Remove CONFIG_SOC_SAMA7 dependency to avoid having #ifdef preprocessor
directives in driver code (arch/arm/mach-at91/pm.c). This prepares the
code for next commits.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-2-claudiu.beznea@microchip.com
This adds the logic in the Felix DSA driver and Ocelot switch library.
For Ocelot switches, the DEST_IDX that is the output of the MAC table
lookup is a logical port (equal to physical port, if no LAG is used, or
a dynamically allocated number otherwise). The allocation we have in
place for LAG IDs is different from DSA's, so we can't use that:
- DSA allocates a continuous range of LAG IDs starting from 1
- Ocelot appears to require that physical ports and LAG IDs are in the
same space of [0, num_phys_ports), and additionally, ports that aren't
in a LAG must have physical port id == logical port id
The implication is that an FDB entry towards a LAG might need to be
deleted and reinstalled when the LAG ID changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Historically, the felix DSA driver has installed special traps such that
PTP over L2 works with the ocelot-8021q tagging protocol; commit
0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping") has the details.
Then the ocelot switch library also gained more comprehensive support
for PTP traps through commit 96ca08c058 ("net: mscc: ocelot: set up
traps for PTP packets").
Right now, PTP over L2 works using ocelot-8021q via the traps it has set
for itself, but nothing else does. Consolidating the two code blocks
would make ocelot-8021q gain support for PTP over L4 and tc-flower
traps, and at the same time avoid some code and TCAM duplication.
The traps are similar in intent, but different in execution, so some
explanation is required. The traps set up by felix_setup_mmio_filtering()
are VCAP IS1 filters, which have a PAG that chains them to a VCAP IS2
filter, and the IS2 is where the 'trap' action resides. The traps set up
by ocelot_trap_add(), on the other hand, have a single filter, in VCAP
IS2. The reason for chaining VCAP IS1 and IS2 in Felix was to ensure
that the hardcoded traps take precedence and cannot be overridden by the
Ocelot switch library.
So in principle, the PTP traps needed for ocelot-8021q in the Felix
driver can rely on ocelot_trap_add(), but the filters need to be patched
to account for a quirk that LS1028A has: the quirk_no_xtr_irq described
in commit 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP
timestamping"). Live-patching is done by iterating through the trap list
every time we know it has been updated, and transforming a trap into a
redirect + CPU copy if ocelot-8021q is in use.
Making the DSA ocelot-8021q tagger work with the Ocelot traps means we
can eliminate the dedicated OCELOT_VCAP_IS1_TAG_8021Q_PTP_MMIO and
OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO cookies. To minimize the patch delta,
OCELOT_VCAP_IS2_MRP_TRAP takes the place of OCELOT_VCAP_IS2_TAG_8021Q_PTP_MMIO
(the alternative would have been to left-shift all cookie numbers by 1).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switch library does not need this information, but the felix
DSA driver does.
As a reminder, the VSC9959 switch in LS1028A doesn't have an IRQ line
for packet extraction, so to be notified that a PTP packet needs to be
dequeued, it receives that packet also over Ethernet, by setting up a
packet trap. The Felix driver needs to install special kinds of traps
for packets in need of RX timestamps, such that the packets are
replicated both over Ethernet and over the CPU port module.
But the Ocelot switch library sets up more than one trap for PTP event
messages; it also traps PTP general messages, MRP control messages etc.
Those packets don't need PTP timestamps, so there's no reason for the
Felix driver to send them to the CPU port module.
By knowing which traps need PTP timestamps, the Felix driver can
adjust the traps installed using ocelot_trap_add() such that only those
will actually get delivered to the CPU port module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the ocelot-8021q tagging protocol, the CPU port isn't
configured as an NPI port, but is a regular port. So a "trap to CPU"
operation is actually a "redirect" operation. So DSA needs to set up the
trapping action one way or another, depending on the tagging protocol in
use.
To ease DSA's work of modifying the action, keep all currently installed
traps in a list, so that DSA can live-patch them when the tagging
protocol changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCELOT_VCAP_IS2_TAG_8021Q_TXVLAN overlaps with OCELOT_VCAP_IS2_MRP_REDIRECT.
To avoid this, make OCELOT_VCAP_IS2_MRP_REDIRECT take the cookie region
from N to 2 * N - 1 (where N is ocelot->num_phys_ports).
To avoid any risk that the singleton (not per port) VCAP IS2 filters
overlap with per-port VCAP IS2 filters, we must ensure that the number
of singleton filters is smaller than the number of physical ports.
This is true right now, but may change in the future as switches with
less ports get supported, or more singleton filters get added. So to be
future-proof, let's move the singleton filters at the end of the range,
where they won't overlap with anything to their right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MRP assist code installs a VCAP IS2 trapping rule for each port, but
since the key and the action is the same, just the ingress port mask
differs, there isn't any need to do this. We can save some space in the
TCAM by using a single filter and adjusting the ingress port mask.
Reuse the ocelot_trap_add() and ocelot_trap_del() functions for this
purpose.
Now that the cookies are no longer per port, we need to change the
allocation scheme such that MRP traps use a fixed number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MRP frames are configured to be trapped to the CPU queue 7, and this
number is reflected in the extraction header. However, the information
isn't used anywhere, so just leave MRP frames to go to CPU queue 0
unless needed otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every use case that needed VCAP filters (in order: DSA tag_8021q, MRP,
PTP traps) has hardcoded filter identifiers that worked well enough for
that use case alone. But when two or more of those use cases would be
used together, some of those identifiers would overlap, leading to
breakage.
Add definitions for each cookie and centralize them in ocelot_vcap.h,
such that the overlaps are more obvious.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create and utilize bulk regmap reads instead of single access for gathering
stats. The background reading of statistics happens frequently, and over
a few contiguous memory regions.
High speed PCIe buses and MMIO access will probably see negligible
performance increase. Lower speed buses like SPI and I2C could see
significant performance increase, since the bus configuration and register
access times account for a large percentage of data transfer time.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regmap supports bulk register reads. Ocelot does not. This patch adds
support for Ocelot to invoke bulk regmap reads. That will allow any driver
that performs consecutive reads over memory regions to optimize that
access.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ocelot.h file, several read / write macros were split across
multiple lines, while others weren't. Split all macros that exceed the 80
character column width and match the style of the rest of the file.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
-----BEGIN PGP SIGNATURE-----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=IMtm
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-01-27' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
[airlied: add two missing Kconfig]
drm-misc-next for v5.18:
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/456a23c6-7324-7543-0c45-751f30ef83f7@linux.intel.com
After adding device_link between the iommu consumer and smi-larb,
the pm_runtime_get(_sync) of smi-larb and smi-common will be called
automatically. we can get rid of mtk_smi_larb_get/put.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RPI_FIRMWARE_NOTIFY_DISPLAY_DONE firmware call allows to tell the
firmware the kernel is in charge of the display now and the firmware can
free whatever resources it was using.
