Poke a few more bits into the SiI164 to make it
recover after S3. HEN/VEN are the important bits,
the rest PLL filter/HPD detection I just did
for good measure to match the BIOS programming.
Note that the spec recommended SCNT bit in REGC
isn't set by the BIOS at least for me, so I left
it out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221122120825.26338-4-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Poke a few more bits into the ch7xxx to make
it output a picture after being reset during S3.
In particular we need to set the input buffer select (IBS),
and enable VGA vsync output on the BCO pin. Selecting
VGA hsync on the c/h sync pin doesn't actually seem necessary
on my ADD card at least, but the BIOS selects it so why not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221122120825.26338-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Some gen2/gen3 parts have a 10bit gamma mode, on some pipes.
Expose it.
The format is different to the later i965+ style in that we
store a 10bit value and a 6 bit floating point slope for each
entry. Ie. the hardware extrapolates the intermediate steps
from the current LUT entry, instead of interpolating between
the current and next LUT entries. This also means we don't store
the last LUT entry in any register as it is defined by the previous
LUT entry's value+slope.
The slope has limited precision though (2 bit exponent + 4 bit
mantissa), so we'd have to allow for more error in the state checker
for the last entry and we have to make sure userspace doesn't
pass in something where the slope is simply to steep. In theory
we should perhaps check the slope for every interval, but we don't
do that for any other interpolated gamma mode and I suspect they
may also have some internal limit on the slope. I haven't confirmed
that theory though. Anyways, for ease of implementation we shall
just ignore the last entry in the state checker. If all the other
entries match anyway then that seems like a good indication that
the hardware was programmed as expected.
v2: Redo the state checker logic a bit
Rebase due to other changes
v3: Fix C8 readout
v4: Use REG_FIELD_PREP()
Acked-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-20-ville.syrjala@linux.intel.com
On hsw+ and glk class hardware we current make a mess of
things when we have to both generate limited range output
and use the hw gamma LUT. Since we do the range compression
using the pipe CSC unit (which is situated before the gamma
LUT in the pipe) we are in fact applying the gamma to the
limited range data instead of the full range data as the
user intended.
We can work around this by applying the range compression
via the gamma LUT instead of using the pipe CSC for it.
Fairly easy to do now that we have the internal post_csc_lut
attachment point where we can stick our new cooked LUT.
On hsw+ this only needs to be done when using the split
gamma mode or when the ctm is enabled since otherwise we can
simply reorder the LUT vs. CSC. On glk we need to do this any
time a gamma LUT is used since no reordering is possible.
We do lose a bit of coverage in intel_color_assert_luts(),
but so be it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-19-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
On glk we can no longer reorder the hw LUTS vs. pipe CSC like
we could on earlier platforms, and neither do we have a
separate output CSC like on icl+. That means if we use the
pipe CSC for YCbCr output we are currently applying the gamma
LUT after the RGB->YCbCr conversion, which is just wrong.
The further we go from a linear curve the more distorted the
resulting colors become.
To work around this terrible limitation the best we can do is
repurpose the hw degamma LUT as a poor man's gamma LUT. Now
that we have the internal pre_csc_lut attachment point that
is not particularly hard to do.
What makes this less than ideal however is the fact that the
hw degamma LUT and gamma LUTs have very different capabilities.
The gamma LUT can operate in direct color type modes, whereas
the degamma LUT can't and just always operates in interpolated
mode. Additionally the degamma LUT is just a single 1D LUT, whereas
the gamma LUT is made of three separate 1D LUts (one for each channel).
So in order to make this semi-sensible we must also verify the
user supplied LUT more less matches the hw degamma LUT capabilities.
We still end up losing most of the LUT entries though, so the results
might be a bit crap.
The other option of flat out rejecting the YCbCr+gamma LUT combo
seems extremely likely to just cause a black screen for the user.
