzilla.kernel.org/show_bug.cgi?id=209889
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
thermal driver (Daniel Lezcano)
- Remove the notify ops as it is no longer used (Daniel Lezcano)
- Remove the 'forced passive' option and the unused bind/unbind
functions (Daniel Lezcano)
- Remove the THERMAL_TRIPS_NONE and the code cleanup around this
macro (Daniel Lezcano)
- Rework the delays to make them pre-computed instead of computing
them again and again at each polling interval (Daniel Lezcano)
- Remove the pointless 'thermal_zone_device_reset' function (Daniel
Lezcano)
- Use the critical and hot ops to prevent an unexpected system
shutdown on int340x (Kai-Heng Feng)
- Make the cooling device state private to the thermal subsystem
(Daniel Lezcano)
- Prevent to use not-power-aware actor devices with the power
allocator governor (Lukasz Luba)
- Remove 'zx' and 'tango' support along with the corresponding
platforms (Arnd Bergman)
- Fix several issues on the Omap thermal driver (Tony Lindgren)
- Add support for adc-tm5 PMIC thermal monitor for Qcom
platforms. Please note those changes rely on an immutable branch:
iio-thermal-5.11-rc1/ib-iio-thermal-5.11-rc1 from the iio tree
(Dmitry Baryshkov)
- Fix an initialization loop in the adc-tm5 (Colin Ian King)
- Fix a return error check in the cpufreq cooling device (Viresh Kumar)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAmAvkKMACgkQqDIjiipP
6E9yFggAmXy8t2j1mRvn/KLU+teTGIoSFkZ8mBnY2Sgip97IRZRhCwAZbUKOW0eI
bvpAzBjacxdZHT7OxxvGzCOq/zlAh4UoStI8bMpzdUWPdkAj4ippArLYGvagLym8
WEQysWnrr8V1RCZbQuBNjyLwjf0fcXkzIBU1mbZXA8T8Y6Yn646TdtsrVT4Idg1j
MOg7PAHBcTSY/wOReZKJ5TB1yvo2tNOuGOqUVbrIAHlRkiNTVHirVUq6aZGtTTKp
7ukcu8EI/o7XKBdQ5d9MZaHdwkcyAIJj4jdjmjkUJpa8VYQFPjayNyN3I+Py9lH2
jtWVYHQxZbY166IZP2yeXFjPzd6elw==
=Jmz4
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Use the newly introduced 'hot' and 'critical' ops for the acpi
thermal driver (Daniel Lezcano)
- Remove the notify ops as it is no longer used (Daniel Lezcano)
- Remove the 'forced passive' option and the unused bind/unbind
functions (Daniel Lezcano)
- Remove the THERMAL_TRIPS_NONE and the code cleanup around this macro
(Daniel Lezcano)
- Rework the delays to make them pre-computed instead of computing them
again and again at each polling interval (Daniel Lezcano)
- Remove the pointless 'thermal_zone_device_reset' function (Daniel
Lezcano)
- Use the critical and hot ops to prevent an unexpected system shutdown
on int340x (Kai-Heng Feng)
- Make the cooling device state private to the thermal subsystem
(Daniel Lezcano)
- Prevent to use not-power-aware actor devices with the power allocator
governor (Lukasz Luba)
- Remove 'zx' and 'tango' support along with the corresponding
platforms (Arnd Bergman)
- Fix several issues on the Omap thermal driver (Tony Lindgren)
- Add support for adc-tm5 PMIC thermal monitor for Qcom platforms
(Dmitry Baryshkov)
- Fix an initialization loop in the adc-tm5 (Colin Ian King)
- Fix a return error check in the cpufreq cooling device (Viresh Kumar)
* tag 'thermal-v5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (26 commits)
thermal: cpufreq_cooling: freq_qos_update_request() returns < 0 on error
thermal: qcom: Fix comparison with uninitialized variable channels_available
thermal: qcom: add support for adc-tm5 PMIC thermal monitor
dt-bindings: thermal: qcom: add adc-thermal monitor bindings
thermal: ti-soc-thermal: Use non-inverted define for omap4
thermal: ti-soc-thermal: Simplify polling with iopoll
thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430
thermal: ti-soc-thermal: Skip pointless register access for dra7
thermal/drivers/zx: Remove zx driver
thermal/drivers/tango: Remove tango driver
thermal: power allocator: fail binding for non-power actor devices
thermal/core: Make cooling device state change private
thermal: intel: pch: Fix unexpected shutdown at critical temperature
thermal: int340x: Fix unexpected shutdown at critical temperature
thermal/core: Remove pointless thermal_zone_device_reset() function
thermal/core: Remove ms based delay fields
thermal/core: Use precomputed jiffies for the polling
thermal/core: Precompute the delays from msecs to jiffies
thermal/core: Remove unused macro THERMAL_TRIPS_NONE
thermal/core: Remove THERMAL_TRIPS_NONE test
...
