Add transfer_one_message() spi callback in order to use the QSPI interface
as a communication channel using up to 8 qspi lines (QSPI configured
in dual flash mode).
To enable this mode, both spi-rx-bus-width and spi-tx-bus-width must be
set to 8 and cs-qpios must be populated.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220823075850.575043-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware sequencer in Intel Canon Lake and beyond supports also 64k
erase command. The SPI-NOR core uses SFDP (Serial Flash Discovery
Parameter) to figure out what the chip actually supports and only issues
64k erase if it is supported.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220816125537.89389-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel SPI flash controller has been supporting two chip selects long
time already even if the most common configuration is to have a single
flash chip for the BIOS and related data. This adds support for the
second chip select if we find out that there are two flash components
(this information is available in the mandatory flash descriptor on the
first chip). The second chip is exposed as is without any partition
information.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220816130818.89600-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On architecture where reading the SRAM is slower than the pace at
controller fills it, with interrupt enabled while reading from
SRAM FIFO causes unwanted interrupt storm to CPU.
The inner "bytes to read" loop never exits and waits for the completion
so it is enough to only enable the watermark interrupt when we
are out of bytes to read, which only happens when we start the
transfer (waiting for the FIFO to fill up initially) if the SRAM
is slow.
So only using read watermark interrupt, as the current implementation
doesn't utilize the SRAM full and indirect complete read interrupt.
And disable all the read interrupts while reading from SRAM.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Link: https://lore.kernel.org/r/20220813042616.1372110-1-niravkumar.l.rabara@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD SPI controller hardware seems to expect the FIFO buffer to be
fully setup with the details of all transfers in the SPI message before
it is able to start processing the data in a reliable way.
Furthermore, it imposes a strict ordering restriction, in the sense that
all TX transfers must be handled prior any RX transfer.
Hence, let's ensure amd_spi_execute_opcode() is called only once, after
all TX transfers have been setup, and process any remaining RX transfers
afterwards, in a second iteration.
Additionally, get rid of the unnecessary AMD_SPI_XFER_TX/RX defines and
improve error handling.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220818010059.403776-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share configuration
by integrating the device clocking fully with the clock API rather than
spot fixing the one instance that was observed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmL7fVUACgkQJNaLcl1U
h9DNIAf/ThNZXWK1+ujLkCe3VW2CfOWSBQMtL1jW7vrRI2qNMoEj478wUMUZJ83R
Sl5X7w3PW7OmiJTvTzqngS+OkUUR/8Hcp8Cvcz1DJYmBV0iYOwPjinNfbB/Z77B7
4HaBOdBdMSCq6nFX7obKc4tyNGb6ZBD3YJ+PW+CRhUozfvGPXAUDoh5Eq4q1efh3
UJW5lP88Lp4zwd9rh8y05ugLFzXdxWV1LwICj2cj3+KceRwObwNfSs8Qp60iOrC+
QuSIiaZJA77BbG6y/i6Y/lZo/06ZcYAU0QzdUdaffNk+V7aadfvz2IlTHuoe186A
bV3xv1ucL2FJlrx4DAZtWp4b5EcPmA==
=xXEL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share
configuration by integrating the device clocking fully with the clock
API rather than spot fixing the one instance that was observed"
* tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: Drop Pratyush Yadav
spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
MAINTAINERS: rectify entry for ARM/HPE GXP ARCHITECTURE
spi: spi.c: Add missing __percpu annotations in users of spi_statistics
Merge series from Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>:
This patch enables the Microchip's FPGA QSPI and Polarfire SoC QSPI
controller support.
Tested spi-nand (W25N01GV) and spi-nor (MT25QL256A) on Microchip's
ICICLE kit. tested using both FPGA QSPI and Polarfie SoC QSPI.
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Fixes: 12f62a857c ("spi: lpspi: Silence error message upon deferred probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/253543c462b765eca40ba54c66f4e3fdf4acdeb7.1659735546.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
Moreover, in the case of devm_clk_get() it would only display '0' because
'ret' is know to be 0 at this point.
Fixes: cdeaf3a99a ("spi: microchip-core: switch to use dev_err_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/fb894ecec68e03fb7fc9353027c8b1a2610833d7.1659735153.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Use NULL for dma channel pointer initialization instead of plain integer.
sparse warnings: (new ones prefixed by >>)
>> drivers/spi/spi-s3c64xx.c:387:34: sparse: sparse: Using plain integer as NULL pointer
drivers/spi/spi-s3c64xx.c:388:34: sparse: sparse: Using plain integer as NULL pointer
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 82295bc0d1 ("spi: s3c64xx: move dma_release_channel to unprepare")
Fixes: f52b03c707 ("spi: s3c64xx: requests spi-dma channel only during data transfer")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220808004851.25122-1-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver for Microchip FPGA QSPI controllers. This driver also
supports "hard" QSPI controllers on Polarfire SoC.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220808064603.1174906-4-nagasuresh.relli@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shifting the recieved bit by "bits" inserts it at the top of the
*currently remaining* Tx data, so we end up accumulating the whole
transfer into bit 0 of the output word. Oops.
For the algorithm to work as intended, we need to remember where the
top of the *original* word was, and shift Rx to there.
Fixes: 1847e3046c ("spi: gpio: Implement LSB First bitbang support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/28324d8622da80461cce35a82859b003d6f6c4b0.1659538737.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of a message, the HW gets a reset in meson_spicc_unprepare_transfer(),
this resets the SPICC_CONREG register and notably the value set by the
Common Clock Framework.
This is problematic because:
- the register value CCF can be different from the corresponding CCF cached rate
- CCF is allowed to change the clock rate whenever the HW state
This introduces:
- local pow2 clock ops checking the HW state before allowing a clock operation
- separation of legacy pow2 clock patch and new enhanced clock path
- SPICC_CONREG datarate value is now value kepts across messages
It has been checked that:
- SPICC_CONREG datarate value is kept across messages
- CCF is only allowed to change the SPICC_CONREG datarate value when busy
- SPICC_CONREG datarate value is correct for each transfer
This didn't appear before commit 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
because we recalculated and wrote the rate for each xfer.
Fixes: 3e0cf4d3fc ("spi: meson-spicc: add a linear clock divider support")
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220811134445.678446-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
Here is the set of driver core and kernfs changes for 6.0-rc1.
"biggest" thing in here is some scalability improvements for kernfs for
large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed
and discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYuqCnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym/JgCcCnaycJY00ZPRQm3LQCyzfJ0HgqoAn2qxGV+K
NKycLeXZSnuvIA87dycE
=/4Jk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / kernfs updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.0-rc1.
The "biggest" thing in here is some scalability improvements for
kernfs for large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed and
discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (63 commits)
docs: embargoed-hardware-issues: fix invalid AMD contact email
firmware_loader: Replace kmap() with kmap_local_page()
sysfs docs: ABI: Fix typo in comment
kobject: fix Kconfig.debug "its" grammar
kernfs: Fix typo 'the the' in comment
docs: driver-api: firmware: add driver firmware guidelines. (v3)
arch_topology: Fix cache attributes detection in the CPU hotplug path
ACPI: PPTT: Leave the table mapped for the runtime usage
cacheinfo: Use atomic allocation for percpu cache attributes
drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist
MAINTAINERS: Change mentions of mpm to olivia
docs: ABI: sysfs-devices-soc: Update Lee Jones' email address
docs: ABI: sysfs-class-pwm: Update Lee Jones' email address
Documentation/process: Add embargoed HW contact for LLVM
Revert "kernfs: Change kernfs_notify_list to llist."
ACPI: Remove the unused find_acpi_cpu_cache_topology()
arch_topology: Warn that topology for nested clusters is not supported
arch_topology: Add support for parsing sockets in /cpu-map
arch_topology: Set cluster identifier in each core/thread from /cpu-map
arch_topology: Limit span of cpu_clustergroup_mask()
...
