The usb30_master_clk supports a 60Mhz frequency, but that is missing from
the table of supported frequencies. Add it.
Fixes: b5f5f525c5 (clk: qcom: Add MSM8998 Global Clock Control (GCC) driver)
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A branch clock is basically a clock that can be gated for power savings,
but is also what devices/drivers consume. Configuring a branch clock's
rate needs to be done at the source, so for all branch clocks which have
a defined parent, set CLK_SET_RATE_PARENT so that clk_set_rate() calls on
branch clocks can do what is expected. This is important as most drivers
do not check the resulting clock rate after a successful clk_set_rate()
call, thus the driver may get out of sync with the actual hardware state
and weird issues might crop up. This has been observed with issues
getting SDHCI to reliably support "fast" cards such as SDR104.
Fixes: 4807c71cc6 (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-fixes:
clk: qcom: qcs404: Fix gpll0_out_main parent
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: zynqmp: handle fixed factor param query error
clk: qcom: gcc: Fix board clock node name
clk: meson: axg: mark fdiv2 and fdiv3 as critical
clk: meson-gxbb: set fclk_div3 as CLK_IS_CRITICAL
clk: fixed-factor: fix of_node_get-put imbalance
gcc_lpass_trig_clk is not used downstream, therefore there is no reason to
expect it to be needed for clients. Let's remove it because messing with
the clock has been observed to cause Linux hangs when the qdss_clk is
initialized by rpmcc.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 4807c71cc6 (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Similar to other qcom targets, gcc_mmss_noc_cfg_ahb_clk should not be
disabled. Any mmss access depends on this clock, and its been observed
that enabling mmssnoc_axi_rpm_clk with rpmcc results in an implicit
access to mmss and will crash the system if gcc_mmss_noc_cfg_ahb_clk is
disabled.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Fixes: 4807c71cc6 (arm64: dts: Add msm8998 SoC and MTP board support)
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We duplicate the 'depends on' in almost every Kconfig here, and it's
getting out of hand now that we have tens of options for various SoC
drivers here. Let's clean it up a little by making a menuconfig for a
submenu and adding an if wrapper around the driver section.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clkref clocks for usb3, hdmi, ufs, pcie, and usb2. They are all
sourced off CXO_IN, so parent them off "xo" until a proper link to the
rpmcc can be described in DT.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Drop the halt check of the UFS symbol clocks, in accordance with other
platforms. This makes clk_disable_unused() happy and makes it possible
to turn the clocks on again without an error.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Disabling gcc_hmss_dvm_bus_clk and gcc_lpass_at_clk causes the board to
lock up, and by that preventing the kernel to boot without
clk_ignore_unused.
gcc_hmss_dvm_bus_clk is marked always-on downstream, but not referenced,
and gcc_lpass_at_clk isn't mentioned. So let's remove them until they
are needed by some client.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current list of defined resets is incomplete compared to what the
hardware implements. Enumerate the remaining resets according to the
hardware documentation.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We have this dummy factor clk in place to workaround a missing rpm clk
driver that can manage the XO clk state. Add it in to match what we do
on msm8996.
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
use devm variant for of_provider registration.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
[sboyd@kernel.org: Drop unused parent pointer]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The offsets for the defined BCR reset registers does not match the hardware
documentation. Update the values to match the hardware documentation.
Fixes: b5f5f525c5 (clk: qcom: Add MSM8998 Global Clock Control (GCC) driver)
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the lpass clock controller found on SDM845 based devices.
This would allow lpass peripheral loader drivers to control the clocks to
bring the subsystem out of reset.
LPASS clocks present on the global clock controller would be registered
with the clock framework based on the protected-clock flag. Also do not
gate these clocks if they are left unused, as the lpass clocks require
the global clock controller lpass clocks to be enabled before they are
accessed. Mark the GCC lpass clocks as CRITICAL, for the LPASS clock
access.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SPI friendly clock rates to the spi freq table.
Today it's not possible to use SPI at lower than 960Khz.
This patch adds 100/250/500/1000 kHz configs to the table.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In an earlier version of commit 453361cdd7 ("clk: qcom: Add graphics
clock controller driver for SDM845") there were 6 listed parents for
"gpu_cc_gmu_clk_src". In the version that landed there were 5.
...but "num_parents" was still left at 6. On my system this goes boom
at bootup.
Fixes: 453361cdd7 ("clk: qcom: Add graphics clock controller driver for SDM845")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Most of the time the CPU should not be touching the GX
domain on the GPU except for a very special use case when
the CPU needs to force the GX headswitch off. Add a
dummy enable function for the GX gdsc to simulate success
so that the pm_runtime reference counting is correct.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In extreme cases an individual gdsc may wish to override the
power domain enable or disable callback functions for their own
purposes. Only set the generic gdsc callback if the function pointers
are not already set.
Acked-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SDM845
based devices. This would allow graphics drivers to probe and
control their clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Collapse return in probe into less lines]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Certain firmware configurations "protect" clks and cause the entire
system to reboot when a non-secure OS such as Linux tries to read or
write protected clk registers. But other firmware configurations allow
reading or writing the same registers, and they may actually require
that the OS use the otherwise locked down clks. Support the
'protected-clocks' property by never registering these protected clks
with the common clk framework. This way, when firmware is protecting
these clks we won't have the chance to ever read or write these
registers and take down the entire system.