Acked-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215095117.176435-2-maxime@cerno.tech
Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible,
or at least perform the freeing outside of the socket lock section
to decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice
and net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported
in the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or
MSM8974 (qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch
driver with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of:
lan78xx, ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer granularity,
stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KLm3
-----END PGP SIGNATURE-----
Merge tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----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=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
Add support for flushing the MAC table on a given port in the ocelot
switch library, and use this functionality in the felix DSA driver.
This operation is needed when a port leaves a bridge to become
standalone, and when the learning is disabled, and when the STP state
changes to a state where no FDB entry should be present.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only couple drivers need to get the -ENODEV error code and majority of
drivers need to explicitly initialize the performance state. Add new
common helper which sets up OPP table for these drivers.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ethernet frames can be extracted or injected autonomously to or from
the device’s DDR3/DDR3L memory and/or PCIe memory space. Linked list
data structures in memory are used for injecting or extracting Ethernet
frames. The FDMA generates interrupts when frame extraction or
injection is done and when the linked lists need updating.
The FDMA is shared between all the ethernet ports of the switch and
uses a linked list of descriptors (DCB) to inject and extract packets.
Before adding descriptors, the FDMA channels must be stopped. It would
be inefficient to do that each time a descriptor would be added so the
channels are restarted only once they stopped.
Both channels uses ring-like structure to feed the DCBs to the FDMA.
head and tail are never touched by hardware and are completely handled
by the driver. On top of that, page recycling has been added and is
mostly taken from gianfar driver.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support PTP in FDMA, PTP handling code is needed. Since
this is the same as for register-based extraction, export it with
a new ocelot_ptp_rx_timestamp() function.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
FDMA will need this code to prepare the injection frame header when
sending SKBs. Move this code into ocelot_ifh_port_set() and add
conditional IFH setting for vlan and rew op if they are not set.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a
separate file") left out an include for <soc/mscc/ocelot_vcap.h>. It was
missed because the only consumer was ocelot_vsc7514.h, which already
included ocelot_vcap.
Fixes: 32ecd22ba6 ("net: mscc: ocelot: split register definitions to a separate file")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211209074010.1813010-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move these to a separate file will allow them to be shared to other
drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC9959 switch embedded within NXP LS1028A (and that version of
Ocelot switches only) supports cut-through forwarding - meaning it can
start the process of looking up the destination ports for a packet, and
forward towards those ports, before the entire packet has been received
(as opposed to the store-and-forward mode).
The up side is having lower forwarding latency for large packets. The
down side is that frames with FCS errors are forwarded instead of being
dropped. However, erroneous frames do not result in incorrect updates of
the FDB or incorrect policer updates, since these processes are deferred
inside the switch to the end of frame. Since the switch starts the
cut-through forwarding process after all packet headers (including IP,
if any) have been processed, packets with large headers and small
payload do not see the benefit of lower forwarding latency.
There are two cases that need special attention.
The first is when a packet is multicast (or flooded) to multiple
destinations, one of which doesn't have cut-through forwarding enabled.
The switch deals with this automatically by disabling cut-through
forwarding for the frame towards all destination ports.
The second is when a packet is forwarded from a port of lower link speed
towards a port of higher link speed. This is not handled by the hardware
and needs software intervention.
Since we practically need to update the cut-through forwarding domain
from paths that aren't serialized by the rtnl_mutex (phylink
mac_link_down/mac_link_up ops), this means we need to serialize physical
link events with user space updates of bonding/bridging domains.
Enabling cut-through forwarding is done per {egress port, traffic class}.
I don't see any reason why this would be a configurable option as long
as it works without issues, and there doesn't appear to be any user
space configuration tool to toggle this on/off, so this patch enables
cut-through forwarding on all eligible ports and traffic classes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211125125808.2383984-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PSFP rules take effect on the streams from any port of VSC9959 switch.
This patch use ingress port to limit the rule only active on this port.
Each stream can only match two ingress source ports in VSC9959. Streams
from lowest port gets the configuration of SFID pointed by MAC Table
lookup and streams from highest port gets the configuration of (SFID+1)
pointed by MAC Table lookup. This patch defines the PSFP rule on highest
port as dummy rule, which means that it does not modify the MAC table.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Policer was previously automatically assigned from the highest index to
the lowest index from policer pool. But police action of tc flower now
uses index to set an police entry. This patch uses the police index to
set vcap policers, so that one policer can be shared by multiple rules.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC9959 supports Per-Stream Filtering and Policing(PSFP) that complies
with the IEEE 802.1Qci standard. The stream is identified by Null stream
identification(DMAC and VLAN ID) defined in IEEE802.1CB.
For PSFP, four tables need to be set up: stream table, stream filter
table, stream gate table, and flow meter table. Identify the stream by
parsing the tc flower keys and add it to the stream table. The stream
filter table is automatically maintained, and its index is determined by
SGID(flow gate index) and FMID(flow meter index).
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PSFP support gate and police action. This patch add the gate and police
action to flower parse action, check chain ID to determine which block
to offload. Adding psfp callback functions to add, delete and update gate
and police in PSFP table if hardware supports it.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_mact_learn_streamdata() can be used in VSC9959 to overwrite an
FDB entry with stream data. The stream data includes SFID and SSID which
can be used for PSFP and FRER set.
ocelot_mact_lookup() can be used to check if the given {DMAC, VID} FDB
entry is exist, and also can retrieve the DEST_IDX and entry type for
the FDB entry.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are all the driver updates for SoC specific drivers. There
are a couple of subsystems with individual maintainers picking up
their patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this
tree this time. There are only minor changes, but they depend
on other tegra driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process.
This depends on a small sound driver change that is included
here as well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains
a mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for
the "Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed
BMCs, something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better suspend/resume
support
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx, layerscape,
allwinner, broadcom, and omap.
-----BEGIN PGP SIGNATURE-----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=tUuj
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for the
support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver
-----BEGIN PGP SIGNATURE-----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=SVx3
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and timekeeping updates:
- No core updates
- No new clocksource/event driver
- A large rework of the ARM architected timer driver to prepare for
the support of the upcoming ARMv8.6 support
- Fix Kconfig options for Exynos MCT, Samsung PWM and TI DM timers
- Address a namespace collison in the ARC sp804 timer driver"
* tag 'timers-core-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Select TIMER_OF
clocksource/drivers/exynosy: Depend on sub-architecture for Exynos MCT and Samsung PWM
clocksource/drivers/arch_arm_timer: Move workaround synchronisation around
clocksource/drivers/arm_arch_timer: Fix masking for high freq counters
clocksource/drivers/arm_arch_timer: Drop unnecessary ISB on CVAL programming
clocksource/drivers/arm_arch_timer: Remove any trace of the TVAL programming interface
clocksource/drivers/arm_arch_timer: Work around broken CVAL implementations
clocksource/drivers/arm_arch_timer: Advertise 56bit timer to the core code
clocksource/drivers/arm_arch_timer: Move MMIO timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Fix MMIO base address vs callback ordering issue
clocksource/drivers/arm_arch_timer: Move drop _tval from erratum function names
clocksource/drivers/arm_arch_timer: Move system register timer programming over to CVAL
clocksource/drivers/arm_arch_timer: Extend write side of timer register accessors to u64
clocksource/drivers/arm_arch_timer: Drop CNT*_TVAL read accessors
clocksource/arm_arch_timer: Add build-time guards for unhandled register accesses
clocksource/drivers/arc_timer: Eliminate redefined macro error
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA would like to remove the rtnl_lock from its
SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE handlers, and the felix driver uses
the same MAC table functions as ocelot.