The big update this time around is some excellent work from David Jander
who went through the fast path and really eliminated overheads, meaning
that we are seeing a huge reduction in the time spent between transfers
for single threaded clients. Benchmarking has been coming out at about a
halving of overhead which is clearly visible in system level usage that
stresses SPI like some CAN and IIO applications, especially with small
transfers. Thanks to David for taking the time to drill down into this
and push the work upstream.
Otherwise there's been a bunch of new device support and the usual
- Optimisation of the fast path, particularly around the number and
types of locking operations, from David Jander.
- Support for Arbel NPCM845, HP GXP, Intel Meteor Lake and Thunder Bay,
MediaTek MT8188 and MT8365, Microchip FPGAs, nVidia Tegra 241 and
Samsung Exynos Auto v9 and 4210.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmLnyFYACgkQJNaLcl1U
h9AVpAf7BJI8NBQ659fyvfZkJDTlH8F3IjH4P3WpxMPCmTqvCZ5wBZyxwMIXGySE
fe7iQw3PGXBcoEHxhYPR4ePp7LO5jHePybUzGCJBD0EYhlo9QVBpD5+P4t65c9z8
Hjpul428My4L7eUGl/29iv0Qzkyd3wnVPSsZqBCB6BOPTQ+hribs93Uj6rB4wmzF
9Vu4p+dqdGvdrIj3G2KpFRtKxhpnjUeD5l8Eq3rOPlEPjSKoHADHP2ZSpxoz5jfR
8L6C+RyADs7ro7X4hiIq1TGURVJ+6EkGDdc6O+Rj0S+PL7MCVOGR0ucPZMOVmNbJ
114wnOQNmVnGKHX0IBm7VIOMkfc7Dg==
=5frj
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The big update this time around is some excellent work from David
Jander who went through the fast path and really eliminated overheads,
meaning that we are seeing a huge reduction in the time spent between
transfers for single threaded clients.
Benchmarking has been coming out at about a halving of overhead which
is clearly visible in system level usage that stresses SPI like some
CAN and IIO applications, especially with small transfers. Thanks to
David for taking the time to drill down into this and push the work
upstream.
Otherwise there's been a bunch of new device support and the usual
updates.
- Optimisation of the fast path, particularly around the number and
types of locking operations, from David Jander.
- Support for Arbel NPCM845, HP GXP, Intel Meteor Lake and Thunder
Bay, MediaTek MT8188 and MT8365, Microchip FPGAs, nVidia Tegra 241
and Samsung Exynos Auto v9 and 4210"
* tag 'spi-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (97 commits)
MAINTAINERS: add spi support to GXP
spi: dt-bindings: add documentation for hpe,gxp-spifi
spi: spi-gxp: Add support for HPE GXP SoCs
spi: a3700: support BE for AC5 SPI driver
spi/panel: dt-bindings: drop CPHA and CPOL from common properties
spi: bcm2835: enable shared interrupt support
spi: dt-bindings: spi-controller: correct example indentation
spi: dt-bindings: qcom,spi-geni-qcom: allow three interconnects
spi: npcm-fiu: Add NPCM8XX support
dt-binding: spi: Add npcm845 compatible to npcm-fiu document
spi: npcm-fiu: Modify direct read dummy configuration
spi: atmel: remove #ifdef CONFIG_{PM, SLEEP}
spi: dt-bindings: Add compatible for MediaTek MT8188
spi: dt-bindings: mediatek,spi-mtk-nor: Update bindings for nor flash
spi: dt-bindings: atmel,at91rm9200-spi: convert to json-schema
spi: tegra20-slink: fix UAF in tegra_slink_remove()
spi: Fix simplification of devm_spi_register_controller
spi: microchip-core: switch to use dev_err_probe()
spi: microchip-core: switch to use devm_spi_alloc_master()
spi: microchip-core: fix UAF in mchp_corespi_remove()
...
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
Merge series from nick.hawkins@hpe.com <nick.hawkins@hpe.com>:
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20220728161459.7738-2-nick.hawkins@hpe.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BCM2711 shares an interrupt betweem 5 SPI interfaces (0, 3, 4, 5 & 6).
Another interrupt is shared between SPI1, SPI2 and UART1, which also
affects BCM2835/6/7. Acting on an interrupt intended for another
interface ought to be harmless (although potentially inefficient), but
it can cause this driver to crash - presumably because some critical
state is not ready.
Add a test to the spi-bcm2835 interrupt service routine that
interrupts are enabled on this interface to avoid the crash and
improve efficiency.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://github.com/raspberrypi/linux/issues/5048
Suggested-by: https://github.com/boe-pi
Co-developed-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719105305.3076354-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
RSPI IP on RZ/{A, G2L} SoC's has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked.
PIO fallback does not work as interrupt signal is disabled.
This patch fixes this issue by re-enabling the interrupts by
calling dmaengine_synchronize().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220721143449.879257-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix SPI NO Slave Select macro definition, when all the SPI CS bits
are high which means no slave is selected.
Fixes: 21b511ddee ("spi: spi-cadence: Fix SPI CS gets toggling sporadically")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220713164529.28444-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding FIU NPCM8XX support to NPCM FIU driver.
NPCM8XX FIU supports four controllers.
As part of adding NPCM8XX support:
- Add NPCM8XX specific compatible string.
- Using an internal burst configuration register instead of a GCR
register.
- Support FIU1 controller.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20220718081146.256070-4-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case a IRQ based transfer times out the bcm2835_spi_handle_err()
function is called. Since commit 1513ceee70 ("spi: bcm2835: Drop
dma_pending flag") the TX and RX DMA transfers are unconditionally
canceled, leading to NULL pointer derefs if ctlr->dma_tx or
ctlr->dma_rx are not set.
Fix the NULL pointer deref by checking that ctlr->dma_tx and
ctlr->dma_rx are valid pointers before accessing them.
Fixes: 1513ceee70 ("spi: bcm2835: Drop dma_pending flag")
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220719072234.2782764-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove #ifdef CONFIG_PM, #ifdef CONFIG_PM_SLEEP and use
SYSTEM_SLEEP_PM_OPS() and RUNTIME_PM_OPS() macros instead which allows
getting also rid of __maybe_unused in the code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220718071052.1707858-1-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes: 606e5d4081 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from nandhini.srikandan@intel.com <nandhini.srikandan@intel.com>:
This patch enables support for DW SPI on Intel Thunder Bay. This patch
set also enables master mode for latest Designware SPI versions. The
driver is tested on Keem Bay and Thunder Bay evaluation board.
Merge series from Yang Yingliang <yangyingliang@huawei.com>:
Patch #1 fix a UAF in mchp_corespi_remove().
Patch #2 and #3 some cleanups to simpify code.
After calling spi_unregister_master(), the refcount of master will
be decrease to 0, and it will be freed in spi_controller_release(),
the device data also will be freed, so it will lead a UAF when using
'tspi'. To fix this, get the master before unregister and put it when
finish using it.
Fixes: 26c8634182 ("spi: tegra20-slink: Don't use resource-managed spi_register helper")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220713094024.1508869-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 59ebbe40fb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: 59ebbe40fb ("spi: simplify devm_spi_register_controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220713025657.3524506-3-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using devm_spi_register_master(), the unregister function will
be called in devres_release_all() which is called after ->remove(),
so remove spi_unregister_master() andspi_master_put().
Fixes: 9ac8d17694 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220713025657.3524506-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Intel Thunder Bay SPI controller, which uses DesignWare
DWC_ssi core and also add common init function for both Keem Bay and
Thunder Bay.
Signed-off-by: Nandhini Srikandan <nandhini.srikandan@intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220713042223.1458-5-nandhini.srikandan@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to select the controller mode as master mode by setting Bit 31
of CTRLR0 register. This feature is supported for controller versions above
v1.02.
Signed-off-by: Nandhini Srikandan <nandhini.srikandan@intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220713042223.1458-4-nandhini.srikandan@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing underscore in IP version macro to avoid compilation issue.