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Device tree node name are not supposed to have "_" in them so fix the
node name use of xo_board to xo-board
Fixes: 652f1813c1 ("clk: qcom: gcc: Add global clock controller driver for QCS404")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add rpm smd clocks, PMIC and bus clocks which are required on QCS404
for clients to vote on.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bjorn: Dropped cxo, voter clocks and static initialization]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Use updated printk format for OF node names
- Fix TI code to only search DT subnodes
- Various static analysis finds
* clk-dt-name:
clk: Convert to using %pOFn instead of device_node.name
* clk-ti-of-node:
clk: ti: fix OF child-node lookup
* clk-sa:
clk: mvebu: armada-37xx-tbg: Switch to clk_get and balance it in probe
reset: hisilicon: fix potential NULL pointer dereference
clk: cdce925: release child device nodes
clk: qcom: clk-branch: Use true and false for boolean values
- Tag various drivers with SPDX license tags
- Support dynamic frequency switching (DFS) on qcom SDM845 GCC
- Only use s2mps11 dt-binding defines instead of redefining them in the driver
- Add some more missing clks to qcom MSM8996 GCC
- Quad SPI clks on qcom SDM845
* clk-spdx:
clk: mvebu: use SPDX-License-Identifier
clk: renesas: Convert to SPDX identifiers
clk: renesas: use SPDX identifier for Renesas drivers
clk: s2mps11,s3c64xx: Add SPDX license identifiers
clk: max77686: Add SPDX license identifiers
* clk-qcom-dfs:
clk: qcom: Allocate space for NULL terimation in DFS table
clk: qcom: gcc: Register QUPv3 RCGs for DFS on SDM845
clk: qcom: Add support for RCG to register for DFS
* clk-smp2s11-include:
clk: s2mps11: Use existing defines from bindings for clock IDs
* clk-qcom-8996-missing:
clk: qcom: Add some missing gcc clks for msm8996
* clk-qcom-qspi:
clk: qcom: Add qspi (Quad SPI) clocks for sdm845
clk: qcom: Add qspi (Quad SPI) clock defines for sdm845 to header
This change removes a parent map and parent name array that
appear to be completely unreferenced.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a module license to match the license at the top of this file and
silence a build warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Krait CPU clocks are made up of a primary mux and secondary
mux for each CPU and the L2, controlled via cp15 accessors. For
Kraits within KPSSv1 each secondary mux accepts a different aux
source, but on KPSSv2 each secondary mux accepts the same aux
source.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The ACC and GCC regions present in KPSSv1 contain registers to
control clocks and power to each Krait CPU and L2. For CPUfreq
purposes probe these devices and expose a mux clock that chooses
between PXO and PLL8.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Krait clocks are made up of a series of muxes and a divider
that choose between a fixed rate clock and dedicated HFPLLs for
each CPU. Instead of using mmio accesses to remux parents, the
Krait implementation exposes the remux control via cp15
registers. Support these clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
[sboyd@kernel.org: Move hidden config to top outside of the visible qcom
config zone so that menuconfig looks nice]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Describe the HFPLLs present on IPQ806X devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Describe the HFPLLs present on MSM8960 and APQ8064 devices.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On some devices (MSM8974 for example), the HFPLLs are
instantiated within the Krait processor subsystem as separate
register regions. Add a driver for these PLLs so that we can
provide HFPLL clocks for use by the system.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
HFPLLs are the main frequency source for Krait CPU clocks. Add
support for changing the rate of these PLLs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clocks supported in global clock controller which clock the
peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
to the clock framework for the clients to be able to request for them.
Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Co-developed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bamse, vkoul: rebase and tidyup for upstream]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@kernel.org: Lowercase hex]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This is used by the QCS404 GCC driver, export it to allow that driver to
be compiled as a module..
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the global clock controller found on SDM660
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Based on CAF implementation.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[craig: rename parents to fit upstream, and other cleanups]
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@kernel.org: Rename gcc_660 to gcc_sdm660 and fix numbering of
defines to avoid duplicates]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the camera clock controller found on SDM845
based devices. This would allow camera drivers to probe and
control their clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The table allocated in clk_rcg2_dfs_populate_freq_table() is
eventually iterated over by qcom_find_freq() which assumes that the
table is NULL terminated. Allocate one extra space in the array for
the NULL termination. Initting of the NULL termination is implicit
due to kcalloc().
Fixes: cc4f6944d0 ("clk: qcom: Add support for RCG to register for DFS")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add both the interface and core clock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
QUPv3 clocks support DFS and thus register the RCGs which require support
for the same.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Use new macro, split out init structures so they
don't have to be copied]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Dynamic Frequency switch is a feature of clock controller by which request
from peripherals allows automatic switching frequency of input clock
without SW intervention. There are various performance levels associated
with a root clock. When the input performance state changes, the source
clocks and division ratios of the new performance state are loaded on to
RCG via HW and the RCG switches to new clock frequency when the RCG is in
DFS HW enabled mode.