This means that the MAC table functions will no longer be implicitly
serialized with respect to each other by the rtnl_mutex, we need to add
a dedicated lock in ocelot for the non-atomic operations of selecting a
MAC table row, reading/writing what we want and polling for completion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a list of struct ocelot_bridge_vlan entries, we can
rewrite the pvid logic to simply point to one of those structures,
instead of having a separate structure with a "bool valid".
The NULL pointer will represent the lack of a bridge pvid (not to be
confused with the lack of a hardware pvid on the port, that is present
at all times).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the ocelot driver accepts a single egress-untagged bridge
VLAN, meaning that this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan add dev swp0 vid 2 pvid untagged
fails because the bridge automatically installs VID 1 as a pvid & untagged
VLAN, and vid 2 would be the second untagged VLAN on this port. It is
necessary to delete VID 1 before proceeding to add VID 2.
This limitation comes from the fact that we operate the port tag, when
it has an egress-untagged VID, in the OCELOT_PORT_TAG_NATIVE mode.
The ocelot switches do not have full flexibility and can either have one
single VID as egress-untagged, or all of them.
There are use cases for having all VLANs as egress-untagged as well, and
this patch adds support for that.
The change rewrites ocelot_port_set_native_vlan() into a more generic
ocelot_port_manage_port_tag() function. Because the software bridge's
state, transmitted to us via switchdev, can become very complex, we
don't attempt to track all possible state transitions, but instead take
a more declarative approach and just make ocelot_port_manage_port_tag()
figure out which more to operate in:
- port is VLAN-unaware: the classified VLAN (internal, unrelated to the
802.1Q header) is not inserted into packets on egress
- port is VLAN-aware:
- port has tagged VLANs:
-> port has no untagged VLAN: set up as pure trunk
-> port has one untagged VLAN: set up as trunk port + native VLAN
-> port has more than one untagged VLAN: this is an invalid config
which is rejected by ocelot_vlan_prepare
- port has no tagged VLANs
-> set up as pure egress-untagged port
We don't keep the number of tagged and untagged VLANs, we just count the
structures we keep.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First and foremost, the driver currently allocates a constant sized
4K * u32 (16KB memory) array for the VLAN masks. However, a typical
application might not need so many VLANs, so if we dynamically allocate
the memory as needed, we might actually save some space.
Secondly, we'll need to keep more advanced bookkeeping of the VLANs we
have, notably we'll have to check how many untagged and how many tagged
VLANs we have. This will have to stay in a structure, and allocating
another 16 KB array for that is again a bit too much.
So refactor the bridge VLANs in a linked list of structures.
The hook points inside the driver are ocelot_vlan_member_add() and
ocelot_vlan_member_del(), which previously used to operate on the
ocelot->vlan_mask[vid] array element.
ocelot_vlan_member_add() and ocelot_vlan_member_del() used to call
ocelot_vlan_member_set() to commit to the ocelot->vlan_mask.
Additionally, we had two calls to ocelot_vlan_member_set() from outside
those callers, and those were directly from ocelot_vlan_init().
Those calls do not set up bridging service VLANs, instead they:
- clear the VLAN table on reset
- set the port pvid to the value used by this driver for VLAN-unaware
standalone port operation (VID 0)
So now, when we have a structure which represents actual bridge VLANs,
VID 0 doesn't belong in that structure, since it is not part of the
bridging layer.
So delete the middle man, ocelot_vlan_member_set(), and let
ocelot_vlan_init() call directly ocelot_vlant_set_mask() which forgoes
any data structure and writes directly to hardware, which is all that we
need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch which clarifies what are the port tagging
options for Ocelot switches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In drivers/clocksource/, 3 drivers use "TIMER_CTRL_IE" with 3 different
values. Two of them (mps2-timer.c and timer-sp804.c/timer-sp.h) are
localized and left unmodifed.
One of them uses a shared header file (<soc/arc/timers.h>), which is
what is causing the "redefined" warnings, so change the macro name in
that driver only. Also change the TIMER_CTRL_NH macro name.
Both macro names are prefixed with "ARC_" to reduce the likelihood
of future name collisions.
In file included from ../drivers/clocksource/timer-sp804.c:24:
../drivers/clocksource/timer-sp.h:25: error: "TIMER_CTRL_IE" redefined [-Werror]
25 | #define TIMER_CTRL_IE (1 << 5) /* VR */
../include/soc/arc/timers.h:20: note: this is the location of the previous definition
20 | #define TIMER_CTRL_IE (1 << 0) /* Interrupt when Count reaches limit */
Fixes: b26c2e3823 ("ARC: breakout timer include code into separate header")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: linux-snps-arc@lists.infradead.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shahab Vahedi <Shahab.Vahedi@synopsys.com>
Acked-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210924020825.20317-1-rdunlap@infradead.org
Use the generic dynamic interrupt moderation (dim) framework to
implement adaptive interrupt coalescing on Rx. With the per-packet
interrupt scheme, a high interrupt rate has been noted for moderate
traffic flows leading to high CPU utilization.
The dpio driver exports new functions to enable/disable adaptive IRQ
coalescing on a DPIO object, to query the state or to update Net DIM
with a new set of bytes and frames dequeued.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DPAA2 based SoCs, the IRQ coalesing support per software portal has 2
configurable parameters:
- the IRQ timeout period (QBMAN_CINH_SWP_ITPR): how many 256 QBMAN
cycles need to pass until a dequeue interrupt is asserted.
- the IRQ threshold (QBMAN_CINH_SWP_DQRR_ITR): how many dequeue
responses in the DQRR ring would generate an IRQ.
Add support for setting up and querying these IRQ coalescing related
parameters.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the dpio_get_attributes() firmware call the dpio driver has
access to the QBMAN clock frequency. Extend the structure which holds
the firmware's response so that we can have access to this information.
This will be needed in the next patches which also add support for
interrupt coalescing which needs to be configured based on the
frequency.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This drops the use of power-domains for exposing the load_state from the
QMP driver to clients, to avoid issues related to system suspend.
SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up
Linux from suspend to perform recovery.
It adds RPM power-domain support for SM6350 and MSM8953 and base RPM
support for MSM8953 and QCM2290.
It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which
will enable the introduction of proper voltage scaling of the CPU
subsystem.
Support for releasing secondary CPUs on MSM8226 is introduced.
The Asynchronous Packet Router (APR) driver is extended to support the
new Generic Packet Router (GPR) variant, which is used to communicate
with the firmware in the new AudioReach audio driver.
Lastly it transitions a number of drivers to safer string functions, as
well as switching things to use devm_platform_ioremap_resource().