The macro is used for IP version comparison in the current patchset.
Fixes: 2cc8d9227b ("spi: dw: Introduce Synopsys IP-core versions interface")
Signed-off-by: Nandhini Srikandan <nandhini.srikandan@intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220713042223.1458-2-nandhini.srikandan@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SPI_BCM63XX_HSSPI depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The acpi_spi_add_resource() is never called with ctrl == NULL and
index == -1. The only caller already performs the check. Hence
remove the duplication from the acpi_spi_add_resource().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220709000709.35622-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since acpi_spi_device_alloc() has been designed to return an error
pointer we may now properly propagate error codes to the caller of
it. It helps debugging a lot.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220709000709.35622-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series addresses an issue in the spi-amd driver and, while
there, performs some additional cleanups, like simplifying the error
handling in the probe function and removing an unused struct member.
For improving code readability, it also adds some kernel-doc comments.
The io_base_addr member of struct amd_spi is not referenced anywhere
in the driver implementation and there is no indication that it could
be used in the future, hence drop it.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220706100626.1234731-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of the devm variant of spi_alloc_master() in order to cleanup
and simplify the error handling in the probe function by getting rid
of the goto statements.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220706100626.1234731-3-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling the SPI CS35L41 audio codec driver for Steam Deck [1]
revealed a problem with the current AMD SPI controller driver
implementation, consisting of an unrecoverable system hang.
The issue can be prevented if we ensure the max transfer size
and the max message size do not exceed the FIFO buffer size.
According to the implementation of the downstream driver, the
AMD SPI controller is not able to handle more than 70 bytes per
transfer, which corresponds to the size of the FIFO buffer.
Hence, let's fix this by setting the SPI limits mentioned above.
[1] https://lore.kernel.org/r/20220621213819.262537-1-cristian.ciocaltea@collabora.com
Reported-by: Anastasios Vacharakis <vacharakis@o2mail.de>
Fixes: bbb336f39e ("spi: spi-amd: Add AMD SPI controller driver support")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20220706100626.1234731-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Capitalize first word in comment where appropriate and add
parentheses to function names.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220629142519.3985486-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for LPSS SPI on Intel Meteor Lake-P. It has three
controllers each having two chip selects.
This squashes a fix from Ap, Kamal <kamal.ap@intel.com> fixing incorrect
PCI ID of 3rd controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220630073305.632850-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the normal read operation for data transfers, the dummy bus
width is zero. In that case, they are no dummy bytes to transfer and
setting the dummy field in the controller register becomes useless.
Issue was found on a custom "Bifrost" board based on the AST2500 SoC
and using a MX25L51245GMI-08G SPI Flash.
Reported-by: Ian Woloschin <ian.woloschin@akamai.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Ian Woloschin <iwolosch@akamai.com>
Fixes: 9da06d7bde ("spi: aspeed: Add support for direct mapping")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220622161617.3719096-3-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of the control register is set using the direct
mapping information passed to the ->dirmap_create() handler. Dump the
mapping range and the SPI memory operation characteristics to analyze
how the register value has been computed.
spi-aspeed-smc 1e630000.spi: CE0 read dirmap [ 0x00000000 - 0x04000000 ] OP 0x6c mode:1.1.1.4 naddr:0x4 ndummies:0x1
...
spi-aspeed-smc 1e630000.spi: CE0 write dirmap [ 0x00000000 - 0x04000000 ] OP 0x12 mode:1.1.0.1 naddr:0x4 ndummies:0x0
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220622161617.3719096-2-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Chanho Park <chanho61.park@samsung.com>:
Add to support Exynos Auto v9 SoC's spi. By supporting USI(Universal
Serial Interface) mode, the SoC can support up to 12 spi ports. Thus, we
need to increase MAX_SPI_PORTS from 6 to 12. The spi of the SoC can
support loopback mode unlike previous exynos SoCs. To separate the
feature, we need to add .has_loopback to the s3c64xx_spi_port_config.
Furthermore, it uses 4 as the default internal clock divider. We also
need to clk_div field of the structure and assign "2" as the default
value to the existing SoC's port config.
Device tree definitions of exynosautov9-spi will be added in separated
patchset to include usi(i2c/uart/spi) nodes all together.
Intel Meteor Lake-P has the same SPI serial flash controller as Alder
Lake-P. Add Meteor Lake-P PCI ID to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220629113403.79942-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add exynosautov9 spi port configuration. It supports up to 12 spis so
MAX_SPI_PORTS should be increased from 6 to 12.
It has DIV_4 as the default internal clock divider and an internal
loopback mode to run a loopback test.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629102304.65712-5-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern exynos SoCs such as Exynos Auto v9 have different internal clock
divider, for example "4". To support this internal value, this adds
clk_div of the s3c64xx_spi_port_config and assign "2" as the default
value to existing s3c64xx_spi_port_config.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220629102304.65712-3-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern exynos SoCs can support self loopback mode via setting BIT(3) of
MODE_CFG register. Previous SoCs don't have the bit so we need to add
has_loopback field in the s3c64xx_spi_port_config. Exynos Auto v9 SoC
has the bit and it will define the field to "true".
When it is set, SPI_LOOP mode will be marked.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629102304.65712-2-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from David Jander <david@protonic.nl>:
These patches optimize the spi_sync call for the common case that the
worker thread is idle and the queue is empty. It also opens the
possibility to potentially further optimize the async path also, since
it doesn't need to take into account the direct sync path anymore.
As an example for the performance gain, on an i.MX8MM SoC with a SPI CAN
controller attached (MCP2518FD), the time the interrupt line stays
active (which corresponds roughly with the time it takes to send 3
relatively short consecutive spi_sync messages) is reduced from 98us to
only 72us by this patch.
A note about message ordering:
This patch series should not change the behavior of message ordering when
coming from the same context. This means that if a client driver issues
one or more spi_async() messages immediately followed by a spi_sync()
message in the same context, it can still rely on these messages being
sent out in the order they were fired.
This fixes the sequence of dma_release_channel.
Since commit f52b03c707 ("spi: s3c64xx: requests spi-dma channel only
during data transfer"),
dma_release_channel has been located in the s3c64xx_spi_transfer_one
but this makes invalid return of can_dma callback.
__spi_unmap_msg will check whether the request is requested by dma or
not via can_dma callback. When it is calling to check it, the channels
will be already released at the end of s3c64xx_spi_transfer_one so the
callback function will return always "false". So, they can't be unmapped
from __spi_unmap_msg call. To fix this, we need to add
unprepare_transfer_hardware callback and move the dma_release_channel
from s3c64xx_spi_transfer_one to there.
Fixes: f52b03c707 ("spi: s3c64xx: requests spi-dma channel only during data transfer")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220627013845.138350-1-chanho61.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing clk_disable_unprepare() in synquacer_spi_resume().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guo Mengqi <guomengqi3@huawei.com>
Link: https://lore.kernel.org/r/20220624005614.49434-1-guomengqi3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are only a few drivers that do not call
spi_finalize_current_message() in the context of transfer_one_message(),
and even for those cases the completion ctlr->cur_msg_completion is not
needed always. The calls to complete() and wait_for_completion() each
take a spin-lock, which is costly. This patch makes it possible to avoid
those calls in the big majority of cases, by introducing two flags that
with the help of ordering via barriers can avoid using the completion
safely. In case of a race with the context calling
spi_finalize_current_message(), the scheme errs on the safe side and takes
the completion.
The impact of this patch is worth the effort: On a i.MX8MM SoC, the time
the SPI bus is idle between two consecutive calls to spi_sync(), is
reduced from 19.6us to 16.8us... roughly 15%.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-12-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces a completion that is completed in
spi_finalize_current_message() and waited for in
__spi_pump_transfer_message(). This way all manipulation of ctlr->cur_msg
is done with the io_mutex held and strictly ordered:
__spi_pump_transfer_message() will not return until
spi_finalize_current_message() is done using ctlr->cur_msg, and its
calling context is only touching ctlr->cur_msg after returning.