Fix an off by three orders of magnitude error in the AB8500
GPADC driver. Luckily it showed up quite quickly when trying
to make use of it. The processed reads were returning
microvolts, microamperes and microcelsius instead of millivolts,
milliamperes and millicelsius as advertised.
Cc: stable@vger.kernel.org
Fixes: 07063bbfa9 ("iio: adc: New driver for the AB8500 GPADC")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201224011700.1059659-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Seems that there are config combinations in which this driver gets enabled
and hence selects the MFD, but with out HAS_IOMEM getting pulled in
via some other route. MFD is entirely contained in an
if HAS_IOMEM block, leading to the build issue in this bugzilla.
https://bugzilla.kernel.org/show_bug.cgi?id=209889
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210124195034.22576-1-jic23@kernel.org
Add support for Thermal Monitoring part of PMIC5. This part is closely
coupled with ADC, using it's channels directly. ADC-TM support
generating interrupts on ADC value crossing low or high voltage bounds,
which is used to support thermal trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205000118.493610-3-dmitry.baryshkov@linaro.org
The ADI AXI ADC driver requires IO mem access and OF to work. This change
adds these dependencies to the Kconfig symbol of the driver.
This was also found via the lkp bot, as the
devm_platform_ioremap_resource() symbol was not found at link-time on the
S390 architecture.
Fixes: ef04070692 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210210105044.48914-1-alexandru.ardelean@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes a wrong bit mask used for the ADC's result, which was caused by an
improper usage of the GENMASK() macro. The bits higher than ADC's
resolution are undefined and if not masked out correctly, a wrong result
can be given. The GENMASK() macro indexing is zero based, so the mask has
to go from [resolution - 1 , 0].
Fixes: 7f40e06143 ("iio:adc:ad7949: Add AD7949 ADC driver family")
Signed-off-by: Wilfried Wessner <wilfried.wessner@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210208142705.GA51260@ubuntu
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ecause clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20201231085322.24398-1-vulab@iscas.ac.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Scale adcmap_100k_104ef_104fb temp values by the factor of 1000 to
remove extra multiplication in qcom_vadc_scale_therm().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-12-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All volt-temp tables here are sorted in descending order. There is no
need to accout for (unused) ascending table sorting case, so simplify
the conversion function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-11-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
qcom_vadc7_scale_hw_calib_die_temp() uses a table format different from
the rest of volt/temp conversion functions in this file. Also the
conversion functions results in non-monothonic values conversion, which
seems wrong.