Register the root clock generators(RCG) to switch to use the dfs clock ops
in the cases where DFS is enabled. The clk_round_rate() called by the clock
consumer would invoke the dfs determine clock ops and would read the DFS
performance level registers to identify all the frequencies supported and
update the frequency table. The DFS clock consumers would maintain these
frequency mapping and request the desired performance levels.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Rework registration logic to stop copying, change
recalc_rate() to index directly into the table if possible and fallback
to calculating on the fly with an assumed correct parent]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We've added duty cycle support to the clk API so that clk signal
duty cycle ratios can be adjusted while taking into account things
like clk dividers and clk tree hierarchy. So far only one SoC has
implemented support for this, but I expect there will be more to
come in the future.
Outside of the core, we have the usual pile of clk driver updates
and additions. The Amlogic meson driver got the most lines in the
diffstat this time around because it added support for a whole bunch
of hardware and duty cycle configuration. After that the Rockchip PX30,
Qualcomm SDM845, and Renesas SoC drivers fill in a majority of the diff.
We're left with the collection of non-critical fixes after that. Overall
it looks pretty quiet this time.
Core:
- Clk duty cycle support
- Proper CLK_SET_RATE_GATE support throughout the tree
New Drivers:
- Actions Semi Owl series S700 SoC clk driver
- Qualcomm SDM845 display clock controller
- i.MX6SX ocram_s clk support
- Uniphier NAND, USB3 PHY, and SPI clk support
- Qualcomm RPMh clk driver
- i.MX7D mailbox clk support
- Maxim 9485 Programmable Clock Generator
- Expose 32 kHz PLL on PXA SoCs
- imx6sll GPIO clk gate support
- Atmel at91 I2S audio clk support
- SI544/SI514 clk on/off support
- i.MX6UL GPIO clock gates in CCM CCGR
- Renesas Crypto Engine clocks on R-Car H3
- Renesas clk support for the new RZ/N1D SoC
- Allwinner A64 display engine clock support
- Support for Rockchip's PX30 SoC
- Amlogic Meson axg PCIe and audio clocks
- Amlogic Meson GEN CLK on gxbb, gxl and axg
Updates:
- Remove an unused variable from Exynos4412 ISP driver
- Fix a thinko bug in SCMI clk division logic
- Add missing of_node_put()s in some i.MX clk drivers
- Tegra SDMMC clk jitter improvements with high speed signaling modes
- SPDX tagging for qcom and cs2000-cp drivers
- Stop leaking con ids in __clk_put()
- Fix a corner case in fixed factor clk probing where node is in DT but
parent clk is registered much later
- Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return value
- i.MX clk init arrays removed in place of CLK_IS_CRITICAL
- Convert to CLK_IS_CRITICAL for i.MX51/53 driver
- Fix Tegra BPMP driver oops when xlating a NULL clk
- Proper default configuration for vic03 and vde clks on Tegra124
- Mark Tegra memory controller clks as critical
- Fix array bounds clamp in Tegra's emc determine_rate() op
- Ingenic i2s bit update and allow UDC clk to gate
- Fix name of aspeed SDC clk define to have only one 'CLK'
- Fix i.MX6QDL video clk parent
- Critical clk markings for qcom SDM845
- Fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
- Mark Rockchip's pclk_rkpwm_pmu as critical clock, due to it supplying
the pwm used to drive the logic supply of the rk3399 core.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlt0WD0RHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSX5jBAAlMLb0fqnuAGNJeXZDk5rsCa496LMyGWx
ku7uLA2H68SlbSQqq8FUPoCjDZkmsu2CbOX1U2/H4HFDS0pqpPiV3mZNtSeacedp
4Wf8yUB5G3xdq9QUCSX5LxMmEQoGeJ+gaTspBvM6sNvEMBR2kEMGBqUy768tnDTR
qCQ8Q1jOU6l8IdFV0SZGssmZ+oFqOyQoJVquPWPkw1+p/2f1KyYIyG5J5FXGxgcR
1XQITY/I/dShQ2wd+ZeDdt+GjZqIXQ06Pt3ruRG7HVP79Zt1XCRJd5dZ2lf+Wj8T
1ul3TWCAMYZ8gCPebLMbBGzKvQJQJcDU6DpIZsrUDN+C6z7KCS9vqeCxP9cF+3jJ
LOmA6cWE7z9Vkk9s0I0KJJ2Sw7wRoXzE5OJcwa/yousSz3s9cX+F8SAkdZs77oUF
0XnzPsvwdHI/egQ4UrsStPHM/gOFhsQqo8vvm5xaaTR2AxLKBHuPa9oUv9YpO/P5
J6FCst3qeY3Wp69fJ5/Z058OFOAt81dKXij2fZJBOO4KJy7Kse8Sz5ApybXVAbY5
lfvx+KGMITFqLYrcRIQZmlCuoHcMwI0FtHr9Ens5GXdbrJ+W+FlvP43eLCA0ZmRx
9DidemChj3k3PC3H6tbax/jzV4IIxZdyUoBJ1imL4uyhhaXp/qr45A/aGwNp8Q8a
WvkIGm3epK4=
=Mcn+
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The new and exciting feature this time around is in the clk core.
We've added duty cycle support to the clk API so that clk signal duty
cycle ratios can be adjusted while taking into account things like clk
dividers and clk tree hierarchy. So far only one SoC has implemented
support for this, but I expect there will be more to come in the
future.