Due to this, we can safely drop the spin-locks around ctlr->cur_msg.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-11-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the whole idling transition is locked by the io_mutex now, there is
no need to check this flag anymore.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-7-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the idling flag is wholly behind the io_mutex, this broken piece
of code can be safely removed.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-6-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
The interaction with the controller message queue and its corresponding
auxiliary flags and variables requires the use of the queue_lock which is
costly. Since spi_sync will transfer the complete message anyway, and not
return until it is finished, there is no need to put the message into the
queue if the queue is empty. This can save a lot of overhead.
As an example of how significant this is, when using the MCP2518FD SPI CAN
controller on a i.MX8MM SoC, the time during which the interrupt line
stays active (during 3 relatively short spi_sync messages), is reduced
from 98us to 72us by this patch.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
This enables the possibility to transfer a message that is not at the
current tip of the async message queue.
This is in preparation of the next patch(es) which enable spi_sync messages
to skip the queue altogether.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-2-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
We deprecated open coding of the transfer queue back in 2017 so it's high
time we finished up converting drivers to use the standard message queue
code. The mpc52xx-psc driver is fairly straightforward so convert to use
transfer_one_message(), it looks like the driver would be a good fit for
transfer_one() with a little bit of updating but this smaller change seems
safer.
The driver seems like a good candidate for transfer_one() but the chip
select function is actually doing rather more than just updating the chip
select and both transfer_one() and transfer_one_message() are current APIs
so leave that refactoring for another day, ideally by someone with the
hardware.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220613121946.136193-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We deprecated open coding of the transfer queue back in 2017 so it's high
time we finished up converting drivers to use the standard message queue
code. The SH driver is fairly straightforward so convert to use
transfer_one_message(), it looks like the driver would be a good fit for
transfer_one() with a little bit of updating but this smaller change seems
safer.
I'm not actually clear how the driver worked robustly previously, it
clears SSA and CR1 when queueing a transfer which looks like it would
interfere with any running transfer. This clearing has been moved to the
start of the message transfer function.
I'm also unclear how exactly the chip select is managed with this driver.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220610154649.1707851-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if the source DMA device isn't ready to provide the channels
capable of the SPI DMA transfers, the DW SSI controller will be registered
with no DMA support. It isn't right since all what the driver needs to do
is to postpone the probe procedure until the DMA device is ready. Let's
fix that in the framework of the DWC SSI generic DMA implementation. First
we need to use the dma_request_chan() method instead of the
dma_request_slave_channel() function, because the later one is deprecated
and most importantly doesn't return the failure cause but the
NULL-pointer. Second we need to stop the DW SSI controller probe procedure
if the -EPROBE_DEFER error is returned on the DMA initialization. The
procedure will resume later when the channels are ready to be requested.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220624210623.6383-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Only timeout after at least one iteration of checking the
status registers. In addition, increase the transfer timeout
to 1 second.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220623140547.71762-1-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch mpc5xxx_get_bus_frequency() to use fwnode in order to help
cleaning up other parts of the kernel from OF specific code.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz> # for i2c-mpc
Acked-by: Wolfram Sang <wsa@kernel.org> # for the I2C part
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for mscan/mpc5xxx_can
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220507100147.5802-2-andriy.shevchenko@linux.intel.com
The topcliff-pch driver requires TX and RX buffers on all transfers, open
coding checks for this. Remove those open coded checks and instead rely on
the core functionality, which has the added bonus that it will fix up any
transfers submitted by drivers as needed rather than erroring out.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220615174138.4060912-1-broonie@kernel.org
Avoid pio_write process is preempted, resulting in abnormal state.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Jon <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220617124251.5051-1-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible that the error case for devm_clk_get() returns NULL,
in which case zero will be passed to PTR_ERR() as shown by the Smatch
static checker warning:
drivers/spi/spi-microchip-core.c:557 mchp_corespi_probe()
warn: passing zero to 'PTR_ERR'
Remove the NULL check and carry on with a dummy clock in case of an
error. To avoid a potential div zero, abort calculating clkgen if
clk_get_rate(spi->clk) is zero.
Fixes: 9ac8d17694 ("spi: add support for microchip fpga spi controllers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/linux-spi/20220615091633.GI2168@kadam/
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220615142028.2991915-1-conor.dooley@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -ENOMEM if the allocation fails. Don't return success.
Fixes: 6598b91b5a ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yqh6bdNYO2XNhPBa@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
There are pointers being set to null using use. Use NULL instead.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220612203428.2754823-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the unreasonable clk_prepare_enable() with clk_disable_unprepare()
before return from mchp_corespi_probe() in the error handling case.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220611021117.40494-1-wupeng58@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra Grace and later chips can support upto 4 chip select lines
for QUAD SPI. Added new compatible for Tegra Grace.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20220607114659.54314-2-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
The following series adds runtime PM support for atmel-quadspi driver.
clk_disable()/clk_enable() is called on proper
runtime_suspend()/runtime_resume() ops. Along with it 2 minor cleanups
were added (patches 2/3, 3/3).
We have already a helper to get the first child device, use it and
drop custom approach.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220610120219.18988-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32 bit systems, the following kernel BUG is hit:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x18/0x24
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc1-00001-g6ae0aec8a366 #181
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
dump_backtrace from show_stack+0x20/0x24
r7:81024ffd r6:00000000 r5:81024ffd r4:60000013
show_stack from dump_stack_lvl+0x60/0x78
dump_stack_lvl from dump_stack+0x14/0x1c
r7:81024ffd r6:80f652de r5:80bec180 r4:819a2500
dump_stack from check_preemption_disabled+0xc8/0xf0
check_preemption_disabled from debug_smp_processor_id+0x18/0x24
r8:8119b7e0 r7:81205534 r6:819f5c00 r5:819f4c00 r4:c083d724
debug_smp_processor_id from __spi_sync+0x78/0x220
__spi_sync from spi_sync+0x34/0x4c
r10:bb7bf4e0 r9:c083d724 r8:00000007 r7:81a068c0 r6:822a83c0 r5:c083d724
r4:819f4c00
spi_sync from spi_mem_exec_op+0x338/0x370
r5:000000b4 r4:c083d910
spi_mem_exec_op from spi_nor_read_id+0x98/0xdc
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:82358040
r4:819f7c40
spi_nor_read_id from spi_nor_detect+0x38/0x114
r7:82358040 r6:00000000 r5:819f7c40 r4:819f7c40
spi_nor_detect from spi_nor_scan+0x11c/0xbec
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:c083da4c r6:00000000 r5:00010101
r4:819f7c40
spi_nor_scan from spi_nor_probe+0x10c/0x2d0
r10:bb7bf4e0 r9:bb7bf4d0 r8:00000000 r7:819f4c00 r6:00000000 r5:00000000
r4:819f7c40
per-cpu access needs to be guarded against preemption.
Fixes: 6598b91b5a ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220609121334.2984808-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch has been tested on Unmatched using pm_test. The Unmatched board
uses SD over SPI and it was tested by initiating S2RAM cycles for all
devices while reading/writing files at the same time. We found no dropped
connection to the card or corrupted filesystem during test cycles.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20220610074459.3261383-2-andy.chiu@sifive.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for atmel-quadspi which will disable/enable
QSPI clocks on proper runtime_suspend/runtime_resume ops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220609084246.1795419-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return boolean values ("true" or "false") instead of 1 or 0 from bool
function.
As reported by coccicheck:
./drivers/spi/spi-s3c64xx.c:385:9-10: WARNING: return of 0/1 in function
's3c64xx_spi_can_dma' with return type bool
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220609071250.59509-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove .owner field if calls are used which set it automatically.
Eliminate the following coccicheck warning:
./drivers/spi/spi-microchip-core.c:624:3-8: No need to set .owner here.