-----BEGIN PGP SIGNATURE-----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=FE4j
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=LLU7
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.16
This drops the use of power-domains for exposing the load_state from the
QMP driver to clients, to avoid issues related to system suspend.
SMP2P becomes wakeup capable, to allow dying remoteprocs to wake up
Linux from suspend to perform recovery.
It adds RPM power-domain support for SM6350 and MSM8953 and base RPM
support for MSM8953 and QCM2290.
It adds support for MSM8996, SDM630 and SDM660 in the SPM driver, which
will enable the introduction of proper voltage scaling of the CPU
subsystem.
Support for releasing secondary CPUs on MSM8226 is introduced.
The Asynchronous Packet Router (APR) driver is extended to support the
new Generic Packet Router (GPR) variant, which is used to communicate
with the firmware in the new AudioReach audio driver.
Lastly it transitions a number of drivers to safer string functions, as
well as switching things to use devm_platform_ioremap_resource().
* tag 'qcom-drivers-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (40 commits)
soc: qcom: apr: Add GPR support
soc: dt-bindings: qcom: add gpr bindings
soc: qcom: apr: make code more reuseable
soc: dt-bindings: qcom: apr: deprecate qcom,apr-domain property
soc: dt-bindings: qcom: apr: convert to yaml
dt-bindings: soc: qcom: aoss: Delete unused power-domain definitions
dt-bindings: msm/dp: Remove aoss-qmp header
soc: qcom: aoss: Drop power domain support
dt-bindings: soc: qcom: aoss: Drop the load state power-domain
soc: qcom: smp2p: Add wakeup capability to SMP2P IRQ
dt-bindings: power: rpmpd: Add SM6350 to rpmpd binding
dt-bindings: soc: qcom: aoss: Add SM6350 compatible
soc: qcom: llcc: Disable MMUHWT retention
soc: qcom: smd-rpm: Add QCM2290 compatible
dt-bindings: soc: qcom: smd-rpm: Add QCM2290 compatible
firmware: qcom_scm: Add compatible for MSM8953 SoC
dt-bindings: firmware: qcom-scm: Document msm8953 bindings
soc: qcom: pdr: Prefer strscpy over strcpy
soc: qcom: rpmh-rsc: Make use of the helper function devm_platform_ioremap_resource_byname()
soc: qcom: gsbi: Make use of the helper function devm_platform_ioremap_resource()
...
Link: https://lore.kernel.org/r/20211012173442.1017010-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sad reality is that when a PTP frame with a TX timestamping request
is transmitted, it isn't guaranteed that it will make it all the way to
the wire (due to congestion inside the switch), and that a timestamp
will be taken by the hardware and placed in the timestamp FIFO where an
IRQ will be raised for it.
The implication is that if enough PTP frames are silently dropped by the
hardware such that the timestamp ID has rolled over, it is possible to
match a timestamp to an old skb.
Furthermore, nobody will match on the real skb corresponding to this
timestamp, since we stupidly matched on a previous one that was stale in
the queue, and stopped there.
So PTP timestamping will be broken and there will be no way to recover.
It looks like the hardware parses the sequenceID from the PTP header,
and also provides that metadata for each timestamp. The driver currently
ignores this, but it shouldn't.
As an extra resiliency measure, do the following:
- check whether the PTP sequenceID also matches between the skb and the
timestamp, treat the skb as stale otherwise and free it
- if we see a stale skb, don't stop there and try to match an skb one
more time, chances are there's one more skb in the queue with the same
timestamp ID, otherwise we wouldn't have ever found the stale one (it
is by timestamp ID that we matched it).
While this does not prevent PTP packet drops, it at least prevents
the catastrophic consequences of incorrect timestamp matching.
Since we already call ptp_classify_raw in the TX path, save the result
in the skb->cb of the clone, and just use that result in the interrupt
code path.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.
The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.
The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.
The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.
Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.
Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PM stubs need to depend on ARCH_TEGRA in order to be usable for
compile-testing of tegra-cpuidle driver. Add the dependency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the ocelot driver does support the 'vlan modify' action, but
in the ingress chain, and it is offloaded to VCAP IS1. This action
changes the classified VLAN before the packet enters the bridging
service, and the bridging works with the classified VLAN modified by
VCAP IS1.
That is good for some use cases, but there are others where the VLAN
must be modified at the stage of the egress port, after the packet has
exited the bridging service. One example is simulating IEEE 802.1CB
active stream identification filters ("active" means that not only the
rule matches on a packet flow, but it is also able to change some
headers). For example, a stream is replicated on two egress ports, but
they must have different VLAN IDs on egress ports A and B.
This seems like a task for the VCAP ES0, but that currently only
supports pushing the ES0 tag A, which is specified in the rule. Pushing
another VLAN header is not what we want, but rather overwriting the
existing one.
It looks like when we push the ES0 tag A, it is actually possible to not
only take the ES0 tag A's value from the rule itself (VID_A_VAL), but
derive it from the following formula:
ES0_TAG_A = Classified VID + VID_A_VAL
Otherwise said, ES0_TAG_A can be used to increment with a given value
the VLAN ID that the packet was already classified to, and the packet
will have this value as an outer VLAN tag. This new VLAN ID value then
gets stripped on egress (or not) according to the value of the native
VLAN from the bridging service.
While the hardware will happily increment the classified VLAN ID for all
packets that match the ES0 rule, in practice this would be rather
insane, so we only allow this kind of ES0 action if the ES0 filter
contains a VLAN ID too, so as to restrict the matching on a known
classified VLAN. If we program VID_A_VAL with the delta between the
desired final VLAN (ES0_TAG_A) and the classified VLAN, we obtain the
desired behavior.
It doesn't look like it is possible with the tc-vlan action to modify
the VLAN ID but not the PCP. In hardware it is possible to leave the PCP
to the classified value, but we unconditionally program it to overwrite
it with the PCP value from the rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ocelot_flower.c calls ocelot_vcap_filter_add(), the filter has a
given filter->id.cookie. This filter is added to the block->rules list.
However, when ocelot_flower.c calls ocelot_vcap_block_find_filter_by_id()
which passes the cookie as argument, the filter is never found by
filter->id.cookie when searching through the block->rules list.
This is unsurprising, since the filter->id.cookie is an unsigned long,
but the cookie argument provided to ocelot_vcap_block_find_filter_by_id()
is a signed int, and the comparison fails.
Fixes: 50c6cc5b92 ("net: mscc: ocelot: store a namespaced VCAP filter ID")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210930125330.2078625-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the support for SAW v4.1, used in at least MSM8998,
SDM630, SDM660 and APQ variants and, while at it, also add the
configuration for the SDM630/660 Silver and Gold cluster L2
Adaptive Voltage Scaler: this is also one of the prerequisites
to allow the OSM controller to perform DCVS.
Please note that despite there are various "versions" of these
values downstream, these are the only ones that are perfectly
stable on the entire set of tested devices.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-4-angelogioacchino.delregno@somainline.org
In commit a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic
CPUidle driver") the SPM driver has been converted to a
generic CPUidle driver: that was mainly made to simplify the
driver and that was a great accomplishment;
Though, at that time, this driver was only applicable to ARM 32-bit SoCs,
lacking logic about the handling of newer generation SAW.