Outside of the core, we have the usual pile of clk driver updates and
additions. The Amlogic meson driver got the most lines in the diffstat
this time around because it added support for a whole bunch of
hardware and duty cycle configuration. After that the Rockchip PX30,
Qualcomm SDM845, and Renesas SoC drivers fill in a majority of the
diff. We're left with the collection of non-critical fixes after that.
Overall it looks pretty quiet this time.
Core:
- Clk duty cycle support
- Proper CLK_SET_RATE_GATE support throughout the tree
New Drivers:
- Actions Semi Owl series S700 SoC clk driver
- Qualcomm SDM845 display clock controller
- i.MX6SX ocram_s clk support
- Uniphier NAND, USB3 PHY, and SPI clk support
- Qualcomm RPMh clk driver
- i.MX7D mailbox clk support
- Maxim 9485 Programmable Clock Generator
- expose 32 kHz PLL on PXA SoCs
- imx6sll GPIO clk gate support
- Atmel at91 I2S audio clk support
- SI544/SI514 clk on/off support
- i.MX6UL GPIO clock gates in CCM CCGR
- Renesas Crypto Engine clocks on R-Car H3
- Renesas clk support for the new RZ/N1D SoC
- Allwinner A64 display engine clock support
- support for Rockchip's PX30 SoC
- Amlogic Meson axg PCIe and audio clocks
- Amlogic Meson GEN CLK on gxbb, gxl and axg
Updates:
- remove an unused variable from Exynos4412 ISP driver
- fix a thinko bug in SCMI clk division logic
- add missing of_node_put()s in some i.MX clk drivers
- Tegra SDMMC clk jitter improvements with high speed signaling modes
- SPDX tagging for qcom and cs2000-cp drivers
- stop leaking con ids in __clk_put()
- fix a corner case in fixed factor clk probing where node is in DT
but parent clk is registered much later
- Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return
value
- i.MX clk init arrays removed in place of CLK_IS_CRITICAL
- convert to CLK_IS_CRITICAL for i.MX51/53 driver
- fix Tegra BPMP driver oops when xlating a NULL clk
- proper default configuration for vic03 and vde clks on Tegra124
- mark Tegra memory controller clks as critical
- fix array bounds clamp in Tegra's emc determine_rate() op
- Ingenic i2s bit update and allow UDC clk to gate
- fix name of aspeed SDC clk define to have only one 'CLK'
- fix i.MX6QDL video clk parent
- critical clk markings for qcom SDM845
- fix Stratix10 mpu_free_clk and sdmmc_free_clk parents
- mark Rockchip's pclk_rkpwm_pmu as critical clock, due to it
supplying the pwm used to drive the logic supply of the rk3399
core"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (85 commits)
clk: rockchip: Add pclk_rkpwm_pmu to PMU critical clocks in rk3399
clk: cs2000-cp: convert to SPDX identifiers
clk: scmi: Fix the rounding of clock rate
clk: qcom: Add display clock controller driver for SDM845
clk: mvebu: armada-37xx-periph: Remove unused var num_parents
clk: samsung: Remove unused mout_user_aclk400_mcuisp_p4x12 variable
clk: actions: Add S700 SoC clock support
dt-bindings: clock: Add S700 support for Actions Semi Soc's
clk: actions: Add missing REGMAP_MMIO dependency
clk: uniphier: add clock frequency support for SPI
clk: uniphier: add more USB3 PHY clocks
clk: uniphier: add NAND 200MHz clock
clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks
clk: tegra: Add sdmmc mux divider clock
clk: tegra: Refactor fractional divider calculation
clk: tegra: Fix includes required by fence_udelay()
clk: imx6sll: fix missing of_node_put()
clk: imx6ul: fix missing of_node_put()
clk: imx: add ocram_s clock for i.mx6sx
clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
...
* clk-qcom-rpmh:
: - Qualcomm RPMh clk driver
clk: qcom: clk-rpmh: Add QCOM RPMh clock driver
* clk-qcom-spdx:
: - SPDX tagging for qcom
clk: qcom: Update SPDX headers for common files
* clk-con-id-leak:
: - Stop leaking con ids in __clk_put()
clk: core: Potentially free connection id
* clk-fixed-factor-populated:
: - Fix a corner case in fixed factor clk probing where node is in DT but
: parent clk is registered much later
clk: clk-fixed-factor: Clear OF_POPULATED flag in case of failure
* clk-mvebu-periph-parent:
: - Marvell Armada 3700 clk_pm_cpu_get_parent() had an invalid return value
clk: mvebu: armada-37xx-periph: Remove unused var num_parents
clk: mvebu: armada-37xx-periph: Fix wrong return value in get_parent
Add support for the display clock controller found on SDM845
based devices. This would allow display drivers to probe and
control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Remove CLK_GET_RATE_NOCACHE everywhere]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
SPDX headers updated for common/branch/pll/regmap files.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the RPMh clock driver to control the RPMh managed clock resources on
some of the Qualcomm Technologies, Inc. SoCs.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[sboyd@kernel.org: Clean up whitespace, indentation, remove
cmd_db_ready check]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Frequency table macro is used by multiple clock drivers, move frequency
table macro to common header file.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Patch (7705bb7176 clk: qcom: mmcc-msm8996: leave all mmagic gdscs
and clocks always enabled") makes all mmgaic gdscs ALWAYS_ON.