Eg. pretty sure Xorg always applies some kind of gamma LUT, and
if the user then plugs in a display that needs YCbCr output we're
toast.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-18-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Currently crtc_state_is_legacy_gamma() has a very specific set
of conditions, not all of which are actually necessary. Also
when we detect those conditions check_luts() just skips all
the checks. That will no longer work for glk soon when we'll
start to use the hw degamma LUT in place of the hw gamma LUT
for YCbCr output. So let's rework the logic to only really consider
whether the user provided gamma_lut is one that matches the hw
legacy LUT capabilities or not.
We'll need to reject C8+degamma on ivb+ since the presence of
degamma_lut would either mean we have to really use the LUT
for degamma as opposed to C8 palette, or we have to enable
split gamma mode which also can't work as the C8 palette.
Otherwise this will now cause the legacy LUT to go through the
regular lut checks as well. As a side effect we also start to
allow the use of the legacy LUT with CTM, but that is perfectly
fine as far a the hardware is concerned.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-17-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
We have full readout now for all platforms (sans the icl+
multi-segment readout hw fail), so hook up the LUT state
checker for everyone.
We add a new vfunc for this since different platforms need
to handle the details a bit differently.
The implementation is rather repetitive in places. Probably
we want to think of a more declarative approach for the
LUT precision/etc. stuff in the future...
Note that we're currently missing readout for c8_planes, so
we'll have to skip the state check in that case.
v2: Fix readout for C8 use cases
v3: Skip C8 entirely due to lack of c8_planes readout
Add ilk_has_pre_csc_lut() helper and use other such helpers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-16-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Add the approproate c8_planes checks to make the LUT
code ready for C8 palette readout. Note we currently
lack the actual c8_planes readout, so this won't work
yet. But no harm in making the code somewhat more ready
for the day when we do get c8_planes readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-14-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Just like ivb+, ilk/snb can select whether the hw lut acts as
gamma or degamma. Make the readout cognizant of that fact.
v2: deal with pre_csc_lut
v3: use ilk_has_post_csc_lut() helper
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-13-ville.syrjala@linux.intel.com
We now have all the code necessary for gamma/degamma readout on
ivb/hsw. Plug it all in. As with bdw+ the cooked {pre,post}_csc_lut
make this trivial even in split gamma mode.
Note that on HSW if IPS is enabled the hardware will hang if
you try to access the LUT in split gamma mode. Thus we need to
reorder the LUT readout vs. IPS enable steps.
v2: deal with {pre,post}_csc_lut
split gamma is no longer a problem
handle HSW IPS w/a
v3: use ilk_has_post_csc_lut() helper
Reviewed-by: Uma Shankar <uma.shankar@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-12-ville.syrjala@linux.intel.com
Read out the gamma/degamma LUT on bdw+. Now that the
{pre,post}_csc_lut match the hardware LUT size even
in split gamma mode this is trivial.
v2: deal with {pre,post}_csc_lut
split gamma is no longer a problem
v3: add ilk_has_post_csc_lut() helper
Reviewed-by: Uma Shankar <uma.shankar@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-11-ville.syrjala@linux.intel.com
Read out the degamma LUT on glk+. No state cheker as of yet since
it requires dealing with the glk csc vs. degamma mess.
v2: deal with post_csc_lut
v3: add icl_has_{pre,post}_csc_lut(*) helpers
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-9-ville.syrjala@linux.intel.com
The degamma LUT is interpolated so we need the 128th (==1.0)
entry to represent the full < 1.0 input range. Only the 129th
and 130th entries are strictly for the >=1.0 extended range
inputs.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114153732.11773-7-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
bigjoiner_pipes() doesn't consider that:
- RKL only has three pipes
- some pipes may be fused off
This means that intel_atomic_check_bigjoiner() won't reject
all configurations that would need a non-existent pipe.
Instead we just keep on rolling witout actually having
reserved the slave pipe we need.
It's possible that we don't outright explode anywhere due to
this since eg. for_each_intel_crtc_in_pipe_mask() will only
walk the crtcs we've registered even though the passed in
pipe_mask asks for more of them. But clearly the thing won't
do what is expected of it when the required pipes are not
present.