In preparation for the enablement of SPM features on AArch64/ARM64,
split the cpuidle-qcom-spm driver in two: the CPUIdle related
state machine (currently used only on ARM SoCs) stays there, while
the SPM communication handling lands back in soc/qcom/spm.c and
also making sure to not discard the simplifications that were
introduced in the aforementioned commit.
Since now the "two drivers" are split, the SCM dependency in the
main SPM handling is gone and for this reason it was also possible
to move the SPM initialization early: this will also make sure that
whenever the SAW CPUIdle driver is getting initialized, the SPM
driver will be ready to do the job.
Please note that the anticipation of the SPM initialization was
also done to optimize the boot times on platforms that have their
CPU/L2 idle states managed by other means (such as PSCI), while
needing SAW initialization for other purposes, like AVS control.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-2-angelogioacchino.delregno@somainline.org
These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform
support and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
QGBB6JidIP8rtEdC+LWBB8I=
=M5+N
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
There are three noteworthy updates for 32-bit arm platforms this time:
- The Microchip SAMA7 family based on Cortex-A7 gets introduced, a new
cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5 based)
SoCs.
- The ixp4xx platform (based on Intel XScale) is finally converted to
device tree, and all the old board files are getting removed now.
- The Cirrus Logic EP93xx platform loses support for the old
MaverickCrunch FPU. Support for compiling user space applications
was already removed in gcc-4.9, and the kernel support for old
applications could not be built with clang ias. After confirming
that there are no remaining users, removing this from the kernel
seemed better than adding support for unused features to clang.
There are minor updates to the aspeed, omap and samsung platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iD8DBQBhL0Bu5t5GS2LDRf4RAtYAAJ9qcN3tF8tHPPBUknXjvQVN7ESntwCfQtPu
XOVR6q993d7EZh3ATYuXVtE=
=igP/
-----END PGP SIGNATURE-----
Merge tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"There are three noteworthy updates for 32-bit arm platforms this time:
- The Microchip SAMA7 family based on Cortex-A7 gets introduced, a
new cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5
based) SoCs.
- The ixp4xx platform (based on Intel XScale) is finally converted to
device tree, and all the old board files are getting removed now.
- The Cirrus Logic EP93xx platform loses support for the old
MaverickCrunch FPU. Support for compiling user space applications
was already removed in gcc-4.9, and the kernel support for old
applications could not be built with clang ias. After confirming
that there are no remaining users, removing this from the kernel
seemed better than adding support for unused features to clang.
There are minor updates to the aspeed, omap and samsung platforms"
* tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
soc: aspeed-lpc-ctrl: Fix clock cleanup in error path
ARM: s3c: delete unneed local variable "delay"
soc: aspeed: Re-enable FWH2AHB on AST2600
soc: aspeed: socinfo: Add AST2625 variant
soc: aspeed: p2a-ctrl: Fix boundary check for mmap
soc: aspeed: lpc-ctrl: Fix boundary check for mmap
ARM: ixp4xx: Delete the Freecom FSG-3 boardfiles
ARM: ixp4xx: Delete GTWX5715 board files
ARM: ixp4xx: Delete Coyote and IXDPG425 boardfiles
ARM: ixp4xx: Delete Intel reference design boardfiles
ARM: ixp4xx: Delete Avila boardfiles
ARM: ixp4xx: Delete the Arcom Vulcan boardfiles
ARM: ixp4xx: Delete Gateway WG302v2 boardfiles
ARM: ixp4xx: Delete Omicron boardfiles
ARM: ixp4xx: Delete the D-Link DSM-G600 boardfiles
ARM: ixp4xx: Delete NAS100D boardfiles
ARM: ixp4xx: Delete NSLU2 boardfiles
arm: omap2: Drop the unused OMAP_PACKAGE_* KConfig entries
arm: omap2: Drop obsolete MACH_OMAP3_PANDORA entry
ARM: ep93xx: remove MaverickCrunch support
...
We need to transmit more restrictions in future patches, convert this
one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements runtime PM support for the FUSE block and prepares the driver
to work better in conjunction with the CPUIDLE driver.
-----BEGIN PGP SIGNATURE-----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=migJ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=GgIf
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.15-rc1
Implements runtime PM support for the FUSE block and prepares the driver
to work better in conjunction with the CPUIDLE driver.
* tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
Link: https://lore.kernel.org/r/20210813162157.2820913-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:
- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
which are written with their hardware default values, also runtime
invariants. So it makes no sense to write these during every .ndo_open.
- PORTID_VAL: this field has an out-of-reset value of zero for all ports
and must be initialized by software. Additionally, the
ocelot_setup_logical_port_ids() code path sets up different logical
port IDs for the ports in a hardware LAG, and we absolutely don't want
.ndo_open to interfere there and reset those values.
So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.
ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.
So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both PMC and cpuidle drivers are probed at the same init level and
cpuidle depends on the PMC suspend mode. Add new default suspend mode
that indicates whether PMC driver has been probed and reset the mode in
a case of deferred probe of the PMC driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
- mach-at91 entry, Kconfig and header files
- Power Management Controller (PMC) code and associated power management
changes. Support for suspend/resume, Ultra Low Power modes and
Backup with Memory in Self-Refresh mode.
- Power management association with DDR controller and
shutdown controller for addressing this variety of modes.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYQpPnQAKCRAfOrpwrNPN
DJyeAQDvS538E7jFPdsmUn3iZhMhV4zCZVsPk9fox9ptV8ewEAD/QuWFZg78YkZE
vGe/AXlxjA4V/TMiGElf0/nbZ8xLiw4=
=YucO
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=+KcA
-----END PGP SIGNATURE-----
Merge tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 soc for 5.15:
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
- mach-at91 entry, Kconfig and header files
- Power Management Controller (PMC) code and associated power management
changes. Support for suspend/resume, Ultra Low Power modes and
Backup with Memory in Self-Refresh mode.
- Power management association with DDR controller and
shutdown controller for addressing this variety of modes.
* tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (26 commits)
ARM: at91: pm: add sama7g5 shdwc
ARM: at91: pm: add pm support for SAMA7G5
ARM: at91: sama7: introduce sama7 SoC family
ARM: at91: pm: add sama7g5's pmc
ARM: at91: pm: add backup mode support for SAMA7G5
ARM: at91: pm: save ddr phy calibration data to securam
ARM: at91: pm: add sama7g5 ddr phy controller
ARM: at91: pm: add sama7g5 ddr controller
ARM: at91: pm: wait for ddr power mode off
ARM: at91: pm: add support for 2.5V LDO regulator control
ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
ARM: at91: pm: add self-refresh support for sama7g5
ARM: at91: ddr: add registers definitions for sama7g5's ddr
ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
ARM: at91: pm: add support for waiting MCK1..4
ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
ARM: at91: pm: use r7 instead of tmp1
ARM: at91: pm: do not initialize pdev
ARM: at91: pm: check for different controllers in at91_pm_modes_init()
...