The mmagic_bimc_gdsc is also needed to be turned on to get display
working on 8x96.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 7705bb7176 ("clk: qcom: mmcc-msm8996: leave all mmagic gdscs and clocks always enabled")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are certain clocks which needs to be always enabled for system
operation. Add support for the same by adding 'CLK_IS_CRITICAL' flag
for such clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
the mmci driver (drivers/mmc/host/mmci.c) does the following sequence:
* clk_prepare_enable()
* clk_set_rate()
on SDCx_clk which is a children of SDCx_src. SDCx_src has
CLK_SET_RATE_GATE so this sequence should not be allowed but this was not
enforced. IOW, the flag is ignored. Dropping the flag won't change
anything to the current behaviour of the platform.
CLK_SET_RATE_GATE is being fixed and enforced now. If the flag was kept,
the mmci driver would receive -EBUSY when calling clk_set_rate()
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180619134051.16726-2-jbrunet@baylibre.com
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
* clk-qcom-sdm845:
clk: qcom: Export clk_fabia_pll_configure()
clk: qcom: Add video clock controller driver for SDM845
dt-bindings: clock: Introduce QCOM Video clock bindings
clk: qcom: Add Global Clock controller (GCC) driver for SDM845
clk: qcom: Add DT bindings for SDM845 gcc clock controller
clk: qcom: Configure the RCGs to a safe source as needed
clk: qcom: Add support for BRANCH_HALT_SKIP flag for branch clocks
clk: qcom: Simplify gdsc status checking logic
clk: qcom: gdsc: Add support to poll CFG register to check GDSC state
clk: qcom: gdsc: Add support to poll for higher timeout value
clk: qcom: gdsc: Add support to reset AON and block reset logic
clk: qcom: Add support for controlling Fabia PLL
clk: qcom: Clear hardware clock control bit of RCG
Also fixup the Kconfig mess where SDM845 GCC has msm8998 in the
description and also the video Kconfig says things slightly differently
from the GCC one so just make it the same.
* clk-qcom-rpmh:
dt-bindings: clock: Introduce QCOM RPMh clock bindings
* clk-npcm7xx:
clk: npcm7xx: fix return value check in npcm7xx_clk_init()
clk: npcm7xx: add clock controller
dt-binding: clk: npcm750: Add binding for Nuvoton NPCM7XX Clock
* clk-of-parent-count:
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
soc/tegra: pmc: Use of_clk_get_parent_count() instead of open coding
soc: rockchip: power-domain: Use of_clk_get_parent_count() instead of open coding
ARM: timer-sp: Use of_clk_get_parent_count() instead of open coding
clk: Extract OF clock helpers in <linux/of_clk.h>
* clk-qcom-rcg-fix:
clk: qcom: Base rcg parent rate off plan frequency
This is used by the video clk driver on sdm845 and that's a module.
Export it to prevent module build failures.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The halt check of the UFS symbol clocks always fails, as such probing
UFS after clk_disable_unused always fails. This makes it impossible to
boot a system with the UFS phy or UFS HCD drivers compiled as modules.
Follow SDM845 and disable the halt check on these clocks.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the video clock controller found on SDM845
based devices. This would allow video drivers to probe and
control their clocks.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The USB and PCIE pipe clocks are sourced from external clocks
inside the QMP USB/PCIE PHYs. Enabling or disabling of PIPE RCG
clocks is dependent on PHY initialization sequence hence
update halt_check to BRANCH_HALT_SKIP for these clocks so
that clock status bit is not polled when enabling or disabling
the clocks. It allows to simplify PHY client driver code which
is both user and source of the pipe_clk and avoid error logging
related status check on clk_disable/enable.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There's no bus infrastructure today to handle all the mmagic bus
clocks and GDSCs needed by all the multimedia blocks in msm8996, like
mdss, video, camera and gpu. Mark all these clocks with a CLK_IS_CRITICAL
and GDSCs with a ALWAYS_ON flag for now so they are left always enabled.
This patch should be reverted at some point when we do have a bus driver
to manage these clocks and GDSCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We have atleast some instances of ALWAYS_ON gdscs, which need to
be turned ON *before* some clocks within the gdsc domain marked
with a CLK_IS_CRITICAL can be turned ON.
To facilitate this sequence, register the GDCSs (and hence handle
the ALWAYS_ON gdscs) before we register clocks (and handle the
clocks marked as CLK_IS_CRITICAL)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some GDSCs might have software control to turn them off, but we might
want to keep them enabled always, in some cases because of lack of
support in kernel to handle a graceful turning off/on of such GDSCs.
Most common instances would be the GDCSs which power up the noc/bus
fabrics, which need bus drivers to handle them and atleast support for
which is missing on all qcom SoCs.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
_freq_tbl_determine_rate uses the pre_div found in the clock plan
multiplied by the requested rate from the caller to determine the
best parent rate to set. If the requested rate is not exactly equal
to the rate that was found in the clock plan, then using the requested
rate in parent rate calculations is incorrect. For instance, if 150MHz
was requested, but 200MHz was the match found, and that plan had a
pre_div of 3, then the parent should be set to 600MHz, not 450MHz.