Fix the problem by consulting the device info pipe_mask already
in bigjoiner_pipes().
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118185201.10469-1-ville.syrjala@linux.intel.com
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Enable the SDP split configuration for DP2.0.
v2: Move the register handling out of compute config function (JaniN)
v3: Patch styling and register access based on platform support (JaniN)
v4: Rebased
v5: Use unconditional clear bit in intel_de_rmw (Jani Nikula)
Bspec: 67768
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121150718.1117628-1-vinod.govindapillai@intel.com
As per bSpec MTL has 38.4 MHz Reference clock.
Adding the cdclk tables and cdclk_funcs that MTL
will use.
v2: Revert to using bxt_get_cdclk()
BSpec: 65243
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117230002.792096-3-anusha.srivatsa@intel.com
For MTL, changing cdclk from between certain frequencies has
both squash and crawl. Use the current cdclk config and
the new(desired) cdclk config to construct a mid cdclk config.
Set the cdclk twice:
- Current cdclk -> mid cdclk
- mid cdclk -> desired cdclk
Driver should not take some Pcode mailbox communication
in the cdclk path for platforms that are Display version 14 and later.
v2: Add check in intel_modeset_calc_cdclk() to avoid cdclk
change via modeset for platforms that support squash_crawl sequences(Ville)
v3: Add checks for:
- scenario where only slow clock is used and
cdclk is actually 0 (bringing up display).
- PLLs are on before looking up the waveform.
- Squash and crawl capability checks.(Ville)
v4: Rebase
- Move checks to be more consistent (Ville)
- Add comments (Bala)
v5:
- Further small changes. Move checks around.
- Make if-else better looking (Ville)
v6: MTl should not follow PUnit mailbox communication as the rest of
gen11+ platforms.(Anusha)
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117230002.792096-2-anusha.srivatsa@intel.com
cdclk_sanitize() function was written assuming vco was a signed integer.
vco gets assigned to -1 (essentially ~0) for the case where PLL
might be enabled and vco is not a frequency that will ever
get used. In such a scenario the right thing to do is disable the
PLL and re-enable it again with a valid frequency.
However the vco is declared as a unsigned variable.
With the above assumption, driver takes crawl path when not needed.
Add explicit check to not crawl in the case of an invalid PLL.
v2: Move the check from .h to .c (MattR)
- Move check to bxt_set_cdclk() instead of
intel_modeset_calc_cdclk() which is directly in
the path of the sanitize() function (Ville)
v3: remove unwanted parenthesis(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117230002.792096-1-anusha.srivatsa@intel.com
Follow the modern style and rename most 'dev_priv' variables
to 'i915'.
intel_dvo_init_dev() is the sole exception since it needs the
magic 'dev_priv' variable for the DPLL register macros.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118105525.27254-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The loop over intel_dvo_devices[] makes intel_dvo_init()
an ugly mess. Pull the i2c device probe out to a separate
function so that we can get rid of the loop and flatten
the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118105525.27254-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
intel_dvo.panel_wants_dither is only set but never used.
We can't do dithering on the gmch side anyway since the
dithering logic is part of the integrated LVDS port and
not available for other output types.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221118105525.27254-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DG2 has been very usable for a while now, and all of the uapi changes
related to fundamental platform usage have been finalized. Recent CI
results have also been healthy, so we're ready to drop the force_probe
requirement and enable the platform by default.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221109001328.732000-1-matthew.d.roper@intel.com
MTL LPDDR5 reported 16b with 8 channels. Previous platforms
reported 32b with 4 channels and hence needed a multiplication
by a factor of 2. Skip increasing the channels for MTL.
v2: Use version check instead of platform check(MattR)
Bspec: 64631
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117213015.584417-2-radhakrishna.sripada@intel.com
MEM_SS_INFO_GLOBAL Register info read from the hardware is cached in val. However
the variable is being modified when determining the DRAM type thereby clearing out
the channels and qgv info extracted later in the function xelpdp_get_dram_info. Preserve
the register value and use extracted fields in the switch statement.