Link: https://lore.kernel.org/r/20210804084316.12641-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller
driver cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining
management interfaces and communication (including bus model)
between partitions both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal
with identity mappings at boot and integration with ARM SMMU
pieces.
-----BEGIN PGP SIGNATURE-----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=kPg8
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Olof Johansson:
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller driver
cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
interfaces and communication (including bus model) between partitions
both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal with
identity mappings at boot and integration with ARM SMMU pieces.
* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
firmware: turris-mox-rwtm: show message about HWRNG registration
firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
firmware: turris-mox-rwtm: report failures better
firmware: turris-mox-rwtm: fix reply status decoding function
soc: imx: gpcv2: add support for i.MX8MN power domains
dt-bindings: add defines for i.MX8MN power domains
firmware: tegra: bpmp: Fix Tegra234-only builds
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
firmware: qcom_scm: Add MDM9607 compatible
soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
memory: emif: remove unused frequency and voltage notifiers
memory: fsl_ifc: fix leak of private memory on probe failure
memory: fsl_ifc: fix leak of IO mapping on probe failure
...
A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the end
of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing legacy
mach/* include dependencies and moving platform detection/config to
drivers/soc. Also some updates/cleanup of platform data.
- Core power domain support for Tegra platforms, and some improvements
in build test coverage by adding stubs for compile test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip.
-----BEGIN PGP SIGNATURE-----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=b6Jo
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The tegra_mc_probe_device() symbol is only available when the TEGRA_MC
Kconfig option is enabled. Provide a stub if that's not the case so that
the driver can be compile-tested.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210618111846.1286166-1-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
-----BEGIN PGP SIGNATURE-----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=g0AU
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc
soc/tegra: Changes for v5.14-rc1
These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.
* tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix Tegra234-only builds
soc/tegra: fuse: Don't return -ENOMEM when allocate lookups failed
soc/tegra: regulators: Support core domain state syncing
soc/tegra: pmc: Add driver state syncing
soc/tegra: pmc: Add core power domain
soc/tegra: fuse: Add stubs needed for compile-testing
soc/tegra: Add devm_tegra_core_dev_init_opp_table()
soc/tegra: Add stub for soc_is_tegra()
soc/tegra: regulators: Bump voltages on system reboot
regulator: core: Add regulator_sync_voltage_rdev()
Link: https://lore.kernel.org/r/20210611164437.3568059-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.
Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.
Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing stubs that will allow Tegra memory driver to be compile-tested
by kernel build bots.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As on i.MX51 and i.MX53, initialize the SoC ID based on the SoC
compatible string of the board.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.
This patch is to truely support it.
- ocelot_port_txtstamp_request()
This function handles tx timestamp request by storing
ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
and additionally for two-step timestamp storing ts_id in
OCELOT_SKB_CB(clone)->ptp_cmd.
- ocelot_ptp_rew_op()
During xmit, this function is called to get rew_op (rewriter option) by
checking skb->cb for tx timestamp request, and configure to transmitting.
Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
-----BEGIN PGP SIGNATURE-----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=+DV0
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
* tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: enable acpi support in RCPM driver
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
tty: serial: ucc_uart: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: qe: replace qe_io{read,write}* wrappers by generic io{read,write}*
soc: fsl: guts: fix comment syntax in file
soc: fsl: guts: remove unneeded semicolon
soc: fsl: qe: Use DEFINE_SPINLOCK() for spinlock
soc: fsl: qbman: Delete useless kfree code
soc: fsl: qbman: Ensure device cleanup is run for kexec
Link: https://lore.kernel.org/r/20210409205719.27927-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
-----BEGIN PGP SIGNATURE-----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=bbW2
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema. This update is not
backwards compatible (ABI break) however the broken part was added
recently (v5.11) and there are no users of it yet.
* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: memory: tegra20: mc: Convert to schema
dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
memory: tegra: Print out info-level once per driver probe
memory: tegra20: Protect debug code with a lock
memory: tegra20: Correct comment to MC_STAT registers writes
memory: tegra20: Add debug statistics
memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.
There is a new user coming with the same constant in use. It will also
make its life easier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6ac9b61786.
This commit was required because at that time, ioread/iowrite
functions were sub-optimal on powerpc/32 compared to the
architecture specific in_/out_ IO accessors.
But there are now equivalent since
commit 894fa235eb ("powerpc: inline iomap accessors").
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add debug statistics collection support. The statistics is available
via debugfs in '/sys/kernel/debug/mc/stats', it shows percent of memory
controller utilization for each memory client. This information is
intended to help with debugging of memory performance issues, it already
was proven to be useful by helping to improve memory bandwidth management
of the display driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210319130933.23261-1-digetx@gmail.com
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
1637 | void at91_pinctrl_gpio_suspend(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
1661 | void at91_pinctrl_gpio_resume(void)
| ^~~~~~~~~~~~~~~~~~~~~~~~
Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.
Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.
I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.
We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.
We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new PGID that is used not to forward frames anywhere. It is used
by MRP to make sure that MRP Test frames will not reach CPU port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a handful of new RISC-V related patches for this merge window:
* A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may catch
errors in new drivers.
* Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
* NUMA support for RISC-V, which involves making the arm64 code generic.
* Support for kasan on the vmalloc region.
* A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
* Support for allocating ASIDs.
* Preliminary support for kernels larger than 128MiB.
* Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
-----BEGIN PGP SIGNATURE-----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=CutX
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
Add a clock provider driver for the Canaan Kendryte K210 RISC-V SoC.
This new driver with the compatible string "canaan,k210-clk" implements
support for the full clock structure of the K210 SoC. Since it is
required for the correct operation of the SoC, this driver is
selected by default for compilation when the SOC_CANAAN option is
selected.
With this change, the k210-sysctl driver is turned into a simple
platform driver which enables its power bus clock and triggers
populating its child nodes. The sysctl driver retains the SOC early
initialization code, but the implementation now relies on the new
function k210_clk_early_init() provided by the new clk-k210 driver.