Signed-off-by: Evan Green <evgreen@chromium.org>
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the global clock controller found on SDM845
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There could be few clocks where the clock status bit is not
required to be polled as the clock on/off would be controlled
by enabling/disabling external source. Add support for the
same by introducing new flag named as 'BRANCH_HALT_SKIP'.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd@kernel.org: Rename flag to BRANCH_HALT_SKIP]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The code is complicated because we want to check if the GDSC is enabled
or disabled based on different bits in different registers while the
GDSC hardware is slightly different across chips. Furthermore, we poll
the status of the enable or disable state by checking if the gdsc is
enabled or not, and then comparing that to if the gdsc is being enabled
or disabled. Let's push all that into one function, so we can ask if the
status matches what we want, either on or off. Then the call site can
just ask that question, and the logic to check that state can simply
return yes or no, and not 1 or 0 or 0 or 1 depending on if we're
enabling or disabling respectively.
Tested-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some root clock generators, there could be child branches which are
controlled by an entity other than application processor subsystem. For
such RCGs, as per application processor subsystem clock driver, all of
its downstream clocks are disabled and RCG is in disabled state but in
reality downstream clocks can be left enabled before.
So in this scenario, when RCG is disabled as per clock driver's point of
view and when rate scaling request comes before downstream clock enable
request, then RCG fails to update its configuration because in reality
RCG is on and it expects its new source to already be in enable state but
in reality new source is off. In order to avoid having the RCG to go into
an invalid state, add support to update the CFG, M, N and D registers
during set_rate() without configuration update and defer the actual RCG
configuration update to be done during clk_enable() as at this point of
time, both its new parent and safe source will be already enabled and RCG
can safely switch to new parent.
During clk_disable() request, configure it to safe source as both its
parents, safe source and current parent will be enabled and RCG can
safely execute a switch.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The default behavior of the GDSC enable/disable sequence is to
poll the status bits of either the actual GDSCR or the
corresponding HW_CTRL registers.
On targets which have support for a CFG_GDSCR register, the
status bits might not show the correct state of the GDSC,
especially in the disable sequence, where the status bit
will be cleared even before the core is completely power
collapsed. On targets with this issue, poll the power on/off
bits in the CFG_GDSCR register instead to correctly determine
the GDSC state.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the global clock controller found on MSM8998
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Imran Khan <kimran@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Specify regs for alpha_plls, fix white spaces and add binding]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some gdscs, it might take longer time up to 500us for updating their
status. Update the timeout value for all GDSC polling status.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For some of the gdsc power domains, there could be need to reset the
AON logic or assert/deassert the block control reset before removing
the clamp_io. Add support for the same by introducing new flags
SW_RESET and AON_RESET. Both SW reset and AON reset requires to be
asserted for at least 1us before being de-asserted.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlrPhMARHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSVkkxAArsItSoxQV18kQlJ9S7o2z75giquXQfvy
Y/cKIIY1kz4K+qm+rpbl6PjukrSPtfM+wGmepGt+CptOdlj672viFxI7zjrd1iSy
/xJo7d5/nZxvmx0qcwYWVTCOsU+4FUUkpq5mE91KEvwny/qgRqEgWeLoWTDLBktF
MzGtBUYudjkRYLd2I31DGB3dqI0Dy9JwuEpJfCAt5h4dztml3aNjYknjQ/vUSEXL
61mSYM1fwzK8rnrjSlQqb+X0OoJ6d5Pz2uHRXnWfGlS8UOh5N9NFGKpiErLm+h/+
/FigA6f9HBeUneNf5Dnu568FHwE2FyUbZKVd40OYj3x128OnAoKUoRt68/8FQPdf
NoQb3zH3Ha1JbwWgvQ9RkWp82kYnMctrlkh6IFye/FxdfwCWA4SE/iIgJXRJbQ/K
blZz14jkXT8oISqy6nryGv3CK/RFXzVdvVa4z41xHc4cnLpNBsv1o89a+9MyTvMD
wYOnc/98/l5xYs5PvQqNrd/onE0GLIeOEtkWNXH0OACe6FOIuz5eVn4Uh8aIm0wl
+EHwHRwB7AQK+a7jwEfQ88aceAntvFlymUUcsncyCXn2s0knc5BHJPSHhoZk1tJb
Wv2Fcln3Mwjhhq9aoNxfAJf4pIqmFgdQEtwyND4GJlP55Xay5QMZVEdwnNfFDvmf
X6P2pfkBqkg=
=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
* clk-mvebu:
clk: mvebu: armada-38x: add support for missing clocks
clk: mvebu: cp110: Fix clock tree representation
* clk-phase:
clk: Don't show the incorrect clock phase
clk: update cached phase to respect the fact when setting phase
* clk-nxp:
clk: lpc32xx: Set name of regmap_config
* clk-mtk2712:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clocks for MT2712
* clk-qcom-rpmcc:
clk: qcom: rpmcc: Add support to XO buffered clocks
Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic updating of the output frequency
("frequency slewing") without need to turn off the PLL
before configuration. Add support for initial configuration
and programming sequence to control fabia PLLs.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd: Shorten code a little]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For upcoming targets like sdm845, POR value of the hardware clock control
bit is set for most of root clocks which needs to be cleared for software
to be able to control. For older targets like MSM8996, this bit is reserved
bit and having POR value as 0 so this patch will work for the older targets
too. So update the configuration mask to take care of the same to clear
hardware clock control bit.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
XO is onchip buffer clock to generate 19.2MHz.