The core will do it.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220609055533.95866-1-yang.lee@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in a dev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20220608081912.2083086-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-ti-qspi driver initializes its spi clock by the
spi-max-frequency property from the controller node, and ignores
per-transfer (and per-slave) speed_hz settings.
Isolate clock settings out from ti_qspi_setup() and call it from
ti_qspi_start_transfer_one() and ti_qspi_exec_mem_op(), using
per-transfer speed_hz and per-slave max_speed_hz settings.
Also drop spi_max_frequency from struct ti_qspi and use spi_master's
max_speed_hz.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Link: https://lore.kernel.org/r/20220519.084604.966119051165023533.atsushi.nemoto@sord.co.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
This change gives a dramatic performance improvement in the hot path,
since many costly spin_lock_irqsave() calls can be avoided.
On an i.MX8MM system with a MCP2518FD CAN controller connected via SPI,
the time the driver takes to handle interrupts, or in other words the time
the IRQ line of the CAN controller stays low is mainly dominated by the
time it takes to do 3 relatively short sync SPI transfers. The effect of
this patch is a reduction of this time from 136us down to only 98us.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220524091808.2269898-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
ZynqMP GQSPI controller can support up to two chip selects but the current
GQSPI driver only support CS0. With this update and num-cs DT property set
to 2 GQSPI driver can now support two slave devices each connected to one
chip select.
GQSPI driver configures the Lower CS and Upper CS based on the reg DT
property.
Changes tested on ZynqMP board with two SPI-NOR flashes each connected
to a different CS.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220512145820.20425-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Trimmed backtrace during failure:
refcount_t: underflow; use-after-free.
pc : refcount_warn_saturate+0xf4/0x144
Call trace:
refcount_warn_saturate
kobject_put
put_device
devm_spi_release_controller
devres_release_all
This commit makes relevant changes to remove spi_master_put() from probe
failure path.
Fixes: 606e5d4081 ("spi: cadence-quadspi: Handle spi_unregister_master() in remove()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220601071611.11853-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current s3c64xx SPI driver acquires DMA channel during driver
probe and holds on it even when channels are not used
(no DMA transfer). This is a problem especially when all the
DMA channels are exhausted (as other IPs on the same DMA
controller also acquires DMA channel) and if a new IP/Device
requests for a DMA channel (on the same DMA controller), it won’t
get DMA channel allocated.
The said issue can be avoided if s3c64xx driver request and
release DMA channel before and after data transfer. Let’s modify
the driver to request and release DMA channel before and after
DMA mode data transfer.
Signed-off-by: Adithya K V <adithya.kv@samsung.com>
Link: https://lore.kernel.org/r/20220524140132.59300-1-adithya.kv@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_alloc_master() call is not undone in all error handling paths.
Moreover, there is no .remove function to release the allocated memory.
In order to fix both this issues, switch to devm_spi_alloc_master().
This allows further simplification of the probe.
Fixes: ba2fc167e9 ("spi: altera: Add DFL bus driver for Altera API Controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0607bb59f4073f86abe5c585d35245aef0b045c6.1653805901.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
In spi_mem_exec_op(), in case cs_gpiod descriptor is set, exec_op()
callback can't be used.
The same must be applied in spi_mem_poll_status(), poll_status()
callback can't be used, we must use the legacy path using
read_poll_timeout().
Tested on STM32mp257c-ev1 specific evaluation board on which a
spi-nand was mounted instead of a spi-nor.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220602091022.358127-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The depth of the transmit FIFO for the Cadence SPI controller is currently
hardcoded to 128. But the depth is a synthesis configuration parameter of
the core and can vary between different SoCs.
If the configured FIFO size is less than 128 the driver will busy loop in
the cdns_spi_fill_tx_fifo() function waiting for FIFO space to become
available.
Depending on the length and speed of the transfer it can spin for a
significant amount of time. The cdns_spi_fill_tx_fifo() function is called
from the drivers interrupt handler, so it can leave interrupts disabled for
a prolonged amount of time.
In addition the read FIFO will also overflow and data will be discarded.
To avoid this detect the actual size of the FIFO and use that rather than
the hardcoded value.
To detect the FIFO size the FIFO threshold register is used. The register
is sized so that it can hold FIFO size - 1 as its maximum value. Bits that
are not needed to hold the threshold value will always read 0. By writing
0xffff to the register and then reading back the value in the register we
get the FIFO size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220527091143.3780378-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of unprepare_transfer_hardware, SPI controller will be disabled
which will indirectly deassert the CS line. This will create a problem
in some of the devices where message will be transferred with
cs_change flag set(CS should not be deasserted).
As per SPI controller implementation, if SPI controller is disabled then
all output enables are inactive and all pins are set to input mode which
means CS will go to default state high(deassert). This leads to an issue
when core explicitly ask not to deassert the CS (cs_change = 1). This
patch fix the above issue by checking the Slave select status bits from
configuration register before disabling the SPI.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220606062525.18447-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the set of driver core changes for 5.19-rc1.
Note, I'm not really happy with this pull request as-is, see below for
details, but overall this is all good for everything but a small set of
systems, which we have a fix for already.
Lots of tiny driver core changes and cleanups happened this cycle,
but the two major things were:
- firmware_loader reorganization and additions including the
ability to have XZ compressed firmware images and the ability
for userspace to initiate the firmware load when it needs to,
instead of being always initiated by the kernel. FPGA devices
specifically want this ability to have their firmware changed
over the lifetime of the system boot, and this allows them to
work without having to come up with yet-another-custom-uapi
interface for loading firmware for them.
- physical location support added to sysfs so that devices that
know this information, can tell userspace where they are
located in a common way. Some ACPI devices already support
this today, and more bus types should support this in the
future.
Smaller changes included:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten any
linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request if you want to take them directly, _OR_ I can just revert
the probe timeout changes and they can wait for the next -rc1 merge
cycle. Given that the fixes are tested, and pretty simple, I'm leaning
toward that choice. Sorry this all came at the end of the merge window,
I should have resolved this all 2 weeks ago, that's my fault as it was
in the middle of some travel for me.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time outs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnv/A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk/fACgvmenbo5HipqyHnOmTQlT50xQ9EYAn2eTq6ai
GkjLXBGNWOPBa5cU52qf
=yEi/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
A couple of fixes that came in during the merge window, a driver
fix for spurious timeouts in the fsi driver and an improvement to
make the core display error messages for transfer_one_message()
to help people debug things.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKXHOwACgkQJNaLcl1U
h9Cxtgf+KCYOZovyBpvHaGuwUrf5fJ3SEbS5BaEhGjyQfTSeSbZuct0+gREJbBu4
AkEOt1/VXWm3EILFbLJV1xsvIj7xhQMwGRhoKEAZ0wjtV/YK2IMC6ISvrDZL2Prr
+A/p5PJu0dHLFlOUfKbkEMa2Ez/Gm/BUR6sfCzswqG6qebRcVF6svctZ/gm+Dqvy
cBvJxqIbSdYwzAqkbrTCZiQgbtJrntagaP4WtpReTMpqrLuXD/VBFK8anzhVsREz
wCTFBi0tSSe6yXOgtGc1Gzvj2wFZ2LRGPvV7nLSfQ2YaruoSM1rwo/xPxtWxsn85
MK8dp1L5d0j7LKzG2q/gPhih0oA1Bg==
=gf5o
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes that came in during the merge window: a driver fix
for spurious timeouts in the fsi driver and an improvement to make the
core display error messages for transfer_one_message() to help people
debug things"
* tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: core: Display return code when failing to transfer message
spi: fsi: Fix spurious timeout
This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which
is the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of the
mach/*.h headers to allow the platform to be part of a generic ARMv4/v5
multiplatform kernel. The last bit that enables this support is still
missing here while we wait for some last dependencies to make it into
the mainline kernel through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets completed
here along with a few additional cleanup. At the same time, the s3c24xx
and s3c64xx are now deprecated and expected to get removed in the future.
The PXA and OMAP1 bits are in a separate branch because of dependencies.