Rewrite qcom_vadc7_scale_hw_calib_die_temp() to use
qcom_vadc_map_voltage_temp() directly, like the rest of conversion
functions do.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-10-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct vadc_map_pt is not used outside of qcom-vadc-common.c, so move it
there from the global header file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-9-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
qcom-vadc-common module will be used by ADC thermal monitoring driver,
so move it to global include dir.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-6-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC-TM5 driver will make use of several functions from ADC5 driver. Move
them to qcom-vadc-common driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201204025509.1075506-4-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Checking at both msm8909-pm8916.dtsi and msm8916.dtsi from downstream
it is indicated that "batt_id" channel has to be scaled with the default
function:
chan@31 {
label = "batt_id";
reg = <0x31>;
qcom,decimation = <0>;
qcom,pre-div-channel-scaling = <0>;
qcom,calibration-type = "ratiometric";
qcom,scale-function = <0>;
qcom,hw-settle-time = <0xb>;
qcom,fast-avg-setup = <0>;
};
Change LR_MUX2_BAT_ID scaling accordingly.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 7c271eea7b ("iio: adc: spmi-vadc: Changes to support different scaling")
Link: https://lore.kernel.org/r/20210113151808.4628-2-jonathan.albrieux@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the conversion was done to use devm_iio_kfifo_allocate(), a call to
iio_kfifo_free() was omitted (to be removed).
This change removes it.
Fixes: 3c53080588 ("iio: adc: ti_am335x_adc: alloc kfifo & IRQ via devm_ functions")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201203072650.24128-1-alexandru.ardelean@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2314-14 is a 14-bit, 4.5Msps, serial sampling A/D converter that draws only
6.2mA from a wide range analog supply adjustable from 2.7V to 5.25V.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Link: https://lore.kernel.org/r/20201216083639.89425-1-mircea.caprioru@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Acked-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20201218093512.871-1-vulab@iscas.ac.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The hardware conversion mode only exists in the AB8500
version of the chip, as it is lacking in the AB8505 it
will not be in the device tree and we should just not
even try to obtain it.
The driver already contains code to avoid using a
non-existing hardware conversion IRQ at conversion time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201218222013.383704-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use DIV_ROUND_CLOSEST() instead of open-coding it. This makes it more clear
what is going on for the casual reviewer.
Generated using the following the Coccinelle semantic patch.
// <smpl>
@@
expression x, y;
@@
-((x) + ((y) / 2)) / (y)
+DIV_ROUND_CLOSEST(x, y)
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201222191618.3433-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to simplify resource management and error paths in probe() and
entirely drop the remove() callback - use devres helpers wherever
possible. Define devm actions for cancelling the delayed work and
disabling the clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20201130142759.28216-4-brgl@bgdev.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We now have devm_krealloc() in the kernel Use it indstead of calling
kfree() and kcalloc() separately.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20201130142759.28216-3-brgl@bgdev.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's more elegant to use a helper local variable to store the address
of the underlying struct device than to dereference pdev everywhere.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20201130142759.28216-2-brgl@bgdev.pl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The xilinx-xadc IIO driver currently has support for the XADC in the Xilinx
7 series FPGAs. The system-monitor is the equivalent to the XADC in the
Xilinx UltraScale and UltraScale+ FPGAs.
The IP designers did a good job at maintaining backwards compatibility and
only minor changes are required to add basic support for the system-monitor
core.
The non backwards compatible changes are:
* Register map offset was moved from 0x200 to 0x400
* Only one ADC compared to two in the XADC
* 10 bit ADC instead of 12 bit ADC
* Two of the channels monitor different supplies
Add the necessary logic to accommodate these changes to support the
system-monitor in the XADC driver.
Note that this patch does not include support for some new features found
in the system-monitor like additional alarms, user supply monitoring and
secondary system-monitor access. This might be added at a later time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Anand Ashok Dumbre <anandash@xilinx.com>
Reviewed-by: Anand Ashok Dumbre <anandash@xilinx.com>
Link: https://lore.kernel.org/r/20200922134624.13191-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the missing clk_disable_unprepare() of info->pclk
before return from rockchip_saradc_resume in the error
handling case when fails to prepare and enable info->clk.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Fixes: 44d6f2ef94 ("iio: adc: add driver for Rockchip saradc")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201103120743.110662-1-miaoqinglang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