This patch adds support to 5 XO buffer clocks found on PMIC8921,
these buffer clocks can be controlled from external pin or in
manual mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
aggre0 bus clks are not associated with any of the drivers, so its
important that these clks are always on to get peripherals on this
bus working. So mark them as critical.
Eventually when we have a proper bus driver these clks can be marked
appropriately.
Without this patch pcie on db820c is not functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 81ac38847a ("clk: qcom: Add APCS clock controller support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is now an helper function to round the rate when the
divider is read-only. Let's use it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-iproc:
clk: iproc: Minor tidy up of iproc pll data structures
clk: iproc: Allow plls to do minor rate changes without reset
clk: iproc: Fix error in the pll post divider rate calculation
clk: iproc: Allow iproc pll to runtime calculate vco parameters
* clk-mvebu:
clk: mvebu: armada-37xx-periph: Use PTR_ERR_OR_ZERO()
* clk-qcom-a53:
clk: qcom: Add APCS clock controller support
clk: qcom: Add regmap mux-div clocks support
clk: qcom: Add A53 PLL support
* clk-qcom-alpha-pll:
clk: qcom: add read-only alpha pll post divider operations
clk: qcom: support for 2 bit PLL post divider
clk: qcom: support Brammo type Alpha PLL
clk: qcom: support Huayra type Alpha PLL
clk: qcom: support for dynamic updating the PLL
clk: qcom: support for alpha mode configuration
clk: qcom: flag for 64 bit CONFIG_CTL
clk: qcom: fix 16 bit alpha support calculation
clk: qcom: support for alpha pll properties
* clk-check-ops-ptr:
clk: check ops pointer on clock register
* clk-protect-rate:
clk: fix set_rate_range when current rate is out of range
clk: add clk_rate_exclusive api
clk: cosmetic changes to clk_summary debugfs entry
clk: add clock protection mechanism to clk core
clk: use round rate to bail out early in set_rate
clk: rework calls to round and determine rate callbacks
clk: add clk_core_set_phase_nolock function
clk: take the prepare lock out of clk_core_set_parent
clk: fix incorrect usage of ENOSYS
* clk-omap:
clk: ti: Drop legacy clk-3xxx-legacy code
Add a driver for the APCS clock controller. It is part of the APCS
hardware block, which among other things implements also a combined
mux and half integer divider functionality. It can choose between a
fixed-rate clock or the dedicated APCS (A53) PLL. The source and the
divider can be set both at the same time.
This is required for enabling CPU frequency scaling on MSM8916-based
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Include rcg header for parent_map, drop
multiple unneeded includes, add COMPILE_TEST to APCS depends,
made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for hardware that can switch both parent clock and divider
at the same time. This avoids generating intermediate frequencies from
either the old parent clock and new divider or new parent clock and
old divider combinations.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Change a comment style, drop parent_map in
favor of a u32 array instead, export symbols for clk_ops and mux
function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CPUs on Qualcomm MSM8916-based platforms are clocked by two PLLs,
a primary (A53) CPU PLL and a secondary fixed-rate GPLL0. These sources
are connected to a mux and half-integer divider, which is feeding the
CPU cores.
This patch adds support for the primary CPU PLL which generates the
higher range of frequencies above 1GHz.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Move to devm provider registration,
NUL terminate frequency table, made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PCIE and NSS has MISC reset register in which single register has
multiple reset bit. The patch adds these resets with its
corresponding reset bits.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 3 general purpose clock controller which supplies
the clock in GPIO pins.
- It has Crypto Engine which has AXI, AHB and Core clocks.
Other non APSS processors can also use Crypto Engine so
these clocks are marked as VOTED clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has 6 ethernet ports which supports all ethernet speeds
from 10Mpbs to 10 Gpbs and each speed requires different clock
rates. Each port has separate TX and RX clocks. These clocks
use separate external UNIPHY PLL’s which will be registered with
separate NSS driver. The clock frequency is 125 Mhz for UNIPHY0
and 312.5 Mhz for UNIPHY1 and UNIPHY2.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has NSS (Network Switching System) which has 2 UBI cores
and hardware crypto engine. Some clocks are separate for each UBI
core and remaining NSS clocks are common. The BIAS_PLL (300 Mhz)
and BIAS_PLL_NSS_NOC (416.5 Mhz) are external fixed clocks and
will be registered from dtsi or NSS driver.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 2 instances of PCIE which uses AXI, AHB, AUX, SYS NOC
AXI and PIPE clocks.
- It has 2 instances of USB 3.0 which uses AUX, SLEEP, PIPE,
SYS NOC, mock UTMI and master clocks.
- It has 2 instances of SDCC which uses APSS and AHB clock.
SDCC1 requires ICE core clock also.
- All the PIPE clocks are external clocks which will be
registered in clock framework by PHY drivers. The enabling
and disabling of PIPE RCG clocks are dependent upon PHY
initialization sequence so BRANCH_HALT_DELAY flag is required for
these clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- GPLL2, GPLL4 and GPLL6 are general PLL clocks and parent
for all core peripherals.
- UBI PLL is mainly used by NSS (Network Switching System).