Once both branches are merged, only the three Intel StrongARM platforms
(RiscPC, Footbridge/NetWinder and StrongARM1100) need separate kernels,
and there are no plans to include these.
-----BEGIN PGP SIGNATURE-----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=CTtN
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
All the other calls to the controller driver display the error
return code. The return code is helpful to understand what went
wrong, so include it when failing to transfer one message.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220525165852.33167-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver may return a timeout error even if the status register
indicates that the transfer may proceed. Fix this by restructuring
the polling loop.
Fixes: 89b35e3f28 ("spi: fsi: Implement a timeout for polling status")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220525165852.33167-2-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much dramatic changes at this time, but we've received quite
a lot of changes for ASoC, while there are still a few fixes and
quirks for usual HD- and USB-auido. Here are some highlights.
* ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
* Others
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver
-----BEGIN PGP SIGNATURE-----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=5qBk
-----END PGP SIGNATURE-----
Merge tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
This is quite a quiet release but some new drivers mean that the
diffstat is fairly large, the new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLh9wACgkQJNaLcl1U
h9ApgAf/SvcHRyM06hw+00D2PAco7mxSiAs7rebxj4f0zPRNvUrYbUDWjakeKjoB
ocmpY6AW/vRBUM9xZsiQiLp/9NPltnVghZIBgp5gcS8zaXdxiZjZ68Z+uYp9SP9v
zj8F6bBQzk3lvuY+Cr1f68iXICA62Aa1yX28UFVLZkV0d+0AazpECZkb3hjOiL6P
0qSV6IfoFlJXYsyvAS4/MqYrHklSCD/0Ek09V9jPpZJPHn1ldbFs5zkstfs0PMc/
YeDlpStkjJE4OQ6+z6Ou/wGbcw11nWvKCSqF4bGRXLrgR/uIjOKomwOzaBUf/A6Q
AxQcKMtsBTx0VzYmwJwopj0qDvOq/A==
=6yj3
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release but some new drivers mean that the
diffstat is fairly large. The new drivers include the aspeed driver
which is migrated from MTD as part of the ongoing move of controllers
with specialised support for SPI flashes into the SPI subsystem.
- Support for devices which flip CPHA during recieve only transfers
(eg, if MOSI and MISO have inverted polarity).
- Overhaul of the i.MX driver, including the addition of PIO support
for better performance on small transfers.
- Migration of the Aspeed driver from MTD.
- Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
IPM and SFI"
* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
spi: spi-au1550: replace ternary operator with min()
mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
spi: aspeed: Calibrate read timings
spi: aspeed: Add support for the AST2400 SPI controller
spi: aspeed: Workaround AST2500 limitations
spi: aspeed: Adjust direct mapping to device size
spi: aspeed: Add support for direct mapping
spi: spi-mem: Convert Aspeed SMC driver to spi-mem
spi: Convert the Aspeed SMC controllers device tree binding
spi: spi-cadence: Update ISR status variable type to irqreturn_t
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
spi: cadence-quadspi: remove unnecessary (void *) casts
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
spi: spi-imx: add PIO polling support
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
...
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKLf5EACgkQJNaLcl1U
h9ASqAf/YnwbFP919ree/DEKUDCNc4klUH5M4JOexXbZlZDqxKYRGZjoLuiwX/PQ
Au/xOjGEvm3Yg5/g5c8YFVNcIkv1O8VclRkV59oIxlBwKmQeTKvq+lOmlel2l1wZ
XOmvHjE46wxH1N1cLwL6KkX0YDn59orSZGYZRpfLjL61y6LQWsLNU0tY6AWCRATB
Llnrbu+DYgCsYNTEOOOY5s4V+4LkQm8TLdft91Va7mBdkPPRFoXRO0HGcVBqbkoN
7pf2mrjrLAWL9yuA8FlrgJbHq58DF9WGe5uEU7qlVL1zw46ClgIM0ABxPOdNdjV2
Wzb1jI7GmztgQNxlR9BcJB0kxAj9vA==
=oD5l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Merge series from Cédric Le Goater <clg@kaod.org>:
This series adds a new SPI driver using the spi-mem interface for the
Aspeed static memory controllers of the AST2600, AST2500 and AST2400
SoCs.
* AST2600 Firmware SPI Memory Controller (FMC)
* AST2600 SPI Flash Controller (SPI1 and SPI2)
* AST2500 Firmware SPI Memory Controller (FMC)
* AST2500 SPI Flash Controller (SPI1 and SPI2)
* AST2400 New Static Memory Controller (also referred as FMC)
* AST2400 SPI Flash Controller (SPI)
It is based on the current OpenBMC kernel driver [1], using directly
the MTD SPI-NOR interface and on a patchset [2] previously proposed
adding support for the AST2600 only. This driver takes a slightly
different approach to cover all 6 controllers.
It does not make use of the controller register disabling Address and
Data byte lanes because is not available on the AST2400 SoC. We could
introduce a specific handler for new features available on recent SoCs
if needed. As there is not much difference on performance, the driver
chooses the common denominator: "User mode" which has been heavily
tested in [1]. "User mode" is also used as a fall back method when
flash device mapping window is too small.
Problems to address with spi-mem were the configuration of the mapping
windows and the calibration of the read timings. The driver handles
them in the direct mapping handler when some knowledge on the size of
the flash device is know. It is not perfect but not incorrect either.
The algorithm is one from [1] because it doesn't require the DMA
registers which are not available on all controllers.
Direct mapping for writes is not supported (yet). I have seen some
corruption with writes and I preferred to use the safer and proven
method of the initial driver [1]. We can improve that later.
The driver supports Quad SPI RX transfers on the AST2600 SoC but it
didn't have the expected results. Therefore it is not activated yet.
There are some issues on the pinctrl to investigate first.
Tested on:
* OpenPOWER Palmetto (AST2400)
* Facebook Wedge 100 BMC (AST2400) by Tao Ren <rentao.bupt@gmail.com>
* Evaluation board (AST2500)
* Inspur FP5280G2 BMC (AST2500) by John Wang <wangzq.jn@gmail.com>
* Facebook Backpack CMM BMC (AST2500) by Tao Ren <rentao.bupt@gmail.com>
* OpenPOWER Witherspoon (AST2500)
* Evaluation board (AST2600 A0 and A3)
* Rainier board (AST2600)
[1] https://github.com/openbmc/linux/blob/dev-5.15/drivers/mtd/spi-nor/controllers/aspeed-smc.c
[2] https://patchwork.ozlabs.org/project/linux-aspeed/list/?series=212394
Fix the following coccicheck warnings:
drivers/spi/spi-au1550.c:408:21-22: WARNING opportunity for min()
drivers/spi/spi-au1550.c:542:21-22: WARNING opportunity for min()
min() macro is defined in include/linux/minmax.h. It avoids multiple
evaluations of the arguments when non-constant and performs strict
type-checking.
Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Link: https://lore.kernel.org/r/20220513130333.58379-1-guozhengkui@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In AST2600, the unit of SPI CEx decoding range register is 1MB, and end
address offset is set to the acctual offset - 1MB. If the flash only has
1MB, the end address will has same value as start address, which will
causing unexpected errors.
This patch set the decoding size to at least 2MB to avoid decoding errors.
Tested:
root@bletchley:~# dmesg | grep "aspeed-smc 1e631000.spi: CE0 window"
[ 59.328134] aspeed-smc 1e631000.spi: CE0 window resized to 2MB (AST2600 Decoding)
[ 59.343001] aspeed-smc 1e631000.spi: CE0 window [ 0x50000000 - 0x50200000 ] 2MB
root@bletchley:~# devmem 0x1e631030
0x00100000
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Potin Lai <potin.lai@quantatw.com>
[ clg : Ported on new spi-mem driver ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-12-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
To accommodate the different response time of SPI transfers on different
boards and different SPI NOR devices, the Aspeed controllers provide a
set of Read Timing Compensation registers to tune the timing delays
depending on the frequency being used. The AST2600 SoC has one of these
registers per device. On the AST2500 and AST2400 SoCs, the timing
register is shared by all devices which is problematic to get good
results other than for one device.