The clock structure implemented and many of the coding ideas for the
driver come from the work by Sean Anderson on the K210 support for the
U-Boot project.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Including:
- ARM SMMU and Mediatek updates from Will Deacon:
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance
on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built
independently from IOMMU
- Some tidy-up in IOVA and core code
- Conversion of the AMD IOMMU code to use the generic
IO-page-table framework
- Intel VT-d updates from Lu Baolu:
- Audit capability consistency among different IOMMUs
- Add SATC reporting structure support
- Add iotlb_sync_map callback support
- SDHI Support for Renesas IOMMU driver
- Misc Cleanups and other small improvments
-----BEGIN PGP SIGNATURE-----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=xSX1
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM SMMU and Mediatek updates from Will Deacon:
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU perf driver to be built independently from IOMMU
- Some tidy-up in IOVA and core code
- Conversion of the AMD IOMMU code to use the generic IO-page-table
framework
- Intel VT-d updates from Lu Baolu:
- Audit capability consistency among different IOMMUs
- Add SATC reporting structure support
- Add iotlb_sync_map callback support
- SDHI support for Renesas IOMMU driver
- Misc cleanups and other small improvments
* tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (94 commits)
iommu/amd: Fix performance counter initialization
MAINTAINERS: repair file pattern in MEDIATEK IOMMU DRIVER
iommu/mediatek: Fix error code in probe()
iommu/mediatek: Fix unsigned domid comparison with less than zero
iommu/vt-d: Parse SATC reporting structure
iommu/vt-d: Add new enum value and structure for SATC
iommu/vt-d: Add iotlb_sync_map callback
iommu/vt-d: Move capability check code to cap_audit files
iommu/vt-d: Audit IOMMU Capabilities and add helper functions
iommu/vt-d: Fix 'physical' typos
iommu: Properly pass gfp_t in _iommu_map() to avoid atomic sleeping
iommu/vt-d: Fix compile error [-Werror=implicit-function-declaration]
driver/perf: Remove ARM_SMMU_V3_PMU dependency on ARM_SMMU_V3
MAINTAINERS: Add entry for MediaTek IOMMU
iommu/mediatek: Add mt8192 support
iommu/mediatek: Remove unnecessary check in attach_device
iommu/mediatek: Support master use iova over 32bit
iommu/mediatek: Add iova reserved function
iommu/mediatek: Support for multi domains
iommu/mediatek: Add get_domain_id from dev->dma_range_map
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released()
function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not
belong into any other subsystem, most of them living in
drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=I2Zn
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.
We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.
-----BEGIN PGP SIGNATURE-----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=rWBX
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for 5.12
The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.
* tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: ocmem: don't return NULL in of_get_ocmem
soc: qcom: socinfo: Remove unwanted le32_to_cpu()
soc: qcom: aoss: Add SM8350 compatible
drivers: soc: qcom: rpmpd: Add msm8994 RPM Power Domains
soc: qcom: socinfo: Fix an off by one in qcom_show_pmic_model()
soc: qcom: socinfo: Fix off-by-one array index bounds check
soc: qcom: socinfo: Add MDM9607 IDs
soc: qcom: socinfo: Add SoC IDs for APQ/MSM8998
soc: qcom: socinfo: Add SoC IDs for 630 family
soc: qcom: socinfo: Open read access to all for debugfs
soc: qcom: socinfo: add info from PMIC models array
soc: qcom: socinfo: add several PMIC IDs
soc: qcom: socinfo: add qrb5165 SoC ID
soc: qcom: rpmh: Remove serialization of TCS commands
soc: qcom: smem: use %*ph to print small buffer
dt-bindings: soc: qcom: convert qcom,smem bindings to yaml
drivers: qcom: rpmh-rsc: Do not read back the register write on trigger
soc: qcom: llcc-qcom: Add support for SM8250 SoC
soc: qcom: llcc-qcom: Extract major hardware version
dt-bindings: msm: Add LLCC for SM8250
Link: https://lore.kernel.org/r/20210204052258.388890-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.
With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.
There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:
ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);
which should have been instead, as per the reference manual:
ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
DEV_MAC_ENA_CFG);
Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.
I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:
if (!phydev->link)
return;
therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.
Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.
Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.
Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.
In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.
We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
please pull the following:
- Rafal adds support for the Power Management Bus (PMB) which is used in
a variety of DSL/Cable modem/STB SoCs with a primary target being the
4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
get the chip identification (family and revision) to permit the
Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
- Florian removes an unused function and its header
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAmAXKTQACgkQh9CWnEQH
BwSyvxAAsOVmytMHBHxe4i8Pad0Yv9sUsV0AvfvJmi0lhd0a1L7HLWBhoYq+fNFO
R6ycuVjUb9RCA5O9nps6qnWbslEar3h5of/Ku4ovev3I5xQYiGFLOPe75ivoi+sl
I4T9PwVuWV3WDjK8upA3naUwNzEv30Zw0uFULw5J0RFZAB3W3ObITO3mF8a3aOGc
uVNWfD+Ro/2l1hrPfO74Qm0r36XQmvRNNOFH3gpKdBZAG2nHkQpfOsoNNUGjBjYm
amFqm/zfc7Ydxg2WzQwUUaslyq+yIKtn919rFnudR48iHpzpotVuFKgGt3CppCl5
oF4/1+C6bRzKErPYzn3B6JGFOYwSZwg9+TleDEv7eElIo04FBSOa6pNoHNDEfPXr
LI9U7CL0/zf8vbkoK3txQg7fdcYvwED9/ip5u2IJ8KZvhoCu175FIZbrXIO+woPC
gTk28bSBWH4mqGh7fPOmX3fBc2zow7xd/DlTnT1SNy6IVDZL9S82czAS/b2ImBzp
sfK0fDFrO3cPfrE2/CrKwT/OiMOUsrc0Al7g0rmpPkFHgnrh/ZCV+zQT7RSEvL1P
Gp3ZFkSjTbrXIZwkJ04i73sJUpC8F8F8XeoFItPs3VGXxJxsapB+b6TuW09qhkvU
WJXD3gFUL34IXI6luB1ZWNG4/fJBHgWXIrKsBnf9kpZENfHEdKs=
=43Gr
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoCs drivers changes for 5.12,
please pull the following:
- Rafal adds support for the Power Management Bus (PMB) which is used in
a variety of DSL/Cable modem/STB SoCs with a primary target being the
4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
get the chip identification (family and revision) to permit the
Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
- Florian removes an unused function and its header
* tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: Remove soc_is_brcmstb()
soc: bcm: brcmstb: add stubs for getting platform IDs
soc: bcm: add PM driver for Broadcom's PMB
dt-bindings: power: document Broadcom's PMB binding
Link: https://lore.kernel.org/r/20210131221721.685974-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.
-----BEGIN PGP SIGNATURE-----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=S32T
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers
Memory controller drivers for v5.12
1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.
* tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: mtk-smi: Allow building as module
memory: ti-aemif: Drop child node when jumping out loop
memory: mtk-smi: Use platform_register_drivers
memory: renesas-rpc-if: Add RZ/G2 to Kconfig description
dt-bindings: memory: renesas,rpc-if: Add support for RZ/G2 Series
memory: emif: Use DEFINE_SPINLOCK() for spinlock
memory: mtk-smi: Fix PM usage counter unbalance in mtk_smi ops
Link: https://lore.kernel.org/r/20210131180109.11510-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmAYD/QQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNLZjCACBK2bCmkVJfs39YeeMhHWVRyiiMpIuCvja
7WuIqeXnbtAg19hkwPqns+XYeTTnoeo/aSZUS9z8DIDUqADMES+1UUMfVf2mfL3A
VD1pGRtQezYS+rDOc5dL9m1CcJ2RRY5tfQEjK8Fnm5CItvylNXbURH1nfu1tMVW7
fn1tMNKCTnY7FkABttKyR4a1XIyFX+fPdSrqd5PjQ7D6rK2ZYrorMf55WpmQEfFu
3er4F3Xz8nJeTvswPUMNB3ibvcdICM9VcSwFHpElTq2dbHUDDz3uFQwyiXrutEmb
Xz4UGabjS/ZEPaty6y7VxdYEbD4Q2dzii57jKKtV49N36iCvkSR2
=5KXT
-----END PGP SIGNATURE-----
Merge tag 'arm-smmu-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into arm/smmu
Arm SMMU updates for 5.12
- Support for MT8192 IOMMU from Mediatek
- Arm v7s io-pgtable extensions for MT8192
- Removal of TLBI_ON_MAP quirk
- New Qualcomm compatible strings
- Allow SVA without hardware broadcast TLB maintenance on SMMUv3
- Virtualization Host Extension support for SMMUv3 (SVA)
- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
- Misc cleanups
After extending v7s, our pagetable already support iova reach
16GB(34bit). the master got the iova via dma_alloc_attrs may reach
34bits, but its HW register still is 32bit. then how to set the
bit32/bit33 iova? this depend on a SMI larb setting(bank_sel).
we separate whole 16GB iova to four banks:
bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G;
The bank number is (iova >> 32).