IPQ8074 has 2 instances of NSS UBI cores and UBI PLL will
be used to control the core frequency.
- NSS Crypto PLL is mainly used by NSS Crypto Engine which
supports the multiple cryptographic algorithm used in
Ethernet.
- IPQ8074 frequency plan does not require change in PLL post
dividers so marked the same as read-only.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GPLL0 uses 4 bits post divider which should be specified
in clock driver structure.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the driver assumes the register configuration value
is identical to its index in the parent map. This patch adds
the parent map field in regmap mux clock node which contains
the mapping of parent index with actual register configuration
value. If regmap node contains this parent map then the
configuration value will be taken from this
parent map instead of simply writing the index value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM dividers
which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current PLL driver only supports 4 bit PLL post divider so
modified the PLL divider operations to support 2 bit PLL
post divider.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.
Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.
This dynamic update requires the following sequence:
1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The current configuration does not fully configure PLL alpha mode
and values so this patch
1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the Alpha PLLs (like Spark and Brammo) don't have a
CONFIG_CTL_U register. Add logic to detect when PLLs don't have
this second config register and skip programming it during PLL
initialization.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated on the basis of ALPHA_BITWIDTH to make
the computation easy for 40 bit alpha. After calculating the 32
bit alpha, it is converted to 40 bit alpha by making lower bits
zero. But if actual alpha register width is less than
ALPHA_BITWIDTH, then the actual width can be used for
calculation. This also means, during the 40 bit alpha pll set
rate path, the lower alpha register is not configured
Change the code to calculate the rate and register values from
'alpha_width' instead of hard-coding it so that it can work for
the different widths that are supported.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different types of Alpha PLLs for which basic
software configuration part is common with following differences.
1. All these PLLs have the same basic registers like
PLL_MODE, L_VAL, ALPHA_VAL but some of the register offsets are
different between PLLs types.
2. The dynamic programming sequence is different in some
of the Alpha PLLs
3. Some of the PLLs don’t have 64 bit config control, 64 bit
user control, VCO configuration, etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds 12.288 MHz suport to codec digital clk, this clock.
Some external PA requires a 12.288 MHz to work.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes missing mnd_width for codec_digital clk, this is now set to
8 inline with datasheet.
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
lpaif i2s clk rates in the freq table are not accurate enough
for I2S mclk. Fix the inaccurate ones and add few more clock
rates that are used in LPASS audio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clkdiv module provides a clock output on the PMIC with CXO as
the source. This clock can be routed through PMIC GPIOs. Add
a device driver to configure this clkdiv module.
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
[sboyd: Simplified code and moved to devm clk provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
Make sure to search only the child nodes of "/clocks", rather than the
whole device-tree depth-first starting at "/clocks" when determining
whether to register a fixed clock in the legacy board-clock registration
helper.
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add all RPM controlled clocks on msm8996 platform
[srini: Fixed various issues with offsets and made names specific to msm8996]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RPM clocks were missing for MSM8660/APQ8060. For this to be
completed we need to add a special fixed rate RPM clock that is used
for the PLL4 on these SoCs. The rest of the clocks are pretty
similar to the other supported platforms.
The "active" clock pattern is mirrored in all the clocks. I guess
that the PLL4 that clocks the LPASS is actually never used as
"active only" since the low-power audio subsystem should be left
on when the CPU goes to idle, so that it can be used as a stand-alone
MP3 player type of device.
The PLL4 seems to be enabled only on behalf of the booting LPASS
Hexagon - which will cast its own vote once its booted - and as
such we only configure the active state (meaning both states will
have same configuration). The result is that PLL4 will be on
from prepare() to unprepare() regardless of what the application
CPU does.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RCGs ops for shared branches are not used now, so remove it.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have devm APIs for the reset controller and of clk hw
provider APIs we can remove the custom code here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds missing LPASS smmu clks which are required by the audio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clock bimc_gpu_clk_src is incorrectly set to use the shared rcg2
ops, which are for RCGs with child branches controlled by different
CPUs.
The result of the incorrect ops is that the GPU's PM runtime may leave
this clock set at a very low rate. Fix this issue by using the correct
rcg2 ops.
Fixes: a2e8272f3f ("clk: qcom: Add MSM8916 gpu clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As there is no way to actually query the hardware for the current clock
rate, now racalc_rate() just returns the last rate that was previously
set. But if the rate was not set yet, we return the bogus rate of 1000Hz.
The branch clocks have the same rate as their parent, so in this case we
just need to remove recalc_rate ops and then the core framework will handle
this automagically. The round_rate() is unused, so remove it as well.
Reported-by: Archit Taneja <architt@codeaurora.org>
Fixes: 00f64b5887 ("clk: qcom: Add support for SMD-RPM Clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MCLK for internal audio codec is expected to be at 9.6MHz by default.
This patch adds support to 9.6MHz to make the default case possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the global clock controller found on
the ipq8074 based devices. This includes UART, I2C, SPI etc.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make venus_gdsc parent of venus gdsc core0 and core1.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
rpm branch clk rate should requested as either 0 or 1 but not INT_MAX.
This patch fixes rate request for branch clocks during clk handoff.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
of_find_node_by_name() drops the reference to a passed device node.
It is not necessary to drop it again, and doing so may result in the
device node being released prematurely.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