The algorithm first reads a golden buffer at low speed and then performs
reads with different clocks and delay cycle settings to find a breaking
point. This selects a default good frequency for the CEx control register.
The current settings are a bit optimistic as we pick the first delay giving
good results. A safer approach would be to determine an interval and
choose the middle value.
Calibration is performed when the direct mapping for reads is created.
Since the underlying spi-nor object needs to be initialized to create
the spi_mem operation for direct mapping, we should be fine. Having a
specific API would clarify the requirements though.
Cc: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-9-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver for the AST2400 SPI Flash Controller (SPI). This
controller has a slightly different interface which requires
adaptation of the 4B handling. Summary of features :
. host Firmware
. 1 chip select pin (CE0)
. slightly different register set, between AST2500 and the legacy
controller
. no segment registers
. single, dual mode.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-8-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not possible to configure a full 128MB window for a chip of the
same size on the AST2500 SPI controller. For this case, the maximum
window size is restricted to 120MB for CE0.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-7-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The segment registers of the FMC/SPI controllers provide a way to
configure the mapping window of the flash device contents on the AHB
bus. Adjust this window to the size of the spi-mem mapping.
Things get more complex with multiple devices. The driver needs to
also adjust the window of the next device to make sure that there is
no overlap, even if there is no available device. The proposal below
is not perfect but it is covering all the cases we have seen on
different boards with one and two devices on the same bus.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-6-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Use direct mapping to read the flash device contents. This operation
mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a
Control Register for the settings to apply when a memory operation is
performed on the flash device mapping window.
If the window is not big enough, fall back to the "User mode" to
perform the read.
Direct mapping for writes will come later when validated.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-5-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Data type of status variable, that hold the return value of the ISR,
should be irqreturn_t & not u32. This patch updates status variable type
to irqreturn_t.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220512145025.20205-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently devres managed removal of the spi_controller happens after
removing the power domain of the host platform_device.While this
does not affect the clean removal of the controller, but affects
graceful removal of the child devices if the child device removal
requires issuing commands over SPI.
Eg. flash device being soft reset to 1S-1S-1S mode before removal
so that on next probe operations in 1S-1S-1S mode is successful.
Failure is seen when `rmmod spi-cadence-quadspi` is performed:
root@j7-evm:~# rmmod spi_cadence_quadspi
[ 49.230996] cadence-qspi 47050000.spi: QSPI is still busy after 500ms timeout.
[ 49.238209] spi-nor spi1.0: operation failed with -110
[ 49.244457] spi-nor spi1.0: Software reset failed: -110
and on subsequent modprobe the OSPI flash probe fails as it
is in 8D-8D-8D mode since the previous soft reset did not happen.
root@j7-evm:~# modprobe spi_cadence_quadspi
[ 73.253536] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 73.260476] spi-nor: probe of spi0.0 failed with error -2
This commit adds necessary changes to perform spi_unregister_master()
in the host device remove() so that the child devices are gracefully
removed before the power domain is removed.
changes tested on J721E with mt35xu512aba flash.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220511115516.14894-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series update flags management in the following cases:
- In APM mode, don't take care of TCF and TEF flags
- Always check TCF flag in stm32_qspi_wait_cmd()
- Don't check BUSY flag when sending new command
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes has been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove a couple of unnecessary casts to `(void *)` when initializing the
`.data` members in the device ID table.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220510115141.212779-3-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
In mx51_ecspi_prepare_message() the MX51_ECSPI_CONFIG register is
setup for the current spi_message. After writing the register, there
is a delay to ensure that the changes hit the hardware.
This patch checks if the register MX51_ECSPI_CONFIG actually needs to
be changed. If the register content is unchanged the function is left
early, skipping the write to the hardware and the delay. This leads to
a small, but measurable performance increase. For a given workload
with small transfers on an imx6 single core the CPU load decreases
from 30% to ~27%.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-10-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supports several modes, one of them is PIO/IRQ
"spi_imx_pio_transfer()". The data is exchanged with the IP core using
PIO, an IRQ is setup to signal empty/full FIFOs and the end of the
transfer. The IRQ and scheduling overhead for short transfers is
significant. Using polling instead of IRQs can be beneficial to reduce
the overall CPU load, especially on small transfer workloads.
On an imx6 single core, a given RX workload of the mcp251xfd driver
results in 40% CPU load. Using polling mode reduces the CPU load to
30%.
This patch adds PIO polling support to the driver. For transfers with
a duration of less than 30 µs the polling mode instead of IRQ based
PIO mode is used. 30 µs seems to be a good compromise, which is used
the by the SPI drivers for the raspberry Pi (spi-bcm2835,
spi-bcm2835), too.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-9-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no need to embed the struct spi_bitbang into our private
data (struct spi_imx_data), the spi core is flexible enough, so that
we only need a pointer to the allocated struct spi_controller.
This is also a preparation patch to add PIO based polling support to
the driver.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-8-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
With patch:
| 8caab75fd2 ("spi: Generalize SPI "master" to "controller"")
the SPI "master" was generalized to "controller". This patch completed
the conversion of the spi-imx driver by replacing the remaining
occurrences of master to controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-7-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following sparse warning by using a swab32s()
instead of a cpu_to_be32(). The driver is used on little endian
systems only and we really want to swap the bytes.
| drivers/spi/spi-imx.c:305:29: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:305:29: expected unsigned int val
| drivers/spi/spi-imx.c:305:29: got restricted __be32 [usertype]
| drivers/spi/spi-imx.c:361:21: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:361:21: expected unsigned int [assigned] [usertype] val
| drivers/spi/spi-imx.c:361:21: got restricted __be32 [usertype]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-5-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following checkpatch warning, by making val an
"unsigned int".
| WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
| + unsigned val = 0;
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following checkpatch warning by removing the
trailing backslash:
| WARNING: Avoid unnecessary line continuations
| + spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the following and similar sparse warnings by adding
the missing identifier names to the function definitions:
| WARNING: function definition argument 'struct spi_imx_data *' should also have an identifier name
| #68: FILE: drivers/spi/spi-imx.c:68:
| + int (*prepare_message)(struct spi_imx_data *, struct spi_message *);
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It will cause null-ptr-deref if platform_get_resource_byname() returns NULL,
we need check the return value.
Fixes: 858e26a515 ("spi: spi-fsl-qspi: Reduce devm_ioremap size to 4 times AHB buffer size")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220505093954.1285615-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The module omap2-mcspi does not support the interword delay
parameter present in the spi transfer. On one side, if the module
is instructed to use the dma, this parameter is correctly ignored.
However, without the usage of the dma, that parameter should be
used.
The patch introduce the handling of such delay in the omap2-mcspi
module, using standard spi_delay struct. The patch has been tested
using as benchmark a DM3730.
The delay function used (spi_delay_exec) is already present in the
kernel and it checks on its own the validity of the input, as such,
no additional checks are present.
The range of usage of the udelay function is incremented to 200 us,
as the change from udelay to usleep_range introduces not
neglectible delays.
Signed-off-by: Andrea Zanotti <andreazanottifo@gmail.com>
Link: https://lore.kernel.org/r/20220502111300.24754-1-andreazanottifo@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -ENOMEM of there is a dma mapping error. Do not return success.
Fixes: 764f1b7481 ("spi: add driver for MTK SPI NAND Flash Interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/YmwjUcTKyQNrrn2g@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
The Cadence QSPI compatible string required for the SoCFPGA platform
changed from the default "cdns,qspi-nor" to "intel,socfpga-qspi" with
the introduction of an additional quirk in
commit 98d948eb83 ("spi: cadence-quadspi: fix write completion support").
However, that change did not preserve the previously used
quirk for this platform. Reinstate the `CQSPI_DISABLE_DAC_MODE` quirk
for the SoCFPGA platform.