Fixes: 825477e779 ("drm/i915/mtl: Obtain SAGV values from MMIO instead of GT pcode mailbox")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117213015.584417-1-radhakrishna.sripada@intel.com
Add stepping-substepping info in accordance to bpsec changes.
Bspec: 55376
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221117214132.152061-1-matthew.s.atwood@intel.com
MTL+ requires the AUX_IO power for the main link only on eDP, so don't
enable it in other cases.
v2:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-10-imre.deak@intel.com
Factor out functions to get/put the AUX_IO power domain for the main
link on DDI ports.
While at it clarify the corresponding code comment.
No functional change.
v2:
- s/(get/put)_aux_power_for_main_link/main_link_aux_power_domain_(get/put)
(Jani)
- Clarify in the code comment that AUX_IO is needed only by TypeC besides
eDP/PSR.
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Don't call fetch_and_zero() with side-effect during variable
declaration. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-9-imre.deak@intel.com
Add the missing DC_OFF power domain -> DC_OFF power well mappings on all
platforms. This didn't cause a problem as the DC_OFF power domain is
only used on JSL, where the mapping was already correct.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-8-imre.deak@intel.com
BXT and GLK were missing the AUX_IO_A power domain -> PHY A common power
well mapping, add these now. This didn't cause a problem as the
AUX_IO_A and DDI_LANES_A power domains are acquired together.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-7-imre.deak@intel.com
Starting with TGL eDP is supported on ports B+ (besides port A), so make
sure DC states are not blocked on any such ports. For this add an
AUX_IO_<port> power domain for each port with eDP support. These domains
similarly to AUX_IO_A enable only the AUX_IO_<port> power well for an
enabled port, whereas the existing AUX_<port> domains enable both the
AUX_IO_<port> and the DC_OFF power wells as required by DP AUX transfers.
v2: (Ville)
- Split the change using AUX vs. AUX_IO on port A to a separate patch.
- Select AUX_IO vs. AUX based on crtc_state->has_psr instead of
is_edp().
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Fix warn in intel_display_power_aux_io_domain(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-6-imre.deak@intel.com
Use the AUX_IO_A display power domain only for eDP on port A where PSR
is also supported. This is the case where DC states need to be enabled
while the output is enabled - ensured by AUX_IO_A domain not enabling
the DC_OFF power well. Otherwise port A can be treated the same way as
other ports with an external DP output: using the AUX_<port> domain
which disables the unrequired DC states.
This change prepares for the next patch enabling DC states on all ports
supporting eDP/PSR besides port A.
v2:
- Check the encoder PSR capability instead of PSR being enabled in the
crtc_state, as the latter can be changed with a fastset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-5-imre.deak@intel.com
Move the definition of the AUX_IO_A power domain, requiring only the
corresponding AUX_IO_A power well to be enabled, before all the
AUX_<port> power domains, which require both the AUX_IO_<port> and the
DC_OFF power wells to be enabled.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-4-imre.deak@intel.com
Since the current size of intel_display_power_domain_set struct is
close to 1kB, it's better to use preallocated memory for it. The only
user of the intel_display_power_get/put_in_set() allocating the struct
on stack is hsw_get_pipe_config(), so we can avoid potential stack
overallocations by moving the struct here to the preallocated
intel_crtc struct (hsw_get_pipe_config() is non-reentrant wrt. each
CRTC).
This patch replaces
https://lore.kernel.org/intel-gfx/20221107170917.3566758-5-imre.deak@intel.com/T/#md3f6cdf17fcd
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-3-imre.deak@intel.com
The intel_display_power_*_domain() functions should always warn if a
default domain is returned as a fallback, fix this up. Spotted by Ville.
Fixes: 979e1b32e0 ("drm/i915: Sanitize the port -> DDI/AUX power domain mapping for each platform")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-2-imre.deak@intel.com
Fix up some function argument alignment fails.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221108151839.31567-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>