We will preassign which bank the larbs belong to. currently we don't
have a interface for master to adjust its bank number.
Each a bank is a iova_region which is a independent iommu-domain.
the iova range for each iommu-domain can't cross 4G.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> #for memory part
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-31-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Use the common memory header(larb-port) in the source code.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-9-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Unlike sja1105, the only other user of the software-defined tag_8021q.c
tagger format, the implementation we choose for the Felix DSA switch
driver preserves full functionality under a vlan_filtering bridge
(i.e. IP termination works through the DSA user ports under all
circumstances).
The tag_8021q protocol just wants:
- Identifying the ingress switch port based on the RX VLAN ID, as seen
by the CPU. We achieve this by using the TCAM engines (which are also
used for tc-flower offload) to push the RX VLAN as a second, outer
tag, on egress towards the CPU port.
- Steering traffic injected into the switch from the network stack
towards the correct front port based on the TX VLAN, and consuming
(popping) that header on the switch's egress.
A tc-flower pseudocode of the static configuration done by the driver
would look like this:
$ tc qdisc add dev <cpu-port> clsact
$ for eth in swp0 swp1 swp2 swp3; do \
tc filter add dev <cpu-port> egress flower indev ${eth} \
action vlan push id <rxvlan> protocol 802.1ad; \
tc filter add dev <cpu-port> ingress protocol 802.1Q flower
vlan_id <txvlan> action vlan pop \
action mirred egress redirect dev ${eth}; \
done
but of course since DSA does not register network interfaces for the CPU
port, this configuration would be impossible for the user to do. Also,
due to the same reason, it is impossible for the user to inadvertently
delete these rules using tc. These rules do not collide in any way with
tc-flower, they just consume some TCAM space, which is something we can
live with.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.
Unfortunately, a lesson learned in commit 69df578c5f ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.
The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.
There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We will be adding some private VCAP filters that should not interfere in
any way with the filters added using tc-flower. So we need to allocate
some IDs which will not be used by tc.
Currently ocelot uses an u32 id derived from the flow cookie, which in
itself is an unsigned long. This is a problem in itself, since on 64 bit
systems, sizeof(unsigned long)=8, so the driver is already truncating
these.
Create a struct ocelot_vcap_id which contains the full unsigned long
cookie from tc, as well as a boolean that is supposed to namespace the
filters added by tc with the ones that aren't.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix driver will need to preinstall some VCAP filters for its
tag_8021q implementation (outside of the tc-flower offload logic), so
these need to be exported to the common includes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have no in tree or out of tree users of this function, remove it and
the header providing its prototype.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for building the SMI driver as module. Switch MTK_SMI to
tristate, and add module_exit/module_license.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210126060055.11050-1-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The bd_mem_part member of ucc_geth_info always has the value
MEM_PART_SYSTEM, and AFAICT, there has never been any code setting it
to any other value. Moreover, muram is a somewhat precious resource,
so there's no point using that when normal memory serves just as well.
Apart from removing a lot of dead code, this is also motivated by
wanting to clean up the "store result from kmalloc() in a u32" mess.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a helper that takes a virtual address rather than the muram
offset. This will be used in a couple of places to avoid having to
store both the offset and the virtual address, as well as removing
NULL checks from the callers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow passing const-qualified pointers without requiring a cast in the
caller.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).
The following definitions can be made:
SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
# have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
# have one of these.
Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR
Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.
devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
size 129840 thtype static
Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).
Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:
devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
pool $POOL_ING th 1000
The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.
Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:
for tc in {0..7}; do
devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
type ingress pool $POOL_ING \
th 3000
done
The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add devlink integration into the mscc_ocelot switchdev driver. All
physical ports (i.e. the unused ones as well) except the CPU port module
at ocelot->num_phys_ports are registered with devlink, and that requires
keeping the devlink_port structure outside struct ocelot_port_private,
since the latter has a 1:1 mapping with a struct net_device (which does
not exist for unused ports).
Since we use devlink_port_type_eth_set to link the devlink port to the
net_device, we can as well remove the .ndo_get_phys_port_name and
.ndo_get_port_parent_id implementations, since devlink takes care of
retrieving the port name and number automatically, once
.ndo_get_devlink_port is implemented.
Note that the felix DSA driver is already integrated with devlink by
default, since that is a thing that the DSA core takes care of. This is
the reason why these devlink stubs were put in ocelot_net.c and not in
the common library. It is also the reason why ocelot::devlink is a
pointer and not a full structure embedded inside struct ocelot: because
the mscc_ocelot driver allocates that by itself (as the container of
struct ocelot, in fact), but in the case of felix, it is DSA who
allocates the devlink, and felix just propagates the pointer towards
struct ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should be moving anything that isn't DSA-specific or SoC-specific out
of the felix DSA driver, and into the common mscc_ocelot switch library.
The number of traffic classes is one of the aspects that is common
between all ocelot switches, so it belongs in the library.
This patch also makes seville use 8 TX queues, and therefore enables
prioritization via the QOS_CLASS field in the NPI injection header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We'll need to read back the watermark thresholds and occupancy from
hardware (for devlink-sb integration), not only to write them as we did
so far in ocelot_port_set_maxlen. So introduce 2 new functions in struct
ocelot_ops, similar to wm_enc, and implement them for the 3 supported
mscc_ocelot switches.
Remove the INUSE and MAXUSE unpacking helpers for the QSYS_RES_STAT
register, because that doesn't scale with the number of switches that
mscc_ocelot supports now. They have different bit widths for the
watermarks, and we need function pointers to abstract that difference
away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.
The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.
Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.
*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the header file include/soc/canaan/k210-sysctl.h to have a
common definition of the Canaan Kendryte K210 SoC system controller
registers. Simplify the k210 system controller driver code by removing
unused register bits definition. The MAINTAINERS file is updated,
adding the entry "CANAAN/KENDRYTE K210 SOC SYSTEM CONTROLLER DRIVER"
with myself listed as maintainer for this driver.
This is a preparatory patch for introducing the K210 clock driver. No
functional changes are introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