Fixes: 98d948eb83 ("spi: cadence-quadspi: fix write completion support")
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220427153446.10113-1-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements support for the SPI-NAND mode of MTK NAND Flash
Interface as a SPI-MEM controller with pipelined ECC capability.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20220424032527.673605-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>:
1.Add support for using GPIOs as chip select lines on Ingenic SoCs.
2.Add support for probing the spi-ingenic driver on the JZ4775 SoC,
the X1000 SoC, and the X2000 SoC.
3.Modify annotation texts to be more in line with the current state.
Since version 5.13, the standard syscon bindings have been added
to all clps711x DT nodes, so we can now use the more general
syscon_regmap_lookup_by_phandle function to get the syscon pointer.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Link: https://lore.kernel.org/r/20220420061038.22570-1-eagle.alexander923@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220420090452.2588930-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085637.2541805-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110141.2559019-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
With the removal of the incorrect logic of cqspi_set_protocol(), ops with
cmd/addr buswidth >1 are now working correctly.
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash using 1-4-4
operations.
DTR operations are currently untested, so we leave them disabled for now
(except for the previously allowed 8-8-8 ops).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested, this removes the whole cqspi_set_protocol() function, as it
is not actually needed:
- Checks for unsupported operations are already handled by supports_op(),
removing the need to distinguish DTR and non-DTR modes in the buswidth
setup
- supports_op() ensures that the DTR flags match for all relevant parts of
an operation, so op->cmd.dtr can be used instead of copying the flag to
the cqspi_flash_pdata
- The logic in cqspi_set_protocol() is moved to cqspi_calc_rdreg() and
cqspi_write_setup() (with a helper macro CQSPI_OP_WIDTH())
The helper macro checks nbytes instead of buswidth for 0, for consistency
with supports_op() etc.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110103.2558955-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware (except for the ROCKCHIP_SPI_VER2_TYPE2 version) does not
support active-high native chip selects. However if such a CS is configured
the core does not error as it normally should, because the
'ctlr->use_gpio_descriptors = true' line in rockchip_spi_probe() makes the
core set SPI_CS_HIGH in ctlr->mode_bits.
In such a case the spi-rockchip driver operates normally but produces an
active-low chip select signal without notice.
There is no provision in the current core code to handle this
situation. Fix by adding a check in the ctlr->setup function (similarly to
what spi-atmel.c does).
This cannot be done reading the SPI_CS_HIGH but in ctlr->mode_bits because
that bit gets always set by the core for master mode (see above).
Fixes: eb1262e3cc ("spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20220421213251.1077899-1-luca.ceresoli@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085433.2541670-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220420090420.2588868-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085343.2541608-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085506.2541732-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
1.Since it would be dangerous to specify a newer SoC's compatible
string as the fallback of an older SoC's compatible string, we
add support for the "ingenic,jz4775-spi" compatible string in
the driver.
This will permit to support the JZ4775 by having:
compatible = "ingenic,jz4775-spi";
Instead of doing:
compatible = "ingenic,jz4775-spi", "ingenic,jz4780-spi";
2.Add support for probing the spi-ingenic driver on the X1000 SoC
from Ingenic. From the X1000 SoC onwards, the maximum frequency
allowed by the SSI module of Ingenic SoCs has been changed from
54MHz to 50MHz. So "max_speed_hz" is introduced in "jz_soc_info"
to set different maximum frequency values.
3.Add support for probing the spi-ingenic driver on the X2000 SoC
from Ingenic. The X2000 SoC has only one native chip select line,
so "max_native_cs" is introduced in "jz_soc_info" to set different
maximum number of native chip select lines.
4.Because of the introduction of support for the X-series SoCs, the
current driver is not only applicable to the JZ-series SoCs, so
the description texts has been modified to avoid misunderstanding.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1650724725-93758-4-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a helper to set driver_override to the reduce amount of duplicated
code.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: deba25800a ("spi: Add driver for IMG SPFI controller")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062641.10486-1-zhengyongjun3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The buffers passed in the data phase must be DMA-able. Programmers often
don't realise this requirement and pass in buffers that reside on the
stack. This can be hard to spot when reviewing code. Reject ops if their
data buffer is on the stack to avoid this.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420102022.3310970-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has always had a FIXME about this, and it seems
like this trivial code move avoids a mach header inclusion,
so just do it.
With that out of the way, and the header file inclusions
changed to global files, the driver can also be compile-tested
on other platforms.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the driver goes over the supported opcodes list each time
->exec_op() is called and finds the suitable for the given operation.
This consumes unnecessary amount of CPU cycles because the operation is
always the same. For this reason populate dirmap hooks for the driver so
that we cache the selected operation and then simply call it on each
read/write.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220420104350.19510-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
This series performs some cleanups to the spi-mt65xx driver, removing
all gotos, simplifying the probe function and adding kerneldoc to the
driver structures.
A few more fixes for SPI, plus one new PCI ID for another Intel chipset.
All device specific stuff.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmJe030ACgkQJNaLcl1U
h9BTnwf/VXTuq7Qn+xrWaA6tGJuYijgyc8vVUylutqJl6LaAMnk7NyPS5KWd1qx2
0Yejp8R961YxG6xjduiUJgWnAU0MPu0JOVnR8s0mt2MBWDuLh53aQBgWKvm247Sz
kN1mkSJcOWjzW0kVoY6XO8WW/Nofa8POtTR0CSxuwNByp6AGPay67BpyL586wej2
D/wUXnU7FMIOgE/GQ0OQJrbPQVPaqEGLjJrAVyszZxqfROdR6CHUODE2KtZ+EuGU
Je36I5W2F6eXiyMLNl9bdfXU7qMxIg66MPTFeeIM7QcfpscqTZVeo+0zMEaGXGvc
cg1ezRSq5wE8LisA8ZFUwVmHtSYw5A==
=7AEL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few more fixes for SPI, plus one new PCI ID for another Intel
chipset.
All device specific stuff"
* tag 'spi-fix-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
spi: cadence-quadspi: fix incorrect supports_op() return value
spi: intel: Add support for Raptor Lake-S SPI serial flash
spi: spi-mtk-nor: initialize spi controller after resume
Some definitions at the beginning of this file were wrongly
indented: fix the indentation for all of these and, while at
it, also move the MTK_SPI_IDLE and MTK_SPI_PAUSED down, as to
implicitly group the hardware related definitions to the
software (driver) related ones.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the two structures was already partially documented, but not
in kerneldoc format: enhance readability by adding the missing
documentation bits and use kerneldoc.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The last goto in the probe function can be removed by calling
pm_runtime_enable() right before devm_spi_register_master(), as
only some init checks were being performed after enabling pm.
This is a cleanup and brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reparenting sel_clk to parent_clk can be done before enabling any of
spi_clk and spi_hclk. Move the call to clk_set_parent() for sel_clk
earlier, and call disable_unprepare() upon spi_clk prepare_enable()
failure to remove all clock disablement related gotos.
This commit is in preparation of a later cleanup.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for switching to dev_err_probe() in this function, add
a pointer to struct device and replace all occurrences of '&pdev->dev'
to using this 'dev' pointer.
This is done for one-line fitting of the dev_err_probe() calls.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of performing yet another match check in the probe function,
simply switch to device_get_match_data().
This is a cleanup and brings no functional change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110226.2559081-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI_RX_CPHA_FLIP is set, flip CPHA on Rx only transfers. This is
useful to access devices that use inverted CPHA for MISO vs MOSI
signals.
Only support the mx51/mx53 variants for now.
Tested on i.MX6ULL based system.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/e11b4446afe9a46a282dd923d22c27d03fae15f8.1649702729.git.baruch@tkos.co.il
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220408080931.2494356-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220412070951.2532157-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220413093656.2538504-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The i.MX DMA drivers are device tree only, nothing in
include/linux/platform_data/dma-imx.h has platform_data in it, so move
the file to include/linux/dma/imx-dma.h.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220414162249.3934543-10-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